NSF Construction EF 238-44707-00E Commander Series Commercial Gas and Commercial Electric Water Heater Instruction Manual

June 17, 2024
NSF Construction EF

NSF Construction EF 238-44707-00E Commander Series Commercial Gas and

Commercial Electric Water Heater

NSF-Construction-EF-238-44707-00E-Commander-Series-Commercial-Gas-and-
Commercial-Electric-Water-Heater- product

Product Specifications

  • Product Name: NSF Construction EF, Commander Series Commercial
    Gas and Commercial Electric Water Heater

  • NSF Kit Part No.: 265-44542-04

  • Recommended Gallon Size: 6 thru 120 gallons

Product Usage Instructions

Installation Requirements
Before starting the installation, ensure that the water heater complies with local codes and ordinances. If there are no local codes, follow the National Electric Code or the National Fuel Gas Code.

Required Tools and Materials

  • RTV sealant (provided)
  • NSF label (provided)
  • Caulk gun

Installation Procedure

  1. Seal the water heater to the floor using RTV sealant, ensuring a complete seal without leaving voids.
  2. Place the NSF label on or adjacent to the rating plate.
  3. Remove pipe plugs and element plugs (if applicable) and replace them with NSF approved plugs provided.

FAQ

  • Q: What should I do if I am unsure about the installation process?
    A: It is recommended to consult a qualified technician for the installation of the NSF construction components to ensure safety and compliance.

  • Q: Can I use any RTV sealant for sealing the water heater to the floor?
    A: It is advised to use the provided RTV sealant to ensure proper sealing and adherence to safety standards.

  • Q: How do I know if I have the correct NSF kit for my water heater?
    A: Refer to the provided NSF Kit Part No. (265-44542-04) to ensure you have the correct kit for your water heater.

NSF CONSTRUCTION

EF, COMMANDER SERIES COMMERCIAL GAS AND COMMERCIAL ELECTRIC WATER HEATER INSTALLATION INSTRUCTIONS
THE MANUFACTURER OF THIS WATER HEATER WILL NOT BE LIABLE FOR ANY DAMAGE RESULTING FROM FAILURE TO COMPLY WITH THESE INSTRUCTIONS. READ THESE INSTRUCTIONS THOROUGHLY BEFORE STARTING.

For safety and convenience, the NSF construction components must be installed and serviced by a qualified technician.

Before proceeding with installation of this NSF kit, please assure that this water heater has been installed in accordance with local codes and/or ordinances. In the absence of local codes, this water heater must be installed in accordance with the National Electric Code — latest edition or, the National Fuel Gas Code, ANSI Z223.1-(Latest Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions). Refer to Installation instructions provided with this water heater.
Assure the correct NSF kit for this water heater has been provided.

NSF Kit Required

Gallon Size| NSF Kit Part No.
6 thru 120| 265-44542-04

Tools and Materials Required:

RTV sealant (provided)
NSF label (provided) attached to these instructions Caulk gun

Installation Procedure:

  1. Seal water heater to floor using RTV sealant. Be sure to seal water heater completely to floor without leaving voids (see Figure 1).
  2. Place NSF label on or adjacent to rating plate.
  3. Remove pipe plugs and element plugs (if applicable) and replace with NSF-approved plugs provided.

NSF-Construction-EF-238-44707-00E-Commander-Series-Commercial-Gas-and-
Commercial-Electric-Water-Heater- \(2\)

WARNING! CANCER AND REPRODUCTIVE HARM WWW.P65WARNINGS.CA.GOV

As required by the state of California Proposition 65.
238-44707-00E REV 5/18

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals