Niceday CT11PRO Elliptical Machine User Manual

Niceday CT11PRO Elliptical Machine

Important Safety Information

For correctly assemble and safe use, please read all caution carefully

1. Please read this manual entirely before assembling and using this equipment. Safe use can only be achieved under the premise of proper assembly, maintenance, and use of the equipment. Please ensure that all users are clear of the precautions for this equipment.

2. Before using this equipment, please consult your doctor to determine if your health meets the conditions to use this equipment.

3. Incorrect or excessive exercise will affect your health. Please pay attention to the body signals.

4. Keep pets and young children away from the equipment.

5. Before moving the equipment, please tightly lock the vertical tube with the connecting bolt.

6. Warm-up stretching is recommended before exercise.

7. Put this equipment on the solid and flat floor. And make sure there is no barrier affect on the equipment running.

8. Before using, please tighten all screws and bolts.

9. To extend the equipment’s used life, please inspect and tighten the screws and bolts
   regularly. And contact the seller to replace the damaged parts in time.

10. Always use the equipment following the user manual. If you find any defective components or unusual noises during exercise, please stop using the equipment and contact the seller.

11. The recommended user weight is 400 LBS. The user’s age should be over 13.

12. Please wear suitable clothing when using this equipment. Loose or dangling clothing is not recommended.

13. It is forbidden to place fingers or objects into the moving parts.

14. Please store this equipment in a cool and dry environment and don’t leave it in extremely cold, hot, or damp areas to avoid product damages.

15. This equipment is suitable for home and office use only. Please do not use it for public or commercial purposes.

Part List

1. Before assembling the product, please check the received accessories according to this list.
2. If any parts are damaged or missing, please kindly contact the seller to get free replacements.
   Service email : nicedayfitness@outlook.com

Assembly Steps

STEP 1: Assemble the front leg tube(with wheels) and the rear leg tube 【Parts required: 18/19/20】

1. Remove the pre-assembled M10*90 bolts(20) from the leg tubes(18)(19).
2. Connect the leg tubes to the mainframe(14) with the M10*90 bolts(20).
3. Tighten the bolts with wrench 23-B.
   Note: The square bolt ends should be completely inserted into the square holes on the leg tubes. Test: Shake the mainframe to test for any wobbling or unusual noises. If you notice any of these problems, please tighten the M10*90 bolts securely.

STEP 2: Unfold the vertical tube from the mainframe

1. Unfold the vertical tube from the mainframe(14).
2. Insert the end of the vertical tube into the base tube.
   Note: Bolt B should stay on top of the elliptical groove at last.

STEP 3: Locking the vertical tube

1. Locking the vertical tube via the M878 Bolt(6) and 5pcs of M820 Screws(17).
2. Tighten the bolts and screws with Allen key (23-A) and wrench (23-B).
   Note: Please tighten all bolts and screws of this position thoroughly. The screw’s insufficient tightening will cause squeaking noise during use.

STEP 4: Fix the decorative cap and sealing ring 【Parts required: 21】

1. Press and secure the decorative cap onto the mainframe.
2. Insert the sealing ring(21) into the gap of the decorative cap.

STEP 5: Assemble the pulse handle 【Parts required: 13/8/9】

1. Remove pre-assembled M8*30 screw(8) from top of the vertical tube.
2. Attach the pulse handle(13) to the vertical tube with the M8*30 screw(8).
3. Tighten the screws with Allen key 23-A
4. Press the screw cover(9) to the middle of the pulse handle.

STEP6: Assemble the handles 【Parts required: 1/2/5】

1. Remove pre-assembled M8*42 Bolts(5) from the handles(1)(2).
2. Attach the left handle(1) and right handle(22) to the rockers with M8*42 bolts(13).
3. Tighten the bolts with Allen key (23-A).

STEP 7: Assemble the Screw covers for the handles 【Parts required: 10-L/10-R/11-L/11-R/12/22】

1. Attach the screw covers(10-L)(10-R)(11-L)(11-R) to the connection position of the handles and the rockers.
2. Fix the screw covers with the M513 screws(12) and M416 screws(22).
3. Tighten the screws with Allen key (23-A).

STEP8: Assemble the digital watch 【Parts required: 3/4】

1. Connect the digital watch(3) to the induction wire.
2. Remove the pre-assembled M5*10 screws(4) from the back of the digital watch.
3. Then fix the digital watch to the vertical tube with the M5*10 Screws(4).
4.  Tighten the screws with Allen key (23-A) .
5. Connect the pulse handle’s wire to the digital watch(3)

STEP 9: Assemble the pedals. 【Parts required: 15/16/7】

1. Attach the left and right pedals(15)(16) to the pedal support tube with M8*42 Bolts(7).
2. Tighten the bolts with wrench (23-B).

STEP 10: Test the elliptical machine

Pedal the elliptical machine for 10 minutes, to confirm if the machine exists the following issues.

1. Strange sounds
2. Jerky movement
3. Digital watch showing issue

Contact us if you met any of the above issues.
Contact way:  nicedayfitness@outlook.com
We will reply to your email within 24 hours.

Exploded view

Digital watch instruction

Button’s Function

MODE: Press to select the different modes, including TIME, SPEED, DISTANCE, CALORY, ODO, and PULSE.
Extended press the MODE button will turn all values to 0.
SET: To set time, distance, and calories as exercise goals.

Setting step : Time as an example.

1. Press MODE to turn to TIME mode(without SCAN).
2. Press SET to set your exercise time goals.
3. Each time you press the SET button, the time will increase by 1 minute, 99 minutes most.
4. Pedal the elliptical machine, the watch will countdown your goal.
5. The watch will alarm 10 seconds when the countdown finishes.
   RESET: Press to reset time, distance, and calories. Short time press will turn the value of the current MODE to 0. Extended-press will turn all values to 0 except ODO MODE. If you need to reset ODO, please take off the battery and install it again.
   

Different Mode

1. SCAN: Press the MODE button until SCAN appears in the upper left corner of the screen. The watch will turn into SCAN mode. In this mode, the watch will cycle display data through 6 modes, TIME, SPEED, DISTANCE, CALORIES, ODO. Each mode will be displayed for 6 seconds.
   Note: You can’t set exercise goals in the SCAN mode, press MODE until SCAN disappears in the upper left corner to exit the SCAN mode.

2. TIME: (1)Count the total exercise time. (2)Press the MODE button to turn to TIME mode. The system defaults to run SCAN mode in TIME mode. Press one more time will stay in TIME mode without SCAN.

3. SPEED: Display current speed.

4. DIST: Count the total distance of exercise.

5. CAL: Count the total calories for the whole exercise period.

6. ODO: Count the total distance within one battery capacity running period.

7. PULSE: (1)Measure the current pulse. (2)Press the MODE button to turn to PULSE mode. Place your palms on both of the contact pads. The watch will show the current heartbeat rate in beats per minute(BPM) on the LCD after 6~7 seconds.

Remark: During the process of pulse measurement, the measurement value may be higher than the actual pulse rate in the first 2~3 seconds due to contact jamming, then will recover to the exact level. The measurement value cannot be reference for medical treatment.

Other Instructions for The Digital watch

1. ALARM: The watch will “Beep” when press the MODE, SET, and RESET buttons together.

2. AUTO ON/OFF & AUTO START/STOP:
   The power will turn off automatically if receive no signal for 4 minutes. As long as the rockers are in motion status or press any buttons, the watch will be in working status.

3. Cumulative Data:
   The watch will stop counting when the pedals stop running. The data will be auto cumulative. If you need to recount data, short-press the RESET button to reset a single data, and extended-press the RESET button to reset all data.

Exception Description

1. If the digital watch doesn’t display data or the display is blurred, please replace the battery.
2. The digital watch will automatically shut down after 4 minutes of non-use.
3. The digital watch will automatically power on when the pedal moves or pressing the button.
4. The digital watch will automatically calculate the exercise data when starting to exercise and stop calculating the exercise data after 4 seconds of stopping the exercise.

KINOMAP Connection Instructions

1. The IOS mobile phone system must be higher than version 7.1 and must support Bluetooth BLE 4.2
   (iPhone 4S or higher).

2. The Android system requires version 4.3 or above, and must support Bluetooth BLE 4.2.

3. The wireless transmitter in the device can only record the user’s data and send it to the mobile APP
   when it is connected to the mobile phone.

4. Before starting the sports equipment, please connect the application to the equipment to ensure that
   the data recorded in the mobile application is valid.

5. When Bluetooth does not receive a motion signal within 4 minutes, it will enter sleep mode.

6. In sleep mode, the mobile phone will not be able to search for Bluetooth signals. At this time, consumers need to move the pedals to wake up the Bluetooth transmitter of the sports device.

Connection steps

1. Search “KINOMAP” in the mobile application store to download the application.
2. The Android system requires version 4.3 or above, and must support Bluetooth BLE 4.2.
3. The wireless transmitter in the device can only record the user’s data and send it to the mobile APP when it is connected to the mobile phone.
4. Before starting the sports equipment, please connect the application to the equipment to ensure that the data recorded in the mobile application is valid.
5. When Bluetooth does not receive a motion signal within 4 minutes, it will enter sleep mode.
6. In sleep mode, the mobile phone will not be able to search for Bluetooth signals. At this time, consumers need to move the pedals to wake up the Bluetooth transmitter of the sports device.

Connection steps

1. Search “KINOMAP” in the mobile application store to download the application.
   

2. Download the APP and register your personal information.

3. Turn on the Bluetooth of the mobile phone, and make sure that the transmitter is powered on and in working condition.

4. Add exercise equipment.

The specific operation is as follows:

Documents / Resources

| Niceday CT11PRO Elliptical Machine [pdf] User Manual
CT11PRO Elliptical Machine, CT11PRO, Elliptical Machine, Machine
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>