YETI SB120 Mountain Bike Feature Instruction Manual

YETI SB120 Mountain Bike Feature

Product Information

Specifications:

• Models: SB120, SB135, SB140, SB160
• Product: Bike Frame Protection Kit

Product Usage Instructions

What You’ll Need to Get Started:
Before you begin, make sure you have the following items ready:

1. Mild soap and water for cleaning the bike
2. Nitrile/latex gloves or clean hands
3. Spray bottle filled with water and a drop of soap
4. Squeegee for flattening the decal
5. Heat gun or hairdryer (low setting)
6. Clean cloth or towel

Instructions:

1. Clean the bike thoroughly with mild soap and water before applying the decals.
2. Wash your hands or wear gloves to avoid dirt transfer.
3. Prepare a spray bottle with water and a drop of soap for easier application.
4. Spray the frame area and adhesive side of the decal before placement.
5. Position the decal as instructed, adjusting as necessary.
6. Use the squeegee to flatten the decal onto the frame, starting from the middle.
7. Remove excess water under the decal using a cloth or towel.
8. Apply heat to the edges with a heat gun/hairdryer and flatten any bumps with a rag or squeegee.
9. To remove the decal, warm up the adhesive with a heat gun and peel back slowly.
   Note:
   You can create custom shapes by cutting out remaining decal scraps for a unique look!

Decals Placement:
Follow the specific instructions for placing decals on different parts of the bike:

• BOTTOM BRACKET: Ensure alignment with frame hole and parallel to frame edge.
• SWITCH BRACE: Center decal with relief cutouts on brace bends.
• DOWNTUBE: Center above rubber protector. For XL/XXL frames, add extension decal.

Frequently Asked Questions (FAQ)

• Can I reposition the decals once applied?
  It is recommended to position the decals correctly during initial placement. Repositioning may affect adhesion quality.

• How do I remove the protective decals without damaging the frame?
  Use a heat gun to warm up the adhesive before slowly peeling off the decal. Clean any residue with mild soap and water.

WHAT YOU’LL NEED TO GET STARTED

• Lint free rag
• Spray bottle with soap
• Hair dryer / heat gun
• Clean bike
• Clean hands
• Measuring device

INSTRUCTIONS

1. Clean bike thoroughly with mild soap and water prior to decal application. It is best if you can apply decals on a new frame.
2. Wash hands before application or wear a pair of nitrile/latex gloves to keep any dirt from sticking to the decal.
3. Get a spray bottle full of water. Add a drop or two of soap to help the decals slide around if needed.
4. Working with one decal at a time, spray the appropriate area of the frame and adhesive-side of the decal.
5. Place decal in the locations provided below, re-placing or sliding decal as needed.
6. Once the decal is in the right spot, use the provided squeegee to start flattening the decal onto the frame. Start in the middle, working along the middle length. Gradually squeeze out the water toward the edges, working thoroughly and patiently to remove ALL water under the decal.
7. Use a clean cloth or towel to help lay the decal flat and wipe off excess water. At this point, some edges of the decals might not be perfectly flat on the frame.
8. Using a heat gun or hairdryer on low setting, apply heat to the decal edges for 2-3 seconds at a time. Using a clean rag or squeegee, work on any edges or bumps to lay them flush to the frame. Re-apply heat and repeat as necessary.
9. When it’s time to remove or replace your protective decals, use a heat gun to warm up adhesive and pull back decal slowly. Do not remove without warming up decal adhesive first. Clean off any residual adhesive with mild soap and water.
   NOTE:
   Feel free to cut out any custom shapes you might want using the remaining decal scraps. Get creative!

DECALS

ASSEMBLY INSTRUCTION

• BOTTOM BRACKET
  Assure the drain hole in the bottom of frame is centered in the decal slot, and the side of the decal is parallel with the side edge of the frame. Place the decal behind the rubber protector.

• SWITCH BRACE
  Center decal on switch brace, placing relief cutouts on the bends in the brace.

• DOWNTUBE

  • Center decal on downtube, placing it above rubber protector. For XL and XXL frames, place downtube extension decal above downtube decal.
  • If running a shuttle guard, place shuttle guard decal between rubber protectors instead of downtube decal.

• TOP TUBE
  Center decal on top tube. Decal will wrap around top tube corners. Place decal behind headset.

• SEAT TUBE

  • Center decal on back of seat tube, and place relief cuts on transition from switch brace to straight section of seat tube.
  • For larger frames, use seat Tube extension decal above seat tube decal.

• REAR TRIANGLE BRIDGE
  Center bridge decal on rear triangle bridge, with decal ‘shoulders’ touching lining up with the start of curvature at the top of the bridge. Wrap the decal around the top and bottoms of the bridge.

• INNER CHAINSTAYS
  Line up inner edge with bridge decal. Center decal between rubber guards on right side. Center decal on chainstay on left side.

• RIGHT SEATSTAY/CHAINSTAY OUTER
  Center decals between rubber protectors and line up cutouts with rubber guards .

• LEFT SEATSTAY/CHAINSTAY OUTER
  Center decals on chainstay and seatstays. Assure chainstay decal is behind any graphics.

• INNER SEATSTAY
  Center decals on seatstays, with rear edges of decals ~345mm from axle for 29” tires.

• ROTOR GUARD
  Place on inside of chainstay, just ahead of dropout.

• REAR DERAILLEUR
  Line up decal with bottom of outer chainstay decal. Front of decal should be just behind derailleur port, with relief cut running along channel in carbon.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>