ADD AC2302701NA Ford Bronco Tailgate Molle Panel Instruction Manual

ADD AC2302701NA Ford Bronco Tailgate Molle Panel

Product Information

(Wrench) 7/16, 10mm
Ratchet
Time Required| 1 Hour
Skill Level| Easy/Intermediate
Included in Kit| 4- 1/4-20 Large Flange 0.165 rivet nut
4- 1/4-20 X 3/4 Button Head Bolts
2- 1/4-20 X 1/2 Button Head Bolts
10- 1/4 Flat Washer
2- 1/4-20 Nylon Lock Nuts
2- 1/4-20 X 7/8 Threaded Hex Standoff
2- 1/4-20 X 1 1/2 Threaded Hex Standoff

Product Usage Instructions

1. Read and understand all instructions, warnings, cautions, and notes contained in the installation instruction guide.
2. Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of the vehicle if required for installation of this product.
3. If you do not feel capable of performing this installation, it is recommended to take the product to a trained professional.
4. Contact customer service with any questions or concerns before installing the product. Customer Service: 480-671-0820
5. Ensure that all contents of the package are not damaged and that all installation hardware has been included.
6. If parts are missing from the kit, provide the following information:
   • Name of purchase location
   • Bar Code on side of box
   • Date above bar code
   • Date inside box cover
7. Always wear eye protection when operating power tools.
8. Remove plastic as shown.
9. Locate the two factory holes as shown and use a uni bit to drill a 7/16 hole.
10. Install the provided 1/4-20 Rivet Nut with a rivet nut tool in the bottom slots. If they do not fit, use a uni bit to open the slot. Alternatively, use a 1/4-20 x 3/4 hex head bolt, a 1/4 washer, and a 3/8 nut to install the rivet nuts. Tighten using a 9/16 wrench and a 7/16 socket on an impact. Hardware is not included.
11. Install the provided 1/4-20 Rivet Nut with a rivet nut tool in the top holes you drilled in step 2. If you do not have a rivet nut tool, use a 1/4-20 x 3/4 hex head bolt, a 1/4 washer, and a 3/8 nut to install the rivet nuts. Tighten using a 9/16 wrench and a 7/16 socket on an impact. Hardware is not included.

TOOLS REQUIRED

(Allen Wrench) 5/32 (Wrench) 7/16, 10mm Ratchet

TIME REQUIRED: 1 hour

SKILL LEVEL: -Easy/Intermediate

INCLUDED IN KIT

• 4- 1/4”-20 Large Flange 0.165” rivet nut
• 4- 1/4-20 X 3/4” Button Head Bolts
• 2- 1/4-20 X 1/2” Button Head Bolts
• 10- 1/4” Flat Washer
• 2- 1/4-20” Nylon Lock Nuts
• 2- 1/4-20 X 7/8” Threaded Hex Standoff
• 2- 1/4-20 X 1 1/2” Threaded Hex Standoff

WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

BEFORE YOU INSTALL THIS KIT

• Read and understand all instructions, warnings, cautions, & notes contained in this installation instruction guide. Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of vehicle if required for installation of this product.
• This install may require some technical skills and knowledge of basic mechanical work. If you do not feel that you are capable of performing this install please take this product to a trained professional.
• After reading this guide please contact us with any questions or concerns before installing product.
• Customer Service 480-671-0820
• Addictive desert designs is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install.
• Proper installation of this kit required knowledge of the factory recommended procedures for removal and installation of original equipment components.
• We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information:
  • Name of purchase location
  • Bar Code on side of box
  • Date above bar code
  • Date inside box cover

ALWAYS WEAR EYE PROTECTION WHEN OPERATING POWER TOOLS.

REAR DOOR MSP
21+/FORD BRONCO

1. STEP 1
   Remove plastic as shown.

2. STEP 2
   Locate the two factory holes as shown below and use a (uni bit) to drill a 7/16” hole.

3. STEP 3
   Install the provided 1/4”-20 Rivet Nut with a (rivet nut Tool) in the bottom slots. (If they do not fit use a (uni bit) to open the slot)
   TECH TIP: If you do not have a rivet nut tool, use a 1/4-20 x 3/4 hex head bolt, a 1/4 washer, and a 3/8 nut to install the rivet nuts. Tighten using a (9/16 wrench) and a (7/16 socket) on a impact.
   HARDWARE NOT INCLUDED

4. STEP 4
   Install the provided 1/4”-20 Rivet Nut with a (rivet nut Tool) in the top holes you drilled in step 2. TECH TIP: If you do not have a rivet nut tool, use a 1/4-20 x 3/4 hex head bolt, a 1/4 washer, and a 3/8 nut to install the rivet nuts. Tighten using a (9/16 wrench) and a (7/16 socket) on a impact.
   HARDWARE NOT INCLUDED

5. STEP 5
   Install the 1/4”-20 x 7/8” threaded hex standoff using a (1/2 wrench). (DO NOT overtightened due to breakage)

6. STEP 6
   Install the 1/4”-20 x 1 1/2” threaded hex standoff using a (1/2 wrench). (DO NOT overtightened due to breakage)

7. S TEP 7
   Using a (uni bit), drill the accessory ready holes located on the plastic to a 11/16” hole.

8. STEP 8
   Re-install the plastic with the threaded standoffs extruding out.

9. STEP 9
   Install the aluminum backer plate with the provided 1/4”-20 x 1/2 button head bolts, nylon lock nuts, and washers with a (7/16 Wrench) and a (5/32 allen ).

10. STEP 10
    Install the rear door msp with the provided 1/4”-20 x 3/4” button head bolts, and washers using a (5/32 allen).

11. STEP 11
    Stand back and enjoy your new ADD Rear Door MSP.
    Check and re-tighten, if needed, all mounting bolts after 100 miles and periodically thereafter.

This product is protected by one or more U.S. patents
www.addictivedesertdesigns.com/patents

For Additional Support or Technical Questions,
Please Call :480-671-0820 or
Email: Info@AddictiveDesertDesigns.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>