YETI CYCLES SB140-LR Mountain Bike Owner’s Manual

October 30, 2023
Yeti Cycles

YETI-logo

YETI CYCLES SB140-LR Mountain Bike

YETI-CYCLES-LR-Mountain-Bike-product-image

YETI SB140/LR OWNER’S MANUAL

Overview
The YETI SB140/LR is a high-performance mountain bike designed to deliver an exceptional riding experience. The bike is equipped with patented Switch Infinity technology, a high modulus carbon fiber main frame and swingarm, and other advanced features that provide efficient pedaling performance and smooth support on rough terrain.

Frame Features

  • Switch Infinity Technology Patented Suspension System: The SB140 delivers 140mm of rear travel with our patented Switch Infinity technology. Efficient pedaling performance while still smooth and supportive when the going gets rough.
  • High Modulus Carbon Fiber Main Frame and Swing Arm: High modulus carbon is hand laid to create our Turq Series frames. That same stiffness and efficiency can also be found in our carbon series frame sets.
  • Floating Collet Axle System on Pivots Increases Bearing Life: Floating collated pivot axles help create a perfectly aligned connection between the front and rear triangles of the frame. Allowing the enduro max sealed bearings to keep things moving freely at the pivots.
  • Integrated ISCG-05 Mounts: 3-bolt ISCG-05 chain guide mounts are there for you in case you need extra drivetrain security for rowdy sections.
  • Rattle-Free Cable Port Assembly Secures Cables and Hoses to Provide a Silent Ride: The SB140 is designed with clamping cable ports to insure a quite ride, reduced cable movement and clean aesthetic. The ports are configurable so you can chose cable or wireless components without leaving behind open housing ports.
  • Internally Molded Cable Tubes for Hassle-Free Routing and a Quiet Bike: Gone are the days of fishing your cables through your downtube hoping they pop out the other side. The SB140’s internally molded cable tubes allow you to put the cable in one port and have it come out right where you want it.

Frame Assembly
Before assembling your YETI SB140/LR, please review the owner’s manual and accompanying manuals for your bicycle. It is recommended that all service and repairs be performed by an authorized Yeti Dealer to ensure proper assembly and maintenance. Follow the steps below to assemble your bike:

  1. Remove the bike frame from the packaging.
  2. Attach the front fork to the frame using the appropriate tools and torque specifications.
  3. Install the handlebar, stem, and seatpost according to the manufacturer’s instructions.
  4. Install the wheels and tires, ensuring proper inflation and alignment.
  5. Check all bolts and fasteners for proper torque using a torque wrench.
  6. Test ride the bike to ensure proper function and performance.

Maintenance
To ensure optimal performance and longevity of your YETI SB140/LR, regular maintenance is required. Follow these guidelines to maintain your bike:

  • Clean the bike after every ride using a soft brush and mild soap.
  • Check tire pressure before each ride and adjust as needed.
  • Check bolts and fasteners regularly for proper torque.
  • Inspect suspension components regularly for signs of wear or damage.
  • Replace worn or damaged components as needed.

For more detailed maintenance instructions, refer to the owner’s manual and accompanying manuals for your bicycle.

CONGRATULATIONS ON YOUR PURCHASE OF A NEW YETI.
We are confident your new bicycle will exceed your expectations for value, performance, and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience. Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun.
This model specific manual is designed to be used in conjunction with the general Yeti Owner’s Manual and the manuals supplied by the suspension manufacturers. If you did
not receive the Yeti Owner’s Manual or the manual provided by the suspension manufacturer, download the materials off the Internet, or contact your local dealer. Bicycling can be
a hazardous activity even under the best of circumstances. Proper maintenance of your bicycle is your responsibility and when done properly helps reduce the risk of injury and damage to your bicycle.
This manual outlines basic setup and maintenance recommendations of your new Yeti. It is impossible to anticipate every situation or condition that may occur during the assembly,
setup, and maintenance of your bicycle, Yeti recommends that all service and repairs be performed by your local authorized Yeti Dealer.
This manual contains many “Warnings” and “Cautions” concerning the consequences of failure to maintain or inspect your bicycle. The word “Warning” indicates a potentially hazardous situation in which, if not avoided, could result in serious injury or death.
The word “Caution” indicates a potentially hazardous situation in which, if not avoided may result in minor injuries or damage to your bicycle or a component of your bicycle.
Be sure to read and understand all of the Warnings and Cautions listed in the manual.

WARNING: Make sure you review and understand the warnings, instructions, and content of this manual and accompanying manuals for your bicycle.
WARNING: Technological advances have made bicycles and bicycle components more complex and the pace of innovation is increasing. It is impossible for this manual or the accompanying manuals to provide all the information required to properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Yeti retailer.

THE LOWDOWN ON THE SB140/LR AND ITS FEATURES.

FRAME FEATURES

  1. SWITCH INFINITY TECHNOLOGY PATENTED SUSPENSION SYSTEM
    The SB140 delivers 140mm of rear travel with our patented Switch Infinity technology. Efficient pedaling performance while still smooth and supportive when the going gets rough.

  2. HIGH MODULUS CARBON FIBER MAIN FRAME AND SWING ARM
    High modulus carbon is hand laid to create our Turq Series frames. That same stiffness and efficiency can also be found in our carbon series frame sets.

  3. FLOATING COLLET AXLE SYSTEM ON PIVOTS INCREASES BEARING LIFE
    Floating collated pivot axles help create a perfectly aligned connection between the front and rear triangles of the frame. Allowing the enduro max sealed bearings to keep things moving freely at the pivots.

  4. INTEGRATED ISCG-05 MOUNTS
    3-bolt ISCG-05 chain guide mounts are there for you in case you need extra drivetrain security for rowdy sections.

  5. RATTLE-FREE CABLE PORT ASSEMBLY SECURES CABLES AND HOSES TO PROVIDE A SILENT RIDE
    The SB140 is designed with clamping cable ports to insure a quite ride, reduced cable movement and clean aesthetic. The ports are configurable so you can chose cable or wireless components without leaving behind open housing ports.

  6. INTERNALLY MOLDED CABLE TUBES FOR HASSLE-FREE ROUTING AND A QUIET BIKE
    Gone are the days of fishing your cables through your downtube hoping they pop out the other side. The SB140’s internally molded cable tubes allow you to put the cable in one port and have it come out right where you want it.

  7. INTEGRATED 41MM / 52MM TAPERED HEAD TUBE
    Using an integrated head tube design on the SB140 allows for a larger head tube with more area, which results in increased stiffness, and lower overall ride height without compromising any performance.

  8. CUSTOM DOWN TUBE PROTECTOR AND RIBBED CHAIN GUARDS TO DECREASE CHAIN SLAP NOISE
    Custom seatstay, chainstay and down tube guards keep the ride quiet while protecting the frame. The nylon down tube guard keeps your bike protected where you need it most so you can focus on charging down the trail.

  9. INTEGRATED AXLE AND UNIVERSAL DERAILLEUR HANGER SYSTEM
    Dedicated 12 x 148 boost dropouts with SRAM’s universal derailleur hanger (UDH) provide strength, stiffness and easy hanger and wheel installation.

  10. CUSTOM TUNED REAR SHOCK
    We develop custom suspension tunes from the ground up here in Golden, CO to optimize suspension performance to perfectly compliment the SB140 suspension kinematics. For help setting up your suspension, please visit our Shock Setup Guide. https://shocksetup.yeticycles.com/bikes

GEOMETRY SB140 LR

YETI-CYCLES-SB140-LR-Mountain-Bike-2

F I T

  • SMALL 5’1” (155 CM) – 5’7” (170 CM)
  • MEDIUM 5’5″ (165 CM) – 5’11” (180 CM)
  • LARGE 5’10” (178 CM) – 6’3″ (191 CM)
  • X-LARGE 6’1” (185 CM) – 6’7” (200 CM)
  • XX-LARGE 6’5″ (195 CM) – 6’11” (210 CM

| 160MM FORK| SM| MD| LG| XL| XXL
---|---|---|---|---|---|---
A| SEAT TUBE LENGTH| 365| 400| 440| 470| 485
B| EFF. TOP TUBE LENGTH| 573| 603| 624| 652| 671
C| HEAD TUBE ANGLE˚| 65.0| 650| 65.0| 65.0| 65.0
D| EFF. SEAT TUBE ANGLE˚| 77.0| 77.0| 77.0| 77.0| 77.0
E| ACTUAL SEAT TUBE ANGLE| 71.8| 72.2| 72.4| 72.8| 73.3
F| CHAINSTAY LENGTH| 436| 438| 440| 442| 444
G| WHEELBASE| 1188| 1221| 1246| 1277| 1304
H| ESTIMATED BB HEIGHT| 342| 342| 342| 342| 342
I| STANDOVER| 726| 733| 737| 739| 744
J| HEADTUBE LENGTH| 92| 95| 100| 112| 134
K| FORK (AXLE TO CROWN)| 575| 575| 575| 575| 575
L| FORK (OFFSET)| 44| 44| 44| 44| 44
M| STACK| 617| 620| 625| 635| 655
N| REACH| 430| 460| 480| 505| 520
O| FRONT CENTER| 752| 783| 806| 835| 860
P| VERTICAL FORK TRAVEL| 145| 145| 145| 145| 145

YETI-CYCLES-SB140-LR-Mountain-Bike-4

F I T

  • SMALL 5’1” (155 CM) – 5’7” (170 CM)
  • MEDIUM 5’5″ (165 CM) – 5’11” (180 CM)
  • LARGE 5’10” (178 CM) – 6’3″ (191 CM)
  • X-LARGE 6’1” (185 CM) – 6’7” (200 CM)
  • XX-LARGE 6’5″ (195 CM) – 6’11” (210 CM)

| 150MM FORK| SM| MD| LG| XL| XXL
---|---|---|---|---|---|---
A| SEAT TUBE LENGTH| 365| 400| 440| 470| 485
B| EFF. TOP TUBE LENGTH| 571| 602| 623| 650| 670
C| HEAD TUBE ANGLE˚| 65.4| 65.4| 65.4| 65.4| 65.4
D| EFF. SEAT TUBE ANGLE˚| 77.5| 77.5| 77.5| 77.5| 77.5
E| ACTUAL SEAT TUBE ANGLE| 72.2| 72.6| 72.8| 73.2| 73.7
F| CHAINSTAY LENGTH| 436| 438| 440| 442| 444
G| WHEELBASE| 1184| 1217| 1242| 1273| 1300
H| ESTIMATED BB HEIGHT| 339| 339| 339| 339| 339
I| STANDOVER| 722| 729| 733| 735| 740
J| HEADTUBE LENGTH| 92| 95| 100| 112| 134
K| FORK (AXLE TO CROWN)| 565| 565| 565| 565| 565
L| FORK (OFFSET)| 44| 44| 44| 44| 44
M| STACK| 614| 617| 621| 631| 651
N| REACH| 435| 465| 485| 510| 525
O| FRONT CENTER| 748| 779| 802| 831| 856
P| VERTICAL FORK TRAVEL| 136| 136| 136| 136| 136

YETI-CYCLES-SB140-LR-Mountain-Bike-6

KEEP YOUR YETI FRESH AND CLEAN

MAINTENANCE OVERVIEW
Following these guidelines will help maintain the performance of your bicycle and prevent more serious problems from arising. It is important to remember that service intervals can vary depending on climate, trail conditions and riding frequency. Servicing your bike requires special knowledge and tools. If you are unsure about working on your own bicycle, contact your authorized Yeti Dealer for more information on general bicycle maintenance.

TORQUE
Yeti strongly recommends using a torque wrench when assembling your frame. Torque specifications for individual parts on the SB140 are listed below, as well as in the step by step assembly instructions later in the manual. For general bicycle maintenance please consult the torque specifications of the component you are adjusting.

YETI-CYCLES-SB140-LR-Mountain-Bike-7

KEY TORQUE SPECS

ITEM # DESCRIPTION TORQUE (NM)
300030361 COLLET AXLE, 15MM X 58.5L, M15X1.5 25
300030364 SHOULDER SCREW, 15 X 27.35L, M15 THREAD, SS PIVOT 25
300030376 COLLET AXLE 15MM, 43.5L 25
300030378 COLLET WEDGE SUB-ASSUMBLY 15MM, M4 THREADED WEDGE BOLT 14
300040486 COLLET WEDGE SUB-ASSEMBLY 10MM 8
300030057 SHCS, M6 X 1.0, 20L 12
300030296 COLLET AXLE M10X1.0, 30.5L X 10.5T 15
300030370 SCREW, MALE, M6X12.0MM 10
300030174 SCREW, FH, M4 X 0.7, 16L 2.5
300030177 SCREW, FH, M4 X 0.7, 25L 2.5
300030357 SHCS, LOW PROFILE, M5 X 0.8, 16L 5
300030173 SCREW, FH, M4 X 0.7, 10L 2.5
300060080 SRAM UNIVERSAL HANGER 25
100425018 REAR AXLE M12X1 X 172L BOLT-ON BLACK UDH 15

FRAME ASSEMBLY

YETI TIPS
Make sure your tools are in good condition. A worn allen key can round the hex on a bolt not allowing for proper torque.
Torque settings are listed throughout the instructions and on page 8 of this manual. It is important to prep all bolt threads. The instructions denote whether to use
a Loctite compound or grease and part locations, listed in parentheses, are shown in the exploded view on page 18. Please ensure all prep call outs are followed.
WARNING: Failure to follow prep instructions could lead to serious frame issues.
WARNING: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti Dealer.

TOOLS NEEDED

  • Torque wrench(es), 5-25 Nm, CW and CCW Directions
  • 2.5mm allen key
  • 3mm allen key
  • 4mm allen key
  • 5mm allen key
  • 6mm allen key
  • 8mm allen key
  • 10mm allen key
  • 8mm guide pins
  • 3” socket extender
  • Blue Loctite (243)
  • Grease

YETI-CYCLES-SB140-LR-Mountain-Bike-9

  1. Press Shaft Eyelet Spacer (3.22) into rear shock eyelet.

  2. Install 2X Low Profile H20 Bolts (3.27) and Washers (3.28) to front triangle.
    Torque: 4 Nm (or hand tight)
    YETI-CYCLES-SB140-LR-Mountain-Bike-10

  3. Install 2x Cable Port Clamps (3.29) to the front triangle with 2x M4 x 10L FHCS (3.33).
    Install 1x Cable Port Clamp (3.29) to the
    rear triangle NDS Chainstay with 1x M4 x 10L FHCS (3.33).
    Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.

  4. Place a Head Tube Cable Port Cover (3.32) into each recess behind the head tube.
    Place a Double Port Clamp (3.30) into the non-drive side cover and a Single Port Clamp (3.31) into the drive-side cover. Secure with M4 x 25L FHCS (3.26).
    Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.
    YETI-CYCLES-SB140-LR-Mountain-Bike-11

  5. Install Lower DT Protector (3.36) to the front triangle using 3x Low Profile M5 Screws (3.27)
    Torque: 5 Nm

  6. Assemble Switch Infinity Link (3.13) into frame using 4x SHCS (3.11) with Washers (3.12). Grease zerks should face to the non-drive side.
    Torque in a cross pattern: 12 Nm.
    Repeat torque to ensure all fasteners fully tight.
    YETI-CYCLES-SB140-LR-Mountain-Bike-12

  7. Place 2x Race Extenders (3.5) onto the lower bearings in Link Assembly (3.16). Install into front triangle using Link Pivot Collet Axle (3.4) and plain Collet Nut (3.2).
    Torque: 25 Nm

  8. Assemble Upper (3.23) and Lower (3.22) Shock Extender to SB149 Link (3.16) by placing 2X Race Extender (3.15) in the extender cavities and sliding between the Link tabs. Threaded Extender (3.23) should be oriented to the top. Secure with a Guide Pin and assemble Female 8x41mm Bolt (3.17) with Washer (3.21) through the assembly. Secure with Male M6 Bolt (3.19) and Washer (3.20).
    Torque: 10 Nm

  9. Apply grease to main pivot cavities of Rear Triangle. Slide Rear Triangle Assembly onto main pivot and secure with Main Pivot Collet Axle (3.1) and Routing Collet Nut* (3.7), placing routing feature at the top.
    Torque: 25 Nm
    Install a plain collet nut (3.2, flat top with no clamp feature) if kit uses a wireless drivetrain.

  10. Place 2x Race Extenders (3.5) onto the upper bearings in Link Assembly (3.16). Rotate Rear Triangle and Link together, lining up SS Pivot bores.
    Install 2x SS Pivot Screws (3.3) from the inside of the Link and partially into the Rear Triangle.
    Place 2x plain Collet Nut (3.2) into the Rear Triangle.
    Using a wrench from the outside of the Swingarm, begin tightening in the “left-hand” direction (this is still a standard thread, but installed from the inside), tightening the SS Pivot Screw and Collet Nut.
    Torque: 25 Nm

  11. Install Large Collet Wedge Bolts (3.9) into 2x Collet Axles (3.1) and (3.4)
    Torque: 14 Nm
    QC CHECK
    Cycle rear triangle through to make sure motion is smooth.
    Take precaution to make sure link does not contact seat tube.

  12. Install the Shock into the frame by securing front eyelet with a Guide Pin. Install small Collet Axle (3.14) through the lower Extender (3.22), through the Shock, and thread into Upper Extender (3.23).
    Torque: 15 Nm
    Install Small Collet Wedge Bolt (3.10) into Axle.
    Torque: 8 Nm
    Take precautions to prevent the shock striking/contacting the downtube.

  13. Install Female 8x45mm bolt (3.18) with Washer (3.21) through front Shock Eyelet and secure with M6 Male Bolt (3.19) and Washer (3.20).
    Torque: 10 Nm

  14. Install Housing Clamp Cap (3.8) onto the drive-side main pivot axle with a M4 x 16L FHCS (3.25).
    Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.

  15. Install a Housing Clamp Cap (3.8) and Clamp Base (3.6) onto the non-drive main pivot wedge bolt with a M4 x 25L FHCS (3.26).
    Tighten until snug. Hardware can be torqued to 2-3 Nm after housing installation.

  16. Install Univesal Hanger (3.34) into frame. Do not use grease. Note that hanger cap bolt is reverse threaded.
    Torque: 25 Nm
    Check all frame bolts to ensure that no linkages are loose and there is proper fit on all components.

BEARING PRESS ASSEMBLY

LINK BEARING PRESS

  1. Press both upper bearings into the link from the inside of the link tabs using a 15x24mm arbor. Check that both bearings are fully seated.
  2. Press the drive-side lower bearing into the link using a 15x24mm arbor, fully seating the bearing into the link.
  3. Install the lower bearing spacer against the pressed lower bearing. Press the non-drive side bearing into the link until bearing bottoms against the spacer

EXTENDER BEARING PRESS

  1. Press the bearing into the upper extender with the extended race facing out of the bore. Press into the extender until fully seated.
  2. Press the bearing into the lower extender with the extended race facing out of the bore. Press into the extender until fully seated.

SWITCH INFINITY V2 BEARING ASSEMBLY

BEARING REMOVAL

  1. Remove dust caps on the outside of the bearings. Remove non-drive side bearing.
  2. Remove axle sleeve from drive side bearing. Remove drive side bearing.

BEARING INSTALL

  1. Press drive side bearing into Switch Infinity body.
  2. Slide axle sleeve into drive side bearing.
  3. Press non-drive side bearing onto sleeve.
  4. Replace bearing caps.

SWITCH INFINITY V1 BEARING ASSEMBLY

BEARING REMOVAL

  1. Remove drive side bearing and axle sleeve
  2. Remove non-drive side bearing

BEARING INSTALL

  1. Press non-drive side bearing into switch infinity housing (ensure extended race is facing outward from switch infinity body).
  2. Place axle sleeve in body and press drive side bearing into housing

SEAT POST SET-UP

STANDARD ROUTING SET-UP

  1. With a 3mm allen wrench, remove the outer plastic downtube protector.

  2. Install your seatpost housing into the drive-side head tube port, pushing until it exits near the downtube cable port access hole.

  3. The hole under the downtube protector provides an access point to use your finger to help push the housing around the bend in the frame up into the seat tube.

  4. While pushing the housing into the head tube port, continue guiding the cable up the seat tube through the access hole until the housing exits the seat tube.

SWITCH INFINITY SERVICE

  1. With a 2.5mm allen wrench, remove the two clamps securing the shifter and brake housing to the main pivot.

  2. With a 5mm allen wrench, remove the main pivot Collet Wedge Bolt (3.9).

  3. With a 10mm allen wrench, remove the Main Pivot Collet Axle (3.1).

  4. Rotate your swingarm upwards to expose the Switch Infinity Link and access both grease zerks. With a clean rag and mild detergent, clean any mud, dust, or debris off the Switch Infinity Link.

  5. Remove the two dust caps from the Switch Infinity Link. Clean any debris or dust off the dust caps and bearing races in the Switch Infinity Link. Reinstall dust caps when finished.

  6. Using a needle-type grease gun, push new grease into the two Switch Infinity grease ports until you see fresh grease extruding from the shaft seals. Wipe off any excess grease that was pushed out of the seals.

  7. Apply assembly grease to the Main Pivot Collet Axle (3.1) shaft and head and apply anti-seize to the threads. Lower the swing arm and re-install your Main Pivot Collet Axle (3.1). Torque: 25 Nm.

  8. Apply assembly grease to the Main Pivot Collet Wedge head and threads. Install into the Main Pivot Collet Axle (3.1). Torque: 14 Nm.

  9. Re-install the housing clamps at the main pivot. Place a single clamp onto the shifter housing and secure with a M4 x 16L screw. Place a clamp and clamp base around the brake housing and secure with a M4 x 25L screw. Tighten until snug.

DROPPER POST INSERTION GUIDE

Droppers are an essential tool for the modern mountain bike but proper clearance checks are required before heading out for your first ride.
The key checks are as follows:
Ensure your dropper is short enough to fit into the seat tube without interfering with the frames structure but you are still able to achieve your desired BB-Saddle measurement. See the max insertion depth chart to confirm this distance for wired and wireless posts.
There are some scenarios where you can fit a longer dropper in your frame but when you drop your dropper the saddle or battery for AXS posts could interfere with your tire during a suspension compression. See the Min BB-Saddle at full drop to confirm this distance.
Always perform a final check to ensure your post is installed to at least the minimum insertion line. Also, compress the dropper and suspension, let the air out of your shock, to ensure there is no tire interference to the saddle or AXS battery at full bottom out.
We strive to spec out dropper lengths to provide the maximum drop for the highest percentage of our riders. There is a wide range of saddle heights for every frame size. There is a possibility saddle height could fall outside of this range. A small percentage
of customers might find they require a shorter or longer post given their saddle height.
Please ensure you check the minimum dimensions in the below tables before going for your first ride. Failure to do so could result in tire to saddle rub or tire to battery contact for AXS posts.
Please confirm both of these measurements, they are both required to ensure proper dropper fitment.
If you have any questions, please contact Yeti or your local bike shop.

MINIMUM **BB TO SADDLE CABLED DROPPER (MM)***

FRAME SIZE| X-SMALL| 498.5
SMALL| 497.4
MEDIUM| 496.5
LARGE| No min
X-LARGE| No min
XX-LARGE**| No min

*These measurements are only for cabled droppers. Please make sure if you have a wireless post you confirm that there is not any interference of the tire hitting the battery when the post is fully dropped and the suspension is fully compressed.
**If you go lower then listed minimum you run the risk of tire to saddle interference.

MAX INSERTION WIRELESS DROPPER **(MM)***

FRAME SIZE| X-SMALL| 232.2
SMALL| 242.8
MEDIUM| 277.4
LARGE| 316.8
X-LARGE| 331.0
XX-LARGE| 331.0

*Subtract 34mm for a cabled dropper to accommodate housing bend angle.

EXPLODED VIEW

YETI-CYCLES-SB140-LR-Mountain-Bike-035

YETI-CYCLES-SB140-LR-Mountain-Bike-37

EXPLODED VIEW PARTS LIST

ITEM : PART #:DESCRIPTION TORQUE (NM):  QTY

SB140 FRONT TRIANGLE ASSEMBLY 1

  • 1.1 SB140 FRONT TRIANGLE ASSEMBLY 1

SB140 SWINGARM ASSEMBLY 1

  • 2.1 SB140 SWINGARM 1
  • 2.2 Upper CS/SS Protector, 140 1
  • 2.3 Lower CS Protector, Shared 1

SB140 SMALL PARTS ASSEMBLY 1

  • 3.1 300030361 COLLET AXLE, 15MM X 58.5L, M15X1.5 25 1
  • 3.2 300030362 COLLET NUT, M15, 9.5 THICK, ROUND CAP 4
  • 3.3 300030364 SHOULDER SCREW, 15 X 27.35L, M15 THREAD, SS PIVOT 25 2
  • 3.4 300030376 COLLET AXLE 15MM, 43.5L 25 1
  • 3.5 300030365 RACE EXTENDER, 25 X 15.1 X 3.35 4
  • 3.6 300030366 CLAMP BASE, 23MM X 3.5T, BRAKE HOUSING 1
  • 3.7 300030367 COLLET NUT, M15 X 1.5, SHIFTER HOSE CLAMP 1
  • 3.8 300030368 CLAMP CAP, HOUSING 2
  • 3.9 300030378 COLLET WEDGE SUB-ASSEMBLY 15MM, M4 THREADED WEDGE BOLT 14 2
  • 3.10 300040486 COLLET WEDGE SUB-ASSEMBLY 10MM 8 1
  • 3.11 300030057 SHCS, M6 X 1.0, 20L 12 4
  • 3.12 300030214 WASHER 6.3 X10.0 X 1.0 MM 4
  • 3.13 200020422 ASSY, SWITCH INFINITY, MECHANISM, FACTORY SERIES 1
  • 3.14 300030296 COLLET AXLE M10X1.0, 30.5L X 10.5T 15 1
  • 3.15 300030375 SHOCK EXTENDER BEARING EXTENSION 2
  • 3.16 200020385 SB140 LINK ASSEMBLY 1
  • 3.16.1 300040539 SB140 LINK 1
  • 3.16.2 HNA00000BA0 0000000000 BEARING, 3802-2RS, 15 X 24 X 7 4
  • 3.14.3 300030369 SPACER, 15.2 X 17 X 7.3L 1
  • 3.17 300030372 BOLT, FEMALE, 8 X 41.0, M6 THREAD 1
  • 3.18 300030371 BOLT, FEMALE, 8 X 45.0, M6 THREAD 1
  • 3.19 300030370 SCREW, MALE, M6X12.0MM 10 2
  • 3.20 300030062 WASHER 6.5 X 12.5 X 0.5 MM 2
  • 3.21 300030069 WASHER 8.5 X 12.5 X 0.5 MM 2
  • 3.22 200020323 ASSY, SHOCK EXTENDER_60MM, BOTTOM 1
  • 3.22.1 300040503 SHOCK EXTENDER BOTTOM [60MM] 1
  • 3.22.2 300020032 BEARING, 398 MAX DBL, 8 X 19 X 10/11 1
  • 3.23 200020322 ASSY, SHOCK EXTENDER_60MM, TOP 1
  • 3.23.1 300040502 SHOCK EXTENDER TOP [60MM] 1
  • 3.23.2 300020032 BEARING, 398 MAX DBL, 8 X 19 X 10/11 1
  • 3.24 300030374 SHOCK EYELET SPACER 1
  • 3.25 300030174 SCREW, FH, M4 X 0.7, 16L 2.5 1
  • 3.26 300030177 SCREW, FH, M4 X 0.7, 25L 2.5 3
  • 3.27 300030357 SHCS, LOW PROFILE, M5 X 0.8, 16L 5 3
  • 3.28 300030358 WASHER 5.2 X 8.8 X 1.0 MM, STAINLESS ED BLACK 2
  • 3.29 300040518 COVER-CABLE PORT, SINGLE, RIGHT EXIT 3
  • 3.30 300040522 CLAMP, HT PORT DOUBLE, PA6 1
  • 3.31 300040521 CLAMP, HT PORT SINGLE, PA6 2
  • 3.32 300040524 CABLE PORT COVER, HEAD TUBE, 2 PIECE 2
  • 3.33 300030173 SCREW, FH, M4 X 0.7, 10L 2.5 3
  • 3.34 300060080 SRAM UNIVERSAL HANGER 25 1
  • 3.35 300060078 ASSY, YETI SEAT CLAMP, BOLT ON, 31.6 1
  • 3.36 200020418 DT GUARD, MY23 OUTER, PA/ABS 1
  • 3.37 300040523 COVER, HT PORT, BLIND, PA6 1
  • 3.38 300040542 COVER-CABLE PORT, BLANK, RIGHT EXIT 1
  • 3.39 300040510 FRAME PLUG, CABLE PORT 2
  • 3.40 100425018 REAR AXLE M12X1 X 172L BOLT-ON BLACK UDH 15 1

SB140 SHOCK SUB ASSEMBLY 1

REBUILD KITS

PART : DESCRIPTION : QTY

  • 200020435 LINK AND SHOCK EXTENDER BEARING REBUILD KIT HNA00000BA0
  • 0000000000 BEARING, 3802-2RS, 15 X 24 X 7 4
  • 300030369 SPACER, 15.2 X 17 X 7.3L 1
  • 300020032 BEARING, 398 MAX DBL, 8 X 19 X 10/11 2
  • 200020445 SWITCH INIFINITY V2 BEARING REBUILD KIT
  • 300020060 BEARING MR17287 LLU MAX BO 2
  • 300030383 SWITCH INFINITY V2 BEARING SPACER 1
  • 200020436 CABLE PORT KIT
  • 300030177 SCREW, FH, M4 X 0.7, 25L 3
  • 300040518 COVER-CABLE PORT, SINGLE, RIGHT EXIT 3
  • 300040522 CLAMP, HT PORT DOUBLE, PA6 1
  • 300040521 CLAMP, HT PORT SINGLE, PA6 2
  • 300040524 CABLE PORT COVER, HEAD TUBE, 2 PIECE 2
  • 300030173 SCREW, FH, M4 X 0.7, 10L 3
  • 300040523 COVER, HT PORT, BLIND, PA6 1
  • 300040542 COVER-CABLE PORT, BLANK, RIGHT EXIT 1
  • 300040510 FRAME PLUG, CABLE PORT 2
  • 300030366 CLAMP BASE, 23MM X 3.5T, BRAKE HOUSING 1
  • 300030368 CLAMP CAP, HOUSING 2
  • 300030367 COLLET NUT, M15 X 1.5, SHIFTER HOSE CLAMP 1
  • 300030174 SCREW, FH, M4 X 0.7, 16L 1
  • 200020437 NYLON DOWNTUBE PROTECTOR
  • 200020418 DT GUARD, MY23 OUTER, PA6 1
  • 300030357 SHCS, LOW PROFILE, M5 X 0.8, 16L 3
  • 200020438 SB140 PROTECTOR KIT
  • 200020406 CS/SS PROTECTOR, SB140 1
  • 200020405 CS PROTECTOR, LOWER 1
  • 200020419 DT GUARD, MY23 INNER, TPR 1
  • 200020421 SHOCK EXTENDER KIT
  • 300040543 SHOCK EXTENDER, SB140, 25MM 1
  • 300020032 BEARING, 398 MAX DBL, 8 X 19 X 10/11 2
  • 200020441 HARDWARE REBUILD KIT
  • 300030361 COLLET AXLE, 15MM X 58.5L, M15X1.5 1
  • 300030362 COLLET NUT, M15, 9.5 THICK, ROUND CAP 4
  • 300030364 SHOULDER SCREW, 15 X 27.35L, M15 THREAD, SS PIVOT 2
  • 300030376 COLLET AXLE 15MM, 43.5L 1
  • 300030365 RACE EXTENDER, 25 X 15.1 X 3.35 4
  • 300030366 CLAMP BASE, 23MM X 3.5T, BRAKE HOUSING 1
  • 300030367 COLLET NUT, M15 X 1.5, SHIFTER HOSE CLAMP 1
  • 300030368 CLAMP CAP, HOUSING 2
  • 300030378 COLLET WEDGE SUB-ASSEMBLY 15MM, M4 THREADED WEDGE BOLT 2
  • 300030057 SHCS, M6 X 1.0, 20L 4
  • 300030214 WASHER 6.3 X10.0 X 1.0 MM 4
  • 300030375 SHOCK EXTENDER BEARING EXTENSION 2
  • 300030369 SPACER, 15.2 X 17 X 7.3L 1
  • 300030377 SHOULDER SCREW, M10 X 23L, SHOCK EYELET 1
  • 300030372 BOLT, FEMALE, 8 X 41.0, M6 THREAD 1
  • 300030371 BOLT, FEMALE, 8 X 45.0, M6 THREAD 1
  • 300030370 SCREW, MALE, M6X12.0MM 2
  • 300030062 WASHER 6.5 X 12.5 X 0.5 MM 2
  • 300030069 WASHER 8.5 X 12.5 X 0.5 MM 2
  • 300030374 SHOCK EYELET SPACER 1
  • 300030174 SCREW, FH, M4 X 0.7, 16L 1
  • 300030177 SCREW, FH, M4 X 0.7, 25L 3
  • 300030357 SHCS, LOW PROFILE, M5 X 0.8, 16L 5
  • 300030358 WASHER 5.2 X 8.8 X 1.0 MM, STAINLESS ED BLACK 2
  • 300040518 COVER-CABLE PORT, SINGLE, RIGHT EXIT 3
  • 300040522 CLAMP, HT PORT DOUBLE, PA6 1
  • 300040521 CLAMP, HT PORT SINGLE, PA6 2
  • 300040524 CABLE PORT COVER, HEAD TUBE, 2 PIECE 2
  • 300030173 SCREW, FH, M4 X 0.7, 10L 3
  • 300040523 COVER, HT PORT, BLIND, PA6 1
  • 300040542 COVER-CABLE PORT, BLANK, RIGHT EXIT 1
  • 300040510 FRAME PLUG, CABLE PORT 2
  • 200020443 AXS CONVERSION KIT
  • 300040510 FRAME PLUG, CABLE PORT 2
  • 300040521 CLAMP, HT PORT SINGLE, PA6 1
  • 300030177 SCREW, FH, M4 X 0.7, 25L 1
  • 300030362 COLLET NUT, M15, 9.5 THICK, ROUND CAP 1
  • 300030358 WASHER 5.2 X 8.8 X 1.0 MM, STAINLESS 1
  • 300030173 SCREW, FH, M4 X 0.7, 10L 1
  • 200020444 FOX LINEAR BEARING V2 KIT
  • 200020422 FOX LINEAR BEARING V2 FACTORY 1
  • 300030057 SHCS, M6 X 1.0, 20L 4
  • 300030214 WASHER 6.3 X10.0 X 1.0 MM 4
  • FRAME PROTECTOR SHEET
  • 400100229 GLOSS
  • 400100230 MATTE
  • 200020354 FRAME PLUG CABLE PORT KIT
  • 400100202 SHUTTLE GUARD
  • 100425018 REAR AXLE M12X1 X 172L BOLT-ON BLACK UDH
  • 300060080 SRAM UNIVERSAL DERAILLEUR HANGER
  • 300030374 SHOCK EYELET SPACER

FREQUENTLY ASKED QUESTIONS (1 OF 2)

WHAT IS THE DIFFERENCE BETWEEN THE TURQ AND CARBON SERIES SB140?
TURQ Series bikes are manufactured with the highest quality and best- performing carbon fiber available and offer the perfect balance of stiffness, durability, and compliance. The result is a bike that feels smooth, solid and aggressive. Carbon series bikes use a modified carbon fiber layup of our TURQ Series bikes. By using different materials and tweaking the fiber layup, we are able to make a more aggressively priced carbon high-performance mountain bike while maintaining the strength and stiffness of its higher end sibling. The carbon series SB140 weighs a bit more, about 220g for a frame.

WHAT IS SWITCH INFINITY TECHNOLOGY AND HOW DOES IT WORK?
Switch Infinity utilizes a patented translating pivot that automatically switches direction as the bike moves through its travel. This provides excellent anti-squat characteristics for superior pedaling performance and ideal suspension characteristics as it gets deeper into the travel. Inside are a pair of greased bushings that slide up and down on two Kashima coated rails – it’s not an extra shock that needs to be filled with air. Just keep it greased and wiped clean per our maintenance recommendations below.

DOES THE SWITCH INFINITY SYSTEM REQUIRE MAINTENANCE?
The fully sealed Switch Infinity mechanism has external grease ports to lube the bushings and seals. Yeti and development partner Fox Racing Shox recommend a lubrication interval of 40 hrs of riding. It is important not to over lube the system and adhere to the recommended interval.
It also doesn’t hurt to wipe off any excess dust and dirt that may accumulate throughout the week. Any maintenance supplies you need can be found on our webstore or at your local dealer.
For detailed maintenance information, please visit
https://www.ridefox.com/fox17/help.php?m=bike&id=465

CAN I REPLACE OR MODIFY ANY YETI FRAME PARTS ON MY SB140?
All replacement frame parts for your SB140 can be found through your local dealer or on our webstore. Only genuine Yeti parts should be used when replacing any parts on your frame. We know there are a lot of aftermarket products out there that seem legit but we do not have the ability to qualify and ensure all of these products are safe to use on our frames. If it is found that any frame part has been modified or replaced all warranties will be voided and all liability will be assumed by the customer.

CAN I CHANGE OR UPGRADE THE SPEC COMPONENTS ON MY SB140?
There are many options in aftermarket parts to upgrade or personalize your bike. Some parts are standardized, especially from the big brands like Fox, Shimano, SRAM etc. You should always confirm with a professional mechanic that your parts are the correct standard and correctly and securely mount to your bike without any interference or play. Pay special attention to all the bikes standards and check the fit before use

CAN I USE AN ANGLESET ON THE SB140?
The SB140 was designed with an integrated headset which has the headset cups molded into the frame so you can easily drop the bearings into the cups. There are some aftermarket angle-sets available for this style headset however the frame was not tested for the use of these and therefore should not be used. Yeti’s warranty will be voided if it is found an angle set was installed on the frame and all liability will be assumed by the customer. See “What travel fork is the SB140 designed to use” for more information.

WHAT TRAVEL FORK IS THE SB140 DESIGNED TO USE?
The SB140 is designed to run a 150mm or 160mm travel fork. We tested this frame to 20mm over the spec fork. So if you’re feeling the need to beef up the fork you can run up to a 180mm fork no problem. Bottom line – max axle to crown measurement of 595mm. Increasing your fork travel will slacken the head angle and seat tube angle and raise the bottom bracket. Running a shorter fork is fine too if that suits you. Shortening the fork will steepen the head angle and seat tube angle and lower the bottom bracket For more geometry information, check out the geometry section.

HOW BIG OF A TIRE CAN I FIT ON THE SB140?
The short answer is the SB140 can accept up to a 2.6” tire. There is great tire clearance on the SB140 but tire sizes vary widely by manufacturers, so it is hard to give a number that works for all brands.

CAN I FIT A WATER BOTTLE INSIDE THE FRONT TRIANGLE?
Yes, we designed the SB140 to accommodate a standard sized water bottle inside the front triangle of sizes L-XXL with a piggy-back shock. Size SM and MD frames will fit a standard 21oz water bottle with a piggy-back shock. We recommend using a side-entry cage for easiest access.

WHAT CRANKS AND BOTTOM BRACKET CAN I USE ON THE SB140?
The SB140 bottom-bracket standard is BSA 73mm and only wide “q” factor cranks are compatible. It is readily compatible with Shimano, SRAM, and RaceFace cranks, but a fit
check is required for other brands.

WHAT REAR WHEEL AXLE FITS ON MY SB140?
The SB140 is designed to work exclusively with SRAM’s Universal Derailleur Hanger at 12x148mm spacing. This axle has a thread pitch 12×1.0 and a length of 172mm. Note that this axle is only compatible with frames specifically designed with the Universal Derailleur Hanger.

WHAT TYPE OF HEADSET DOES THE SB140 USE?
The SB140 uses an Integrated 41mm/52mm tapered headset. This system allows for the headset bearings to be contained inside the head tube for an overall lower ride height, more simplified installation, and increased stiffness.

HOW BIG OF A ROTOR WILL FIT ON THE FRAME?
The SB140 has a direct mount rear brake tab and can run a 180mm rotor without the need for
a brake adaptor. With the use of a brake adaptor the frame can accept up to a 203mm rotor.

CAN I RUN A STEALTH SEATPOST DROPPER ON THE SB140?
Yes. The SB140 has routing options for stealth only.

WHAT CHAINLINE WAS THE SB140 DESIGNED AROUND?
The SB140 was designed around a 55mm Boost chainline. Depending on the crank and chain ring configuration you can run other chainlines but you will have to do a clearance check first.

WHAT IS THE MAX SIZE SINGLE-CHAINRING THAT FITS ON THE SB140?
Without getting too technical, the max chainring size depends on the crank chainline and the chainring shape.

  • Shimano / SRAM 55mm chainline Boost cranks: 34t round / 32t oval
  • Minimum Chainring Size: 28t round / 30t oval

Confused? Ask your local dealer or call us 303.278.6909.

DOES THE SB140 HAVE ISCG MOUNTS?
Yes. The SB140 has integrated ISCG ’05 mounts. It is designed to work best with low-profile modern guides; depending on the brand, some older models with larger upper guides may not fit. We always recommend performing a fit-check with a specific chainguide to confirm compatibility.

WHAT TYPE OF SHOCK DOES THE SB140 USE?
The SB140 uses a 210 x 55mm shock. Depending on the shock model, it can be locked out but we recommend running it fully open for the best compliance and traction.

WHAT TYPE OF SHOCK HARDWARE DOES THE SB140 USE?
The SB140 uses M8x36mm hardware on the air can side and a custom Yeti reducer on the shaft side. If you swap between shocks, the reducer can be found here, https://yeticycles.com/gear/detail/shock-eyelet-spacer

CAN I PUT A COIL SHOCK ON MY SB140?
Yes, the SB140 is designed to be compatible with both air and coil-sprung shocks.

WHAT PERCENTAGE SAG DO YOU RECOMMEND FOR THE SB140?
We would advise starting with 30% sag, or 16.5mm of shock stroke for optimal pedaling efficiency and terrain compliance. Be sure to set your sag at your normal riding weight, gear included. Feel free to venture slightly above or below 30% to suit your personal preference.
Visit our shock set up page to help set up your suspension, https://shocksetup.yeticycles.com/calculator

WHAT SIZE SEAT POST DOES THE SB140 USE?
The SB140 uses a 31.6mm seat post.

WHAT SIZE SEAT COLLAR DOES THE SB140 USE?
The SB140 uses a 36.4mm seat collar.

WHAT IS THE WARRANTY ON MY SB140?
The SB140 has a LIFETIME manufacturer’s warranty.

WHAT IS THE LONGEST TRAVEL DROPPER POST I CAN RUN ON THE SB160?
This is mostly defined by your inseam. You can run any travel as long as you are above the minimum insert mark and you are not so low your tire rubs on your saddle or your dropper bottoms out in the frame. Your local Yeti dealer can help you sort this out. We run 150mm drop on SM frames, 175mm drop on MD frames and a 200mm drop on LG-XXL.

CAN I CONVERT THIS BIKE INTO A “MULLET” BIKE AND PUT A 27.5” WHEEL ON REAR OF THE SB140?
It is possible, but we would not suggest it as it would lower your BB too much and slacken your head tube angle and seat tube angle. But hey, if those changes suit your ride style then go for it.

LIFETIME WARRANTY

HERE’S EVERYTHING YOU NEED TO KNOW ABOUT OUR LIFETIME WARRANTY:
All 2019 (or newer) frames, including the Switch Infinity, are covered for life against damage due to manufacturing defects for the original purchaser. Paint and finish are covered for 1-year. We will repair or replace, at our discretion, any frame we deem defective. There are a few conditions: you must register it online at yeticycles.com and you must take it to an authorized Yeti Cycles dealer for processing. Warranty does not cover damage due to ordinary wear and tear, neglect or intentional destruction. From a slingshot or your truck.
If you happen to have a crash or non-warranty situation, we’ll get you back on the trail with a reasonable replacement price. Same conditions as above.
Lifetime Warranty applies to all 2019 and newer frames (including the SB100). Model year 2018 and older frames will be covered under our previous warranty (5-year or 2-year based on time of purchase).
Simple as that. No fine print.

DISCLAIMER
Yeti Cycles is not responsible for any damages to you or others arising from riding, transporting or other use of your bicycle. In the event that your frame breaks or malfunctions, Yeti Cycles shall have no liability or obligation beyond the repair or replacement of your frame pursuant to the terms outlined in the warranty.
*If you have a warranty concern, please contact your authorized Yeti Cycles dealer.

YETI CYCLES
621 Corporate Circle, Unit B Golden, CO 80401
(p) 303-278-6909
(f) 303-278-6906
yeticycles.com

BUSINESS HOURS
Monday-Friday 8AM-11:30AM (MST) 1:00PM-5:30PM (MST)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals