PROGRESS LIGHTING P500435-078 One Light Vintage Brass Contemporary Pendant Installation Guide
- June 17, 2024
- PROGRESS LIGHTING
Table of Contents
P500435 1-LT SMALL PENDANT
P500436 1-LT MEDIUM PENDANT
P500435-078 One Light Vintage Brass Contemporary Pendant
PACKAGE CONTENTS
PART | DESCRIPTION | QUANTITY |
---|---|---|
P500435 | P500436 | |
A | Fixture | 1 |
B | Canopy | 1 |
HARDWARE CONTENTS (not actual size)
Missing parts? Please contact Customer Service at
1-800-447-0573,
8am-8pm (Eastern), Monday – Friday, or at
customerservice@progresslighting.com
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs, To clean, wipe with damp cloth, Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. You now need to adjust the screw length according to the fixture canopy depth.
-
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift up the fixture and pass the screws (AA) through the two mounting hole in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 5.
Next, take the fixture down and go back and tighten the hex nuts (DD) up against the round mounting plate (CC). You now should have the correct length of threads for mounting the fixture. -
NOTE: During this step, determine the hanging length of your fixture by adding/removing stems (FF/GG) and cutting the electrical wire and ground wire to length.
Do NOT cut electrical wires or ground wires until this overall length is determined. Leave at LEAST 6 inches MINIMUM of wire past the canopy to allow for easy connections in step 4. Once hanging length is determined, it is easier pulling the wires through the unassembled stems (GG) and nipples (HH). Once the wires are pulled through, you can then assemble the stems and nipples tightly together.
Next, attach one end of the stems onto the fixture (A) and secure it tightly. Pass wires through the canopy (B) and secure it tightly to the stems (FF). -
Strip 3/8” of insulation from the electrical wire ends. Using wire nuts (BB), connect the smooth fixture wire to the white supply wire from the outlet box; connect the ribbed fixture wire to the black supply wire from the outlet box.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
-
Pass the screws (AA) through the two holes in the canopy (B). Secure the fixture to the screws (AA) using the two cylinder nuts (EE) provided. Tighten securely in place.
-
Thread the lamps (not included) into the fixture sockets. Use 100-watt MAX incandescent medium base lamp, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY:
Progress products, when properly installed and under normal conditions of use,
are warranted to our customers only to be free from defects in material and
workmanship at time of shipment. All warranty claims must be asserted within
one year from date of purchase of the subject items; thereafter, warranty
claims will not be honored. Customers’ sole remedy for a warranty claim or
otherwise shall be limited to repair or replacement of the subject product if
it is shown to have been defective in material or workmanship at time of
shipment. Progress’s sole and maximum liability for a defective product shall
never exceed the cost of the subject product.
EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS
WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR
IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO
CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR
ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE
CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE
SUBJECT PRODUCT OR PRODUCTS.
Therefore, the customer’s sole and exclusive remedy against us for breach of
the warranty, breach of contract or negligence or strict liability or
otherwise shall be limited to repair or replacement of the subject product at
our option (excluding installation and removal charges which shall not be our
liability) or, if we choose, refund of the purchase price. In no case does our
warranty and exclusive remedy extend to anybody other than our customers. Our
customers are not authorized to extend warranties or remedies on our behalf to
anyone. Such unauthorized extensions of warranties or remedies by the customer
shall remain customer’s responsibility. Customer is responsible for
determining the suitability of our products for customer’s use or resale, or
for incorporating them into objects or for applications which customer
designs, assembles, constructs or manufactures.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>