VEVOR 3L 0.8 Gallons Food Grade PC Tank 290W 110V User Manual

VEVOR 3L 0.8 Gallons Food Grade PC Tank 290W 110V

Introduction

Manufacturer

• The manufacturer’s details are shown on the identification plate

0perator

• Based on different applications. there are two types of persons.

User

• By Health standards people trained in complete techniques,
• Knowing all to distribute slush has below ability after reading this manual
• Place and change the slush machine
• Properly dispensing the products
• Cleaning the slush machine
• Specialized technical people
• Studied this manual and trained how to install, use and maintain this slush machine;
• When serious fault, can repair the slush machine and know this manus well;
• Master all information in the manual and explain the diagrams and graphs correctly;
• Know important hygienic knowledge well, prevent accident
• occurring, know technical and safety standards
• Have experience in serving this kind of slush machine.
• Master treatment measures for emergencies find separate safety
• device and use the machine correctly
• People are banned from using the machine who do not accord with the above requirement

Manual distribution

• Users have to read this manual carefully before using it.

Function and content

• Offer vital information on using and installing

Who to read the manual

• Users and specialized technical people.
• This manual is an inseparable part of the machine.
• So it needs to be delivered to the purchaser when sold.

How to keep a manual

• The manual has to be placed near the machine and kept Intact and clear

Machine description

Usage

• This machine is specially used for making slush.
• If used to make dairy and other foods, bowl material temperature needs to be tested and abide by the machine’s current regulations and standard

Main Component

1. Bowl roof
2. Bowl
3. Control panel
4. Water tray
5. Water tray cover
6. Drain hose
7. Tap
8. Handle
9. Machine foot

In this manual, the items are as below

• XRJ3LX1, one-bowl slush machine
• XRJ3LX2, two-bowl slush machine
• XRJ3LX3, three-bowl slush machine

Technical data

Remarks: Capacity and weight are the approximate numbers

• The manufacturer has the right to change and will not notice specially.
• Any change or increase has to be approved and executed by the manufacturer.

Control panel Fig.3

Safety Manual

• Slush machine parts and condenser installation, slush machine troubleshooting. exclusion and maintenance have to be operated by manufacturer professionals or people who have related experience.
• Without experienced people monitoring or guiding, the slush machine can not be used by disabled, sense-disabled, mentally disabled people, who lack experience and knowledge
• Children need to be taken care of when playing near the machine.
• When a machine’s wire is broken, they have to be replaced by manufacturer professionals or people who have related experience.
• When the machine is scraped, it has to be delivered and handled by a related authority institution

Transportation and storage

Packing

• Carton box, contoured foam & collect.

Packing size (approximate)

Remarks: Packaging size and weight are approximate.

Transportation

• Keep upward and carried by two people at least.

Storage

• Notice: please do not exceed three layers.

Installation

• The slush machine has to be installed indoors with hard and plain ground under enough light and ventilation (Ground inclination can’t be more than 2 degrees)

Parts list

• After cleaning and disinfecting all indicated manual parts have to be coated with lubricating oil.

Position to install

• Installation positions have to be planned;
• Installation places have to be hard and plain
• Installation condition is enough light and ventilation and clean;

The power socket is also needed;

• Installation distance from other objects see below fig. 6

Handling package material

• Handling packing material separately under local rules and we suggest keeping it to repack and ship in future.

Connect power

• Ensure the slush machine is off before connecting power.
• Then plug in to connect power.
• Data can be referred from the machine’s back nameplate.
• Warning: Socket has to be placed within user-touching distance to unplug quickly when emergency without using other tools.

Operation

Preparing material and stirring evenly

Warning: This machine can’t make Margarita and other alcoholic drinks.

Remove the lid as below steps

1. Lift the top lid;
2. Pour the material into bowls

Warning: Hot liquid can not be put in(hot liquid means the degree exceeds 25 *C) Material level can not exceed maximum height level

Close the top lid after pouring the material

• Warning: Before connecting the power or starting the machine, put the material into a bowl Material can not just be water.

• Warning: Banning putting a hand in the bowl when the machine is working

Starting a 1-BOWL SLUSH MACHINE

Starting a 2-BOWL SLUSH MACHINE

Starting a 3-BOWL SLUSH MACHINE

Dispensing slush

• Pull down the handle and slush will outflow from the bowl
  • Attention: if distributing slush first time or after a long stop, please extrude and waste a little and then distribute customers.
  • Attention: The material temperature in the bowl needs to be tested with a Standard thermometer timely to ensure the material temperature is lower than the storing temperature.
• Power can not be cut off when the machine is working or there are material.

Emergency

• Warning: When an emergency, the machine needs to be turned off by the power button and cut off the power
• If frozen, cut off power and ask for specialized people to handle it.
• If fire, clear the nearby area and ask for professionals.

Cleaning and maintenance

• Before cleaning or maintaining external parts, please ensure the main switch is off and unplug.
• Any cleaning or maintaining protection supplies need to be worn (gloves. glasses and so on) based on local safety standards.
• When cleaning or maintaining. operate as below.
• Wear protective gloves against an accident.
• Do not use solvents or flammable substances
• Do not use tough or metal sponges to clean the machine or parts
• Do not spray liquid in nearby areas.
• Do not wash parts in the bow!
• Do not dry parts in the furnace or microwave oven.
• Do not immerse the machine in water
• Do not spray the water to the machine directly.
• Warm water and approximate cleaner can be used (abiding by local law and rules)
• After finishing, make sure that all protective covers and guards that have been removed or opened and sent back in place and properly secured.
• Cleanliness and hygiene have to be taken carefully and forcibly based on a local standard to ensure qualified slush Cleanliness and hygiene have to be taken carefully and forcibly based on local standards to ensure qualified slush Bowl needs to be cleaned every day at least and abiding by local laws and regulations cleaning times may be added based on different products More information, please consult manufactories.
• If the machine will not be used for one day continuously please clean distributing taps with a clean Even though the machine’s components stainless steel, plastic and rubber are easy to clean as well as its shape, it is still necessary to prevent germs and fungi reproduction due to halfway cleaning
• When the plug is not pulled out or the total switch is in the open state. do not clean or maintain the machine.

Empty Bowl

• Before cleaning the bowl, empty the bowl
• If it is the first time use, no need to make it empty.
• This manual just explains one bowl as a sample Other boil operations are the same based on related buttons.
• Please set the bowl to “clean slate”, then pour material from the bowl.

Disassembling the dispensing tap
Before removing the bowl, it is recommended to disassemble the tap, after cleaning, the tap must not be reapplied until the bowl has been correctly positioned in its seat. Remove the fastener with a screwdriver, then disconnect the dispensing handle by pushing upward, then push the piston and spring downward, and remove the O-ring. Put all spare parts in lukewarm water water temperature around 50°C) and clean as fig. 9

• Do not disassemble taps when there are products or liquid in bowls

Move out the bowl and cover

• Move out every bowl to clean the machine.

Move out the bowl as below steps:

1. Lift the top cover upward and take it out. Pull the tank upward and outward to completely remove it from its seat.
2. Screwing off the nut.
3. Take out the stirrer and the seal of the stirrer.

Clean and disinfect parts

• All dismantled parts should be cleaned thoroughly

Importance:

• Cleaning way has to abide by local current hygiene standards.
• Please operate as per the below instructions:
• Pour water into the container. mix sanitiser with water (Add 2% sodium hypochlorite to water)
• Sponge with sanitizer clean bowl, cover and evaporator thoroughly clean with water thoroughly
• Add sanitiser to another container.
• Put dismantled parts in sanitiser for 30 minutes.
• Re-clean with water thoroughly.
• Make the parts dry.
• Assemble machine under 7.5instruction.
• Sponge with sanitiser to clean the roof and the parts touching the raw material.

Retain 30 minutes

• Clean the bottom surface with water 2-3 times by the sponge.
• Put the cover in a clean area and dry it with a rag Ban cleaning with water or disinfecting before taking away the cover.

Reset cleaned parts

• All disinfected parts have to be reassembled carefully.
• Some parts need to be lubricated to work normally.
• Put gasket(A) on the stirrer see Fig. 12
• Importance: Check gasket in regular if broken. Please replace the new one.
• Replace gasket(A) once at least one year Using the Vaseline provided, lubricate the seal A) see Fig 13
• Install seal (B), and lubricate the entire surface with Vaseline as arrow marks, see Fig. 14

See Fig 14-1

• Replace the seal ring. When the motor part leaks, you need to replace the seal ring Take out the motor bracket connected to the motor and then replace the head seal ring (washer of axis, seal of axis).
• When replacing. You need to add some Vaseline Then install the motor bracket connected to the motor.

Install taps as below instructions as Fig. 17

1. Lubricate the bolt totally with Vaseline.
2. Insert screw when taps are steady.

Attention: Install all parts under the figure’s instructions. If not lubricated with Vaseline well, the material may permeate

Clean step
Before using this machine, below cleaning steps below are needed

1. Fill a bowl with water fully
2. Start the machine only in cleaning mode and stir for 5 minute
3. Stop the machine and open the tap to clear the container.

Cleaning drip tray

• The drip tray should be emptied and cleaned every day
• Attention: All machine drip trays should be cleaned drip tray need to be emptied and cleaned.
• Take out the drip tray by lifting it from the top.
• Wash the tray and grid separately with lukewarm water. Dry all Of the components.
• Fit the tray back in place and press down to secure it to the machine. Reposition the grid on top of the tray
• When machines stop clean by wet rag and dry the parts.

Replace bulb

• Only when the machine power is off and unpluggedbulb can be replaced
• According to the below figure, open the small back panel, replace the LED bulb, and after assembling put the panel back, and confirm closed well.

Clean condenser

• Only professionals can clean condensers They know all operating steps well using the approximate device and abide by local law and regulations strictly
• The condenser needs to be cleaned regularly.
• Warning: Machine sharp surface may be revealed after dismantling safety protection parts. A dirty condenser will weaken the machine’s function.
• The condenser can be seen after taking out safety protection parts.
• Even though only one plate (front or back or side) is not installed the machine is also banned from use. Operators are banned from cleaning condenser
• Protection parts need to be positioned by Screwdrivers.

Cleaning condenser of one-bowl slush machine
Safety protection parts need screwdrivers to fasten and dismantle.

1. Loose side panel screw.
2. Take outside panel
3. Dismantle safety protection parts. Brush the dust from the condenser surface with a dry brush as Fig21

Cleaning condenser of two-bowl slush machine According to the following instructions

1. Loose 3 crews of the back plate.
2. Loose 5 screws o the side plate.
3. Take out the side panel.
   • Dismantle safety protection parts
   • Brush the dust from the condenser surface with a dry brush as below.

Scheduled maintenance

• This machine needs to be maintained by professionals regularly (at least 1 year).
• Regular maintenance can ensure the machine and its parts are in a good safety state
• Any broken parts need to be replaced with the original manufacturer
• When any parts of the machine are malfunction or broken machine is banned from use.
• The user can not maintain the machine himself

Waste treatment

• Electronic waste needs to be handled according to2002/96/EC
• But wastes need to be dismantled and classified and useful parts should be recycled.
• The above rubbish bin reminds people to classify rubbish.
• Treating waste correctly will protect our environment.

Troubleshooting

Fault Codes And Solutions For Slush Machine

Intelligent electronic valve system

Slush machine explosive diagram

Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to theproduct you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product. The manufacturer reserves the right to make changes to the granita machine without notice.
Warning: This machine can’t make Margarita and other alcoholic drinks.
E-mail Customer: Service@Vevor.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>