YETI SB140 Mountain Bicycle Owner’s Manual

: June 4, 2024
: YETI

Table of Contents

YETI SB140 Mountain Bicycle Owne
FRAME ASSEMBLY
REBUILD KITS CONTINUED
LIFETIME WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

YETI SB140 Mountain Bicycle Owne

YETI-SB140-Mountain-Bicycle-product-
image

CONGRATULATIONS ON YOUR PURCHASE OF A NEW YETI.

We are confident your new bicycle will exceed your expectations for value, performance, and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience. Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun. This model specific manual is designed to be used in conjunction with the general Yeti Owner’s Manual and the manuals supplied by the suspension manufacturers. If you did not receive the Yeti owner’s manual or the manual provided by the suspension manufacturer, download the materials off the Internet, or contact your local dealer. Bicycling can be a hazardous activity even under the best of circumstances. Proper maintenance of your bicycle is your responsibility and when done properly helps reduce the risk of injury and damage to your bicycle. This manual outlines basic setup and maintenance recommendations of your new Yeti. Because it is impossible to anticipate every situation or condition that may occur during the assembly, setup, and maintenance of your bicycle, Yeti recommends that all service and repairs be performed by your local authorized Yeti Dealer. This manual contains many “Warnings” and “Cautions” concerning the consequences of failure to maintain or inspect your bicycle. The word “Warning” indicates a potentially hazardous situation in which , if not avoided, could result in serious injury or death. The word “Caution” indicates a potentially hazardous situation in which, if not avoided may result in minor injuries or damage to your bicycle or a component of your bicycle. Be sure to read and understand all of the Warnings and Cautions listed in the manual.

Warning: Make sure you review and understand the warnings, instructions, and content of this manual and accompanying manuals for your bicycle.
Warning: Technological advances have made bicycles and bicycle components more complex and the pace of innovation is increasing. It is impossible for this manual or the accompanying manuals to provide all the information required to properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Yeti retailer.

THE LOWDOWN ON THE SB140/LR AND ITS FEATURES.

SWITCH INFINITY TECHNOLOGY PATENTED SUSPENSION SYSTEM
HIGH MODULUS CARBON FIBER MAIN FRAME AND SWING ARM
COLLET AXLE SYSTEM ON PIVOTS REDUCES BEARING WEAR
OPTIMIZED FOR 1X DRIVETRAINS ONL Y
ISCG 05 CHAINGUIDE MOUNTS
INTE RATED HEAD TBE 41MM/52MM
SUSPENSION BY FOX
CUSTOM DEBRIS AND CHAIN SLAP GUARDS
INTERNAL CABLE ROUTING
INTEGRATED AXLE AND DERAILLEUR HANGER SYSTEM
The SB140/LR delivers 140 mm of travel with our patented Switch Infinity Technology. Efficient pedaling performance while still smooth and continuous when the going gets rough.
High modulus carbon provides a stiff, strong and light weight chassis.
Collated pivot axles help create a stiff interface between the front and rear triangles of the frame. Custom Endure Max sealed bearings keep things moving freely at the pivots.
The SB140/LR does away with the front derailleur mount, making it a 1x drive specific frame. This increases stiffness in the frame.
ISCG 05 chain guide mounts are included on the SB140/LR if case you want to go for some extra drivetrain security in the rowdy sections.
Using our integrated head tube on the SB140/LR allows for a larger head tube with more area, increased stiffness, and lower overall ride height without compromising any performance.
The SB140 uses a 210 x 55 mm Float DPS shock by Fox Racing Shod. The SB140LR uses a 210 x 55mm Float X shock by Fox Racing Shod.
Custom guards on the seat stay, chain stay and down tube keep things quiet while riding and protect the frame.
The SB140/LR features internal routing for all cables, making the bike quiet and clean looking as well as reducing cable rub on the paint.
Dedicated 12 x 148 Boost dropouts and integrated hanger with axle threads for strength, stiffness, ease of hanger and wheel installation.

YETI-SB140-Mountain-Bicycle-01

FIT

X-SMALL 4’11” (150 CM) – 5’3″ (160 CM)
SMALL 5’1″ (155 CM) – 5′ 7″ (170 CM)
MEDIUM 5’5″ (165 CM) – 5’11” (180 CM)
LARGE 5’10” (178 CM) – 6’3″ (191 CM)
X-LARGE 6’1″ (185 CM) – 6’7″ (200 CM)

FOX 36 / 150MM FORK

XS SM MD LG XL
SEAT __TUBE LENGTH 409.6 434.6 464.5 484.5
509.5 EFF. TOP TUBE LENGTH 536.9 565.8 597.2 620.1 648.1
HEAD TUBE ANGLE 65.5 65.4 65.4 65.4 65.4
EFF. SEAT TUBE ANGLE 77.6 77.5 77.5 77.4 77.3
CHAINSTAY LENGTH 433.0 433.0 433.0 433.0 433.0
WHEELBASE 1140.2 1171.3 1203.6 1228.3 1257.9
EST. BB HEIGHT 336.6 336.6 336.7 336.8 336.9
STANDOVER 698.4 703.8 706.2 708.6 711.0
HEAD TUBE LENGTH 95.5 109.9 115.4 126.4 137.5
AXLE TO CROWN 539.1 539.1 539.1 539.1 539.1
FORK OFFSET 37.5 37.5 37.5 37.5 37.5
STACK 578.8 591.7 596.5 606.4 616.3
REACH 409.6 434.6 464.5 484.5 509.5
FRONT CENTER 707.3 738.4 770.7 795.4 825.0
VERTICAL FORK TRAVEL 136.4 136.4 136.4 136.4 136.4

YETI-SB140-Mountain-Bicycle-02

X-SMALL
SMALL
MEDIUM
LARGE
X-LARGE| 4’11” (150 CM) – 5’3″ (160 CM)
5’1″ (155 CM) – 5′ 7″ (170 CM)
5’5″ (165 CM) – 5’11” (180 CM)
5’10” (178 CM) – 6’3″ (191 CM)
6’1″ (185 CM) – 6’7″ (200 CM)
---|---
__ 9.|

FOX 36 / 160MM FORK

XS SM MD LG XL

SEAT TUBE LENGT 355.0 380.0 410.0 450.0 495.0
B EFF. TOP TUBE LENGTH 65.0 65.0 65.0 65.0 65.0
EFF. SEAT TUBE ANGLE 77.1 77.0 77.0 77.0 76.9
CHAINSTAY LENGTH 433.0 433.0 433.0 433.0 433.0
WHEELBASE 1144.8 1175.9 1208.2 1232.9 1262.6
EST. BB HEIGHT 339.9 339.9 339.9 339.9 339.9
STANDOVER 702.4 707.6 710.0 712.3 714.7
HEAD TUBE LENGTH 95.5 109.9 115.4 126.4 137.5
AXLE TO CROWN 549.1 549.1 549.1 549.1 549.1
FORK OFFSET 37.5 37.5 37.5 37.5 37.5
STACK 581.9 594.9 599.9 609.9 919.9
REACH 405.1 430.1 460.1 480.1 505.1
FRONT CENTER 711.8 742.9 775.2 799.9 829.6
VERTICAL FORK TRAVEL 145.0 145.0 145.0 145.0 145.0

OVERVIEW
Following these guidelines will help maintain the performance of your bicycle and prevent more serious problems from arising. It is important to remember that service intervals can vary depending on climate, trail conditions and riding frequency. If you are unsure about working on your own bicycle, contact your authorized Yeti Dealer for more information on general bicycle maintenance.

SCHEDULE

CLEAN AND LUBE CHAIN

| MONTHLY| 3 MONTHS| ANNUALLY
---|---|---|---
CHECK TIRE PRESSURE| | |
CLEAN BIKE OF MUD AND DEBRIS| | |
CHECK BRAKE FUNCTION| | |
CHECK SHOCK PRESSURE| | |
CHECK FOR LOOSE BOLTS AND TIGHTEN, IF NECESSARY| | |
CHECK HEADSET AND TIGHTEN / LOOSEN, IF NECESSARY| | |
THOROUGHLY CLEAN PIVOT POINTS WITH A RAG (DO NOT LUBRICA TE)| | |
LUBE INFINITY LINK EVERY 40 HRS. (YETI HEAVY MOLYBDENUM GREASE)| | |
CHECK / REPLACE BRAKE PADS| | |
CHECK TIRES FOR WEAR| | |
CHECK SPOKE TENSION. RETENTION, IF NECESSARY| | |
CHECK CHAIN FOR WEAR. REPLACE IF NECESSARY| | |
COMPLETE TUNE-UP PERFORMED BY AN AUTHORIZED YETI DEALER| | |

TORQUE
Yeti strongly recommends using a torque wrench when assembling your frame. Torque specifications for individual parts on the SB140/LR are listed below, as well as in the step by step assembly instructions later in the manual. For general bicycle maintenance please consult the torque specifications of the component you are adjusting.

KEY TORQUE SPECS

PART NUMBER	DESCRIPTION	TORQUE (NM)
300040485	MAIN PIVOT AXLE	12
200020327	SS PIVOT BOLT, FEMALE	16
300030296	COLLET AXLE 30.5X10.5 M10X1.0	13
300040454	COLLET WEDGE BOLT, LARGE	14
300030293	LINK, PIVOT HARDWARE, MALE, 15MM	15
300060073	12X148 DERAILLEUR HANGER	10
300030057	SHCS M6x1.0 20L, SWITCH LINK MOUNT	12
300040486	COLLET WEDGE BOLT, SMALL	8
100425006	AXLE, YETI BOLT ON, 12X148MM	12-15
300030151	BOLT, TI MALE, M6 X 12.0 MM	10
200020311	LOCKRING, 6902-2RS	20

SEATPOST CABLE ROUTING

With a 3mm Allen key, remove the lower cable port access cover near the bottom bracket.
Install your seaport housing into the head tube port, pushing until it exits near the lower cable port access hole.
Use your finger to help push the housing around the bend in the frame up into the seat tube.
While pushing the housing into the head tube port, continue pushing the cable up the seat tube through the access port until the housing exits the seat tube.

PARK TOOL SETUP

Remove the lower cable port access cover with a 3mm Allen key.
Drop a Park Tool Router tool down the seat tube until it exits the access port.
Push your seaport housing into the frame from the headtube port until it exits near the access port.
Outside of the access port, connect the Park router tool to the housing.
Pull router tool back through the frame until your housing exits the seat tube.
HYDRAULIC SETUPS
Route a section of shifter housing through the frame using the steps described in Standard Setups. Connect the double-barb to the shifter housing and the seaport housing at the seat tube.
BRAKE Push the brake line into the frame starting at the rear triangle, feeding it forward to the ports into the front triangle and out the head tube.
At the same time, pull the shifter housing out of the head tube port while pushing the seat post housing into the seat tube until the double barb exits the head tube.
SHIFTER Push the shifter housing into the lower head tube port on the non-drive side. Feed the housing back to the ports on the rear triangle and eventually out near the drive-side dropout.

SWITCH INFINITY SERVICE

With a 5mm Allen wrench, remove the main pivot Collet Wedge Bolt
With a 10mm Allen wrench, remove the Main Pivot Collet Axle. The Collet Nut on the drive side can remain in the frame.
Rotate your swingarm upwards to access both grease zikrs and expose the whole Switch Infinity link. With a clean rag and mild detergent, clean any mud, dust, or debris off the Switch Infinity Link.
Using a needle-type grease gun, push new grease into the two Switch Infinity grease ports until you see grease extruding from the shaft seals.
Wipe off any excess grease that was pushed out of the seals.
Lower the swingarm and re-install your Main Pivot Collet Bolt prepped with Blue 243 Loctite.
- Torque 11 Nm
Install the Main Pivot Collet Wedge and *Torque to 14 Nm.

FRAME ASSEMBLY

YETI TIPS
Make sure your tools are in good condition. A worn Allen key can round the hex on a bolt not allowing for proper torque. Torque settings are listed throughout the instructions. It is important to prep all bolt threads. The instructions denote whether to use a Loctite compound or grease.
Warning: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti Dealer

TOOLS NEEDED

3mm Allen key
4mm Allen keys
5mm Allen keys
6mm Allen key
10mm Allen key
Guide pin tool (Or two)
Cassette tool
Torque wrench
Grease
Blue (243) Loctite

All the parts you’ll need to get your SB140/LR frame assembled. Please refer to the exploded view later in this manual for more information
Press the Shock Eyelet Spacer into the rear shock eyelet using an arbor press or vise.
Apply a light coat of grease to the threads of the Rear Triangle at the Seat Stay Pivots. Install 2x Bearing Locking (200020311) with a cassette tool.
- Torque to 20 Nm.
Slide 4x Washer (300030214) over 4x M6 Cap Screw (300030057) prepped with Blue Loctite 243. Insert the 4x Cap Screws into the frame and place a black Infinity Link washer on each bolt. Orient the washers such that the flat surfaces are facing the window in the frame where the Switch Infinity Link is mounted.
Install the Switch Infinity Link into the frame by rocking it into place over the bolts and black Switch Washers. The grease zikrs should face the non-drive side. Tighten the 4x bolts by hand, then torque in a cross pattern2
Grease shaft of the Link Pivot Female Bolt (200020328). Place the Link onto the Front Triangle as shown and secure with link Pivot female Bolt
Install Male Link Pivot Bolt (300030293) prepped with Blue Loctite 243 into Link Pivot Female Bolt (200020328) as shown.
- Torque to 15 Nm.
Apply a light coat of grease to the inner surfaces of 2x Extender Bearing Races (300040505). Place one each into the Upper and Lower Shock Extenders (200020322 and 200020323). Place the Upper and Lower Extenders together so that the bearings touch in the middle. Orient the Upper threaded extender toward the top and slide into Link (200020321). Secure with a Guide Pin.
Slide a 41mm Titanium Female bolt with Washer (300030069) through the Link/Extender Assembly. Secure with a It Male Bolt (300030151) & Washer (300030062) prepped with Blue Loctite 243.
- Torque to 10 Nm.
Apply a light coat of grease to the Rear Triangle in the Main Pivot bores and grease shaft of Main Pivot Collet Axle (300040485) and prep threads with Blue Loctite 243. Slide the Rear Triangle over the Switch Infinity Link and install Main Pivot Collet Axle (300040485) through assembly. Install Collet Nut (300030285) and tighten Axle until any play is removed.
- Torque to roughly 12 Nm
Grease threads and wedge of Large Collet Wedge Bolt (300040454). Install into the Main Pivot Axle.
- Torque to 14 Nm
Grease shaft of 2x Seat stay Pivot Female Bolt (200020326) . Install one Seat stay Pivot Female Bolt (200020326) through the Rear Triangle and into the link
Rotate Swingarm Forward and move Upper and Lower Shock Extenders out of the way. Install one Keyed Bolt (200020327) prepped with Blue Loctite 243 from the inside of the link, threading the Female Bolt onto it. Draw the Keyed Bolt into assembly and make sure its key nests into the keyway on the Link bore Repeat process on opposite side.
- Torque to 16 Nm
Open the Upper and Lower Shock Extenders and position the Shock into the frame, allowing it to sit between the two Extender jaws. Secure front eyelet with a Guide Pin
Grease shaft of short Collet Axle (300030296) and prep threads with Blue Loctite 243. Install from the Lower Extender through the Shock and threading into the Upper Extender.
- Torque to 13 Nm
Grease threads and wedge of small Collet Wedge Bolt (300040486) and install into short Collet Axle.
- Torque to 8 Nm.
Install 45mm Titanium Female Bolt (300030297) with Washer (300030069) through the front shock mount
Secure front shock mount with Titanium Male Bolt (300030151) prepped with Blue Loctite 243 and Washer (300030062).
- Torque to10 Nm
Install 2x Washer (300030148) onto 2x H20 Bolt (300030010) and grease threads. Install into front triangle and secure hand tight .
- Torque to roughly 4 Nm.
Install Cable Port Cover (300040454) onto frame with 2x Fled Head Bolt (300030299).
- Torque to 3-4 Nm
Grease outer surface of Derailleur Hanger (300060073). Install into Rear Triangle and secure with Hanger Cap (300060075). NOTE: HANGER IS REVERSE THREADED
- Torque to 10 Nm

FOX TRANSFER POST INSERTION GUIDE

YETI-SB140-Mountain-Bicycle-25 YETI-SB140
-Mountain-Bicycle-26

EXPLODED VIEW PARTS LIST

| | | |    ITEM# **| PART #| DESCRIPTION| QTY
---|---|---|---|---|---|---|---
   ITEM# **| PART #| DESCRIPTION| QTY|      4.12| 300030285| COLLET NUT M15 X 1.5| 1
        1 **| N/A **| SB140 FRONT TRIANGLE ASSEMBLY| | 4.13| 300030296| COLLET AXLE 30.5 X 10.5 M10 X 1.0| 1
      1.1| N/A| SB140 FRONT TRIANGLE| 1|      4.14| 300040486| COLLET WEDGE SUB-ASSEMBLY 10 MM| 1
      1.2| 300070006| ICE AXE HEAD BADGE| 1|     4.14.1| 300030284| COLLET BOLT M5 X .8| 1
      1.3| 400100186| DT PROTECTOR| 1|     4.14.2| 300030283| COLLET WEDGE 10MM| 1
        2 **| N/A **| SB140 SWING ARM ASSEMBLY **| 1|     4.14.3| 300040482| SPIRAL RETAININ G RING 0.25 X 0.22 INCHES| 1
      2.1| N/A| SB140 SWING ARM| 1|      4.15| 30003029 7| BOLT MASTER, TI FEMALE, 8 X 45.0| 1
      2.2| 400100198| SB140 PROTECTOR CS/SS| 1|      4.16| 300030298| BOLT MASTER, TI FEMALE, 8 X 41.0| 1
      2.3| 400100199| SB140 PROTECTOR CS – LOWER| 1|      4.17| 300030069| WASHER 8.5 X 12.5 X 0.5 MM| 2
       3 **| N/A **| SB140 S H OCK A SSE M B LY| 1|      4.18| 300030151| BOLT, TI MALE, M6 X 12.0 MM| 2
       4 **| N/A **| SB140 S MALL P A RTS A SSE M B LY**| 1|      4.19| 300030062| WASHER 6.5 X 12.5 X0.5 MM| 2
      4.1| N/A| SB140 LINK SUB-ASSEMBLY| 1|      4.20| 200020322| ASSEMBLY SHOCK EXTENDER TOP (60MM)| 1
     4.1.1| 300040507| SB140 LINK| 1|     4.20.1| 300040502| SHOCK EXTENDER TOP (60MM)| 1
     4.1.2| 300020052| BEARING 6902-2RS EXTENDED, 15 X 28 X 7/10| 2| 4.20.2| 300020032| BEARING, 398 MAX DBL, 8X19X10/11| 1
      4.2| 200020326| BOLT, SS PIVOT, FEMALE| 2|      4.21| 200020323| ASSEMBLY SHOCK EXTENDER, BOTTOM (60MM) 1
      4.3| 20002032 7| LINK PIVOT HARDWARE, KEYED, LONG| 2|     4.21.1| 300040503| SHOCK EXTENDER BOTTOM (60MM)| 1
      4.4| 200020311| LOCKRING, 6902-2RS| 2|     4.21.2| 300020032| BEARING, 398 MAX DBL, 8X19X10/11| 1
      4.5| 300030293| LINK, PIVOT HARDWARE, MALE, 15MM| 1|      4.22| 300040505| SHOCK EXTENDER BEARIN G EXTENSION| 2
      4.6| 200020328| STUD, LINK BEARING, FEMALE, 15MM| 1|      4.23| 300060078| ASSEMBLY YETI SEAT CLAMP – BOLT ON 31.6| 1
      4.7| 200020201| SWITCH INFINITY G1 MECHANISM| 1|     4.23.1| N/A| COLLAR, BOLT ON, YETI SEAT CLAMP, 31.6| 1
      4.8| 300030057| BOLT, M6 X 1.0, 20L| 4|    4.23.2| N/A| BARREL NUT, YETI SEAT CLAMP, BOLT ON| 1
      4.9| 300030214| WASHER 6.3X10X1 MM| 4|     4.23.3| 300030010| BOLT, M5 X 0.8, 16L| 1
     4.10| 300040485| COLLET AXLE 15MM| |      4.24| 300040504| CABLE PORT COVER| 1
     4.11| 300040454| COLLET WEDGE SUB-ASSEMBLY 15MM| 1|      4.25| 300030299| BOLT, FLAT HEAD, M5 X 0.8 X 16| 2
    4.11.1| 300030268| COLLET BOLT M8 X 1.25| 1|      4.26| 300020052| BEARING 6902-2RS EXTENDED, 15 X 28 X 7/10| 2
   4.11.2| 300030267| COLLET WEDGE 15MM| 1|      4.27| 300030010| BOLT, M5 X 0.8. 16L| 2
   4.11.3| 300040450| SPIRAL RETAININ G RING 0.37 X 0.349 INCHES| 1| 4.28| 300030148| WASHER 5.1 X 8.9 X 1.0 MM| 2
| | | |      4.29| 300030300| SHOCK EYELET SPACER| 1
| | | |      4.30| 300060073| 12 X 148 HANGER KIT G3| 1
29.| | | | | | | 30.

__ PART # DESCRIPTION QTY

200020333 SB140 MA STER REB U I LD KIT ****
200020311 LOCKRING, SS PIVOT 2
200020322 SHOCK EXTENDER 60MM TOP W/BEARIN G 1
200020323 SHOCK EXTENDER 60MM BOTTOM W/BEARIN G 1
200020326 BOLT, SS PIVOT, FEMALE 2
200020327 LINK PIVOT HARDWARE, KEYED, LONG 2
200020328 STUD, LINK BEARING, FEMALE 15MM, 48.5L 1
300020045 BEARING F6902 2RS 28X15X 7 OUT 2
300020052 BEARING 6902 LLU MAX-E 4
300030057 BOLT CAP M6X1X20 4
300030062 WASHER SS 6.5MM ID 12.5MM 2
300030069 WASHER SS 8.5MM ID 12.5MM 2
300030151 BOLT-TI-MALE M6X12MM 2
300030214 WASHER 10 X 6.2 X 1 4
300030285 COLLET AXLE NUT M15X1.5X12 1
300030293 AXLE, MALE, 15MM X 16MM, M10X1.0 1
300030296 COLLET AXLE 30.5X10.5 M10X1.0 1
300030297 BOLT MASTER, TI FEMALE, 8 X 45.0 1
300030298 BOLT MASTER, TI FEMALE, 8 X 41.0 1
300030299 BOLT, FLAT HEAD, M5 X 0.8 X 16 2
300030300 SHOCK EYELET SPACER 1
300040454 COLLET-WEDGE ASSEMBLY GEN2 1
300040485 AXLE COLLET 15X52.5SX13T 1
300040486 COLLET-WEDGE ASSEMBLY – M10 1
300040504 CABLE PORT COVER 1
300040505 SHOCK EXTENDER BEARIN G EXTENSION 2

200020334	S B140 HA R DWA RE KIT
200020311	LOCKRING, SS PIVOT

200020335 SB140 BE ARING REBUILD KIT
300020032 BEARING 398 2RS MAX DBL ROW 2
300020045 BEARING F6902 2RS 28X15X 7 OUT 2
300020052 BEARING 6902 LLU MAX-E

REBUILD KITS CONTINUED

PART # 200020039 DESCRIPTION SB140 PORT COVER KI QTY

__300030299 BOLT, FLAT HEAD, M5 X .08 X 16 2
300040504 CABLE PORT COVER 1
400100196 SB140 GEN1 PROTECTOR KIT ****
400100186 UNIVERSAL DT PROTECTOR 1
400100198 SB140 CS/SS PROTECTOR 1
400100199 SB140 CS LOWER PROTECTOR 1

LIFETIME WARRANTY

HERE’S EVERYTHING YOU NEED TO KNOW ABOUT OUR LIFETIME WARRANTY:
All 2019 (or newer) frames, including the Switch Infinity, are covered for life against damage due to manufacturing defects for the original purchaser. Paint and finish are covered for 1-year. We will repair or replace, at our discretion, any frame we deem defective. There are a few conditions: you must register it online at yeticycles.com and you must take it to an authorized Yeti Cycles dealer for processing. Warranty does not cover damage due to ordinary wear and tear, neglect or intentional destruction. From a slingshot or your truck. If you happen to have a crash or non-warranty situation, we’ll get you back on the trail with a reasonable replacement price. Same conditions as above. Lifetime Warranty applies to all 2019 and newer frames (including the SB100). Model year 2018 and older frames will be covered under our previous warranty (5-year or 2-year based on time of purchase). Simple as that. No fine print.

DISCLAIMER
YETI Cycles is not responsible for any damages to you or others arising from riding, transporting or other use of your bicycle. In the event that your frame breaks or malfunctions, YETI Cycles shall have no liability or obligation beyond the repair or replacement of your frame pursuant to the terms outlined in the warranty.