NSF XLB-204882 7-Tier Metal Panel Shelf Shelving Unit Installation Guide
- June 17, 2024
- NSF
Table of Contents
NSF XLB-204882 7-Tier Metal Panel Shelf Shelving Unit
Product Information
Specifications:
- Product Name: 7-Tier Wire Shelving Rack
- Model: 7T-2800LBS
- Maximum Weight Capacity per Shelf: 400lbs when equally distributed on feet levelers
- Maximum Entire Unit Weight Capacity: 700lbs when equally distributed on casters
Product Usage Instructions
Package Contents:
- 7 x Shelf (A)
- 56 + 2 extra Tapered Lock (B)
- 4 x Top Pole (C) with pole cap and pole connector preassembled
- 4 x Bottom Pole (D) with threaded insert preassembled
- 4 x Wheel (2 locking, 2 non-locking) for mobile option
- 4 x Feet Leveler (G) for stationary option
- 24 x Black plastic spacer (NOTE: Discard the black plastic spacers G, these are only for packing purpose)
- Nylon strap (H) x 2, Wall anchor (I) x 4, Screws (J) x 4
Assembly Instructions:
- Snap the two halves of a tapered lock (B) onto bottom pole (D) at the desired height. Repeat for all bottom poles.
- Screw top pole (C) onto bottom pole (D) and hand tighten.
- Insert bottom poles (D) through the corner holes of the shelf (A).
- Push the shelf firmly onto the tapered locks (B).
- Repeat steps for additional shelves.
Important: Installing wall straps is not necessary but highly recommended for safety.
FAQ
Q: What is the maximum weight capacity of each shelf?
A: The maximum weight capacity per shelf is 400lbs when equally
distributed on feet levelers.
Q: Can the shelving unit be used without installing wall straps?
A: Yes, the shelving unit can be used without installing wall straps, but
it is highly recommended to ensure stability and safety.
Q: How should heavier and lighter items be placed on the shelves?
A: Heavier items should be placed on lower shelves, while lighter items
should be placed on top shelves to maintain stability.
Warning:
Maximum weight capacity per shelf is 400lbs when equally distributed on feet
levelers.
Maximum entire unit weight capacity is 700lbs when equally distributed on
casters.
Failure to follow these instructions may result in serious injury or death of
yourself and people around you.
Some of the part are heavy and/or has shape edge, please install it carefully
to avoid hurt you and people around you.
Caution:
Do not stand on or climb on the shelving unit.
Place heavier items on lower shelves and lighter ones on top shelves.
PACKAGE CONTENTS
Attention: Please install it with 2 people
ASSEMBLY INSTRUCTIONS
-
With the tapered end facing up, snap the two halves of a tapered lock (B) at the desired height on bottom pole (D).
Repeat for the remaining bottom poles (D), making sure the tapered locks (B) are installed at the same grooved line on each bottom pole (D).
Attention: The wheel (E) must be fully screwed to the bottom pole (D) by wrench Attention:The tapered must be fixed to the groove on the pole, and make sure the tapered does not slip before installing the shelf -
Rest shelf (A) on its side, then insert the bottom poles (D) through the corner holes of the shelf (A).Note: Make sure the lip of shelf (A) is facing down and the levelers (F) on bottom poles (D) are on the floor.
-
Turn assembly upright and push the shelf (A) firmly onto the tapered locks (B). Note: Make sure the lip of shelf (A) is facing down and the levelers (F) on bottom poles (D) are on the floor.
-
Repeat steps 1-3 for the second shelf (A).
-
Screw top pole (C) onto bottom pole(D), hand tighten.
-
Repeat steps 1-4 for the remaining shelves (A).
Refer to image 6-1 for the assembled unit of stationary option. -
Repeat steps 1-4 for the remaining shelves (A).
IMPORTANT:
Installing wall straps is not necessary, but it is highly recommended.
Step 1. Loop the Nylon straps (H) around the top side of the top pole nearest to the wall.Use 1 per side.
Step 2. Pull the Nylon Straps (H) against the wall and mark holes where
you’d like to install your anchors (I) or screws (J) TIP!
Use a stud finder to determine if you are installing into drywall or wood
wall.
FOR DRYWALL
Drill a hole in the wall at the marked point roughly the depth of the anchor
(I). Screw the anchor (I) into hole until flush.
Screw screws (J) into anchor (I) until snug.
FOR WOOD STUDS
Drill a pilot hole into the wall at the marked point.
Screw screws (J) into holes until flush.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>