PROGRESS LIGHTING P350261-31M Latham 3 Light 18 Inch Semi Flush Mount Ceiling Light Instruction Manual

PROGRESS LIGHTING P350261-31M Latham 3 Light 18 Inch Semi Flush Mount Ceiling Light Instruction Manual

PACKAGE CONTENT

HARDWARE CONTENTS (not actual size)

• Screw (#8-32) Qty:2

• Wire Nut Qty:3

• Round Mounting Plate Qty:1

• Hex Nut (#8-32) Qty:2

• Cylinder nut (#8-32) Qty:2

• 12″ Stem (1/8IP) Qty:4

• Nipple (1/8IP) Qty:3

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or Install the product.

CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.

CAUTION: Risk of fire, Min, 90°C supply conductors, Consult a qualified electrician to ensure correct branch circult conductor.

WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

CAUTION: All glass is fragile. Use care when handling glass shades and bulbs. Preparation

Preparation

1. Before beginning installation, make sure all parts are included using the contents diagrams from page If any part is missing or damaged, do not attempt to assemble, install or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not Included): Philips screwdriver, pillers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or deaners that contain alcohol.

Assembly Instructions

1. Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. You now need to adjust the screw length according to the fixture canopy depth.
   

2. Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
   Lift up the fixture and pass the screws (AA) through the two mounting hole in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 5 and 10.
   
   Next, take the fixture down and go back and tighten the hex nuts (DD) up against the round mounting plate (CC). You now should have the correct length of threads for mounting the fixture.
   Thread both screws up & down for adjustment
   

3. Pass the wires through the round tube (C) and canopy (B). Attach the tube (C) onto the fixture (A), secure it tightly.
   

4. Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire. Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
   

5. Pass the screws (AA) through the two holes in the canopy (B). Secure the fixture to the screws (AA) using the two cylinder nuts (EE) provided. Tighten securely in place.
   

6. Thread lamp (not included) into the fixture socket. Use a 60-watt MAX incandescent candelabra base lamp, SBCFL or SBLED.
   

7. Remove existing canopy parts from canopy (B), Install canopy parts and 90° swivel (D) into canopy (B), secure tightly.

8. NOTE: During this step, determine the hanging length of your fixture by adding/removing stems (FF/GG) and cutting the electrical wire and ground wire to length.
   Do NOT cut electrical wires or ground wires until this overall length is determined. Leave at LEAST 6 inches MINIMUM of wire past the canopy to allow for easy connections in step 9.
   Once hanging length is determined, it is easier pulling the wires through the unassembled stems (GG) and nipples (HH). Once the wires are pulled through, you can then assemble the stems and nipples tightly together.
   Next, attach one end of the stems onto the fixture (A) and secure it tightly. Pass wires through the canopy (B) and secure it tightly to the stems (FF).
   

9. Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
   Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.

10. Pass the screws (AA) through the two holes in the canopy (B). Secure the fixture to the screws (AA) using the two cylinder nuts (EE) provided. Tighten securely in place.
    

11. Thread lamp (not included) into the fixture socket. Use a 60-watt MAX incandescent candelabra base lamp, SBCFL or SBLED.
    

WARRANTY AND EXCLUSIVE REMEDY Progress products, when properly installed and under normal conditions of use, are warranted to our customen only to be free from defects in maternal and workmanship at time of shipment. All warranty daims must be asserted within one year from date of purchase of the sulject items, thereaften, warranty claims will not be hanored, Customers’ sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or wristmanship at time of shipment Progress’s sole and masimum liability for a defective product shall never exceed the cost of the subject product EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGUGENCE, STRICT UABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBIECT PRODUCT OR PRODUCTS.

Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at nur option (excluding stallation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Dur customers are not authenged to extend warranties or remedies on our behalf to anyone. Such unauthorized extension of warranties or remedies by the customer shall nemain custooter’s responsibility, Customer is responsible for determining the suitability of our products for customer’s use or resale, e for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>