ALHAFIDH 32LG3 32 Inch LED TV User Manual

ALHAFIDH 32LG3 32 Inch LED TV User Manual

IMPORTANT SAFETY INSTRUCTIONS

This lightning flash with arrowhead symbol within an eqilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

‘WARNING

1. To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.
2. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance
3. Do not install this equipment in a confined or building-in space such as a book case or similar unit, and remain a well ventiation conditions at open site. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper table-cloths, curtains etc
4. Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus.
5.  The mains plug/appliance couple is used as disconnect device, the disconnect device shall remain readily operable.
6. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus
7. The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the lie,
8. Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:
   • Using cabinets or stands recommended by manufacturer of the television set. – Only using furniture that can safely support the television set
   • Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and television set to a suitable support.
   • Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture.
   • Educating children about the dangers of climbing on furniture to reach the television set or its controls. If your existing television set is being retained and located, the same considerations are above should be applied.
9. No naked flame sources, such s lighted candles, should be placed on the apparatus.
10. Keep a minimum distance of 5 cm around all edges of the display for sufficient ventilation,

Introduction

Precautions

Read all of the instructions before operating the set. Keep these instructions well for future use.

Product

• Do not block or cover the ventilation openings on the back cover.

• Do not push objects of any kind into this unit through the cabinet slots as they could touch
  the current carrying parts or short-circuit parts, resulting in fire, electric shock, or damage to the
  unit. + Do not attempt to open the cabinet as this may cause damage. There are no parts inside you can service by yourself Refer all servicing to qualified personnel

• Do ot touch the screen surface with fingers as this may scratch or mar the TV screen

• Do not impact the TV screen with hard pressure as this may damage the TV screen severely.

Power and Plug

• Unplug the set under the following conditions:
  • If the set will not be used for a long period of time.
  • If the power cord or the power outlet/plug is damaged
  • Follow the instructions to install and adjust the product. Adjust those controls that are covered in this operating instructions as improper adjustment of other controls may result in damage. If this happens, unplug the set and refer to the service personnel.
  • If the set is subject to impact or has been dropped to have the cabinet damaged

Power Cord and Signal Cable

• Do not allow anything to rest on or roll over the power cord and the signal cable,
• Protect the power cord and the signal cable from being trampled.
• Do ot overload the power cord or the power outlet.
• Do not expose the power cord and the signal cable to moisture.

Use Environment

• Do not place the set on an unstable cart, stand, or table.

• Place the set on a place that allows good
  wventilation.

• Do not use the set near damp, and cold areas.
  Protect the set from overheating.

• Keep the set away from direct sunlight

• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

• Do not use the set near dust place.

Cleaning

• Dust the set by wiping the screen and the cabinet with a soft, clean cloth or some special liquid cleaner.
• Do ot apply excessive force to the screen when cleaning,
• Do not use water or other chemical cleaner to clean the screen as this may damage the surface of the TV screen.

Hanging the TV Set on the Wall Warning: This operation requires two people.

To ensure a safe installation, observe the following safety notes:

• Check that the wall can support the weight of the TV set and wall mount assembly.
• Follow the mounting instructions provided with the wall mount.
• The TV set: must be installed on a vertical wall
• Make sure to use only screws suitable for the material of the wall.
• Make sure that the TV set cables are placed so that there is not danger of tripping over them.

All other safety instructions about our TV sets are also applicable here

Note: Illustrations within this publication are provided for reference only.

General Operation

Switching   on

Follow the instructions on this page on how to switch on your TV set and the remote control before going on to following pages describing how to use the channel set-up procedure.

1. Insert two batteries in the remote control. Precautions on using batteries:

   • Only use the battery types specified
   • Make sure you use the correct polarity.
   • Do not mix new and used batteries.
   • Do not use rechargeable batteries
   • Do not expose batteries to excessive heat such as sunshine, fire or the like, throw them in a fire, recharge them or try to open them, as this could cause them to leak or explode
   • Remove the batteries from the remote controlif you are not using it for a long period of time,

2. Connect the power cable FIRST to the television, THEN to a mains socket. (Note: I the power cable is connected to the television, please only connect the power cable to the mains
   socket.)

   • Ifyour TV is connected to an AC supply Your TV set should only be connected to an AC supply.It must not be connected to a DC supply.If the plug is detached from the cable, do not, under any circumstances, connect it to a mains socket, as there is a risk of electric shock.
   • If your TV is connected to a DC supply Your TV set should only be connected to DC supply. It must not be connected to a AC supply. If the plug is detached from the cable, do not, under any circumstances, connect it to a mains socket, as there is a risk of electric shock.

3. Connect an outside aerial to the ANTENNAIN socket at the back of the TV set. 4. When powered on, the TV will be turned on directly or be in standby. Note: For some models, switch the TV on by pressing the power button If the power indicator lights up, the TV set is in standby mode. Press the button on the remote control or on the TV set to turn on the TV,

Switching off

• To put the TV set into standby mode, press the ® button on the remote control or on the TV, the TV set remains powered up, but with low energy consumption
• To switch off the TV set, unplug the mains socket from the mains outlet.
  Note: For some models, press the power button to switch off the TV set

Network Connection

To access the internet, you must subscribe high speed broadband internet service from your internet service provider Your TV can be connected to your home network in two ways:

• Wired, using the RJ45 (LAN) connector on the back panel.
• Wireless, using the internal wireless or external wireless USB adapter and your home wireless network

Note: This function is not available for certain models. Instructions below are just the usual ways to connect your TV to the wired or wireless network. The connection method may be different depending on your actual network configuration. If you have any questions about your home network, please refer to your ISP (internet Service Provider).

Connecting to a wired network

To connect to a wired network:

1. Ensure you have:
   • An ethernet cable long enough to reach your TV
   • A router or modem with an available Ethernet port
   • Ahigh-speed internet connection
   • An Ethernet (LAN) port on the back of the TV
2. Connect your ethernet cable to the router and to the Ethernet port on the back of the TV,
3. Use the Network Settings to configure the TV.

Connecting to a wireless ne

To connect to a wireless network ossm

1. Ensure you have:
   • Arouter broadcasting a high-speed wireless signal
   • A high-speed internet connection
   • Awireless USB Adapter (not need for a built-in wireless connection).
2. The TV set with Wi-Fi Module.
3. Use the Network menu to configure the TV. Note: Some models may have internal wireless module, then the wireless USB adapter is unnecessary.
   Some external wireless adapters cannot be compatible with the TV.

Other Information

Troubleshooting

Most problems you encounter with your TV can be corrected by consulting the following troubleshooting list.

No picture, no sound

1. Check if the fuse or circuit breaker s working
2. Plug another electrical device into the outlet to make sure ittis working or turned on.
3. Power plug is in a bad contact with the outlet.
4. Check the signal source:

No color

1. Change the color system.
2. Adjust the saturation
3. Try another channel. Black-white program may be receive

Remote control does not work

1. Change the batteries.
2. Batteries are not installed correctly.
3. Main power is not connected,

No picture, normal sound

1. Adjust the brightness and contrast
2. Broadcasting failure may happen.

Normal picture, no sound

1. Press the Vol button to increase volume.
2. Volume is set to mute, press the mute button to restore sound.
3. Change the sound system
4. Broadcasting failure may happen

Unorderly ripples on the picture
It is usually caused by local interference, such as cars, daylight lamps and hair driers. Adjust the antenna to minimize the interference.

Blank screen in VGA mode
Perhaps the TV can not recognize the resolution set by the PC. Suggest to change to the best resolution or other standard resolutions of the Windows system.

Snowy dots and interference
If the antenna is located in the fringe area of a television signal where the signal is weak, the picture may be marred by dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the reception.

1. Adjust the position and orientation of the indoor/outdoor antenna.
2. Check the connection of antenna
3. Fine tune the channel
4. Try another channel. Broadcasting failure may happen.

Ignition

Black spots or horizontal streaks appear, or the picture flutters or drifts. This is usually caused by interference from car ignition system, neon lamps, electric drils, or other electrical appliance.

Ghost

Ghosts are caused by the television signal following two paths. One is the direct path, the other is reflected from tall buildings, hll, or other objects: Changing the direction or position of the antenna may improve the reception.

Radio frequency interference

This interference produces moving ripples o diagonal streaks, and in some case, loss of contrast in the picture. Find out and remove the radio interference source.

If the TV is crashed

1. Press the Power button to tum off TV, then press the Power button again to reset TV,
2. Unplug the power cord, then press the Power button to reset TV
   Note: If these 2 methods can not be resolved, please contact the after- sales to solve.

Base Installation

To fix the double support base on the unit by screws, the installation is completed.

Note: lllustrations below are provided for reference only and may differ from actual product appearance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>