TETOTE 35721745 LED Bathroom Vanity Wall Mirror Installation Guide

: June 15, 2024
: TETOTE

Table of Contents

TETOTE 35721745 LED Bathroom Vanity Wall Mirror
Specifications
Parameter
Package Contents
CONTACT US
Packing list
USE INSTRUCTION
BEFORE INSTALLATION
INSTALLATION
Product Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TETOTE 35721745 LED Bathroom Vanity Wall Mirror

Specifications

Dimension: 24 x 36, 28 x 36, 30 x 36, 36 x 36, 40 x 24, 40 x 30, 48 x 30, 48 x 36, 55 x 36, 60 x 36, 71 x 36
Size: 61 x 91 x 4 cm, 71 x 91 x 4 cm, 76 x 91 x 4 cm, 91 x 91 x 4 cm, 101 x 61 x 4 cm, 101 x 76 x 4 cm, 121 x 76 x 4 cm, 121 x 91 x 4 cm, 139 x 91 x 4 cm, 152 x 91 x 4 cm, 180 x 90 x 4 cm
Watts : 60W, 60W, 60W, 90W, 60W, 90W, 90W, 90W, 90W, 90W, 108W
Lumens: 5375LM, 5750LM, 5950LM, 6500LM, 5750LM, 6375LM, 7125LM, 7750LM, 8500LM, 8613LM, 10125LM

Parameter

Color Temperature
Input Volta ge: AC100-120V
Output Voltage : Yes
CRI
Working Temperature
Life Span
Anti-fog
Nema Rate: 3
Wiring Method: Hardwired / Plug In
Switch: Touch Sensor Switch

Package Contents

Mirror x 1
Bracket x 1
Screws x 4+2
Anchors x 4+2

CONTACT US

Note: After opening the package, Please inspect the product immediately for damage in transit or missing parts. If there is any missing, Please contact us by (sales@tetote-tech.com) or you can contact us at Amazon by following these steps:

Open “Orders” at Amazon
Find the product you have purchased and open the product page
Click Sold by “tote” -Click”Ask a question”
Click “An order I have placed”
Click “Your product” -Click “Other” -Click “Troubleshooting”
Then you can send us messages, we will reply within 24 hours.

Packing list

USE INSTRUCTION

PIease use in safe voltage range. (IOOV-120V)
Use electrical tape to wrap around the wires to prevent leakage.
Do not strike mirror glass with hard or pointed items.

DANGER: Before installation, make sure the main power is cut off.
WARNING: Installation must be performed by a qualified licensed electrician.

BEFORE INSTALLATION

Note: Thank you very much for using tote products, in order to facilitate the use of tote products, please read this instruction carefully before you begin installation.

Important Safety Instructions:
- Please read all instructions carefully before assembling the item.
- Assembly by two or more adults is highly recommended.
- To connect the wires to the electrical junction box, a qualified technician or electrician is highly recommended.
- Disconnect power before installing, adding, or changing any components.
- Ensure that the fixing location can take the weight of the complete fitting. (solid stone/brick walls)
- To prevent injury, the mirror must be installed according to these instructions.
Pre-assembly:
- After opening the package, inspect the product immediately upon receipt for transit damage or missing parts.
- Keep the voltages between IOOV and 120V. If the voltage exceeds 120V, please use a transformer.
- You can connect the wires directly to your junction box or the plug.
Before installation, please check to make sure the mirror is working properly :
- The left button is the anti-fog touch .
  Anti-fog film will automatically turn off one hour after opening. When you are not using it, remember to turn off the switch to prevent wasting energy.
- The middle button is the color temperature touch .
  The first touch is white light, the second touch is yellow light, the third touch is natural light, and so on. Press and hold it to infinitely adjust the color temperature.
- The right button is the light touch .
  The first touch is to turn on all the lights, the second touch is to turn on only the front lights, the third touch is to turn on only the back lights, and the touch again turns off all the lights, and so on. Press and hold it to infinitely adjust the brightness.

INSTALLATION

Installation tools

Before installation, please lift the mirror against the wall, keep an appropriate safety distance from the faucet, confirm the installation position and installation height of the bracket, use a spirit level to level the bracket, and mark the hole position on the wall.
The mirror can be hung horizontally or vertically. You can choose the hanging method according to your preference. Here is the vertical hanging installation method, the horizontal hanging is the same.
Use an electric drill to punch holes at the marked spots, and then apply wall anchors with hammer. (1/4″ (6mm) drill bit, drilling depth in 13/4″ (45mm) )
Mount the bracket to the wall with screws.
Connect the power. You can use the plug directly or connect the wire to a standard switch lighting circuit.
‘Use plug
After hanging the mirror, insert the plug directly into the standard socket

Olnstallation hardwired
Cut the plug and connect the mirror’s wire to the power by the wire connectors.

DANGER: Before installation, make sure the main power is cut off.

Place the mirror against the wall, align the hook with the bracket slot, slowly lower it so that the hook fits into the slot, and gently shake the mirror to ensure that the mirror is securely installed.