DURENT A03507 Dining Living Room Chandelier Instruction Manual

DURENT A03507 Dining Living Room Chandelier

Product Information

Product Specifications:

• Parts Included: Single bar, Green ground screw, Canopy, Collar ring, Collar loop, Quick link, Chain, Loop, Fixture loop assembly, Tube, Arm
• Accessories Included: Wire connector, Mounting screw

Product Usage Instructions

Assembly & Installation:

1. Carefully unpack and check all parts and accessories.
2. Adjust the arms to the proper position and connect the fixture loop assembly to the arm with the tube.
3. Determine hanging height and connect chain links accordingly.
4. Lace wires through the chain and stop before reaching the top.
5. Turn off power at the main fuse or circuit breaker before installation.
6. Attach single bar to outlet box, raise canopy, secure canopy in place, and install the bulb.

Frequently Asked Questions (FAQ):

• Q: Can I install the product without a licensed electrician?
  A: It is recommended to have the product installed by a licensed electrician to reduce risks.

• Q: What should I do if some parts are missing?
  A: Contact customer support for assistance in obtaining any missing parts.

• Q: How do I determine the correct hanging height?
  A: Measure and adjust the chain links to achieve the desired hanging height.

Safety Instruction

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before the fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, with a max of 40W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing the bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (C) Single bar (1)

• (D) Green ground screw (1)

• (E) Canopy (1)

• (F) Collar ring (1)

• (G) Collar loop (1)

• (H) Quick link (8)

• (I) Chain (1)

• (J) Loop (1)

• (K) Fixture loop assembly (1)

• (L) Tube (3)

• (M) Arm (6)
  ACCESSORIES & QTY ENCLOSED:

• (A) Wire connector (3)

• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the? above illustration.

2. Make pre-installation

   • Step A1: Adjust the arms M to the proper position.
   • Step A2: Connect the fixture loop assembly (K) to the arm (M) with tube (L).
   • Step B1: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
   • Step B2: Attach the quick link (H) to connect the chain (I) and the loop(J) on the the top of upper fixture loop assembly (K).
   • Step B3: Carefully lace the wires through the chain (I)(every other link)and stop just before you reach the top of the chain (I). Gently pull the wires till snug.

3. Turn off power
   Before you start to make an installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).
     Place the wall switch in the“OFF” position.

4. Make installation

   • Step C1: .Attach the single bar (E) to outlet box with mounting screws (B). The side of the single bar marked “GND” must face out

   • Step C2: Raise the canopy (G) through the screw collar loop (I) and screw the collar loop (I) to a proper position by measuring.
     Unscrew the threaded ring (H) from the screw collar loop (I) and remove the canopy (G). In this way, you would know the
     Proper position on which collar loop it should be located.
     Note: The canopy (G) should be snug against the ceiling and the collar loop (I) should be screwed enough threads (no less than 6 threads )over the threaded nipple (C) for more secure hanging. If not, adjust the collar loop (H)on the single bar assembly by screwing the collar loop (I) in or out of the single bar (E) until the length is achieved.

   • Step C3: Slip the threaded ring(H) over the chain(K),then do the same with the canopy(G)

   • Step C4: Open the quick link(J), and attach the quick link (J) to connect the loop (I). Close the quick link(J).
     Pass the wires through the screw collar loop(H) to the top of the nipple(E) and gently pull till snug.

   • Step C5: If needed, cut off the wire length of the fixture. At this point, the remaining wire length measured from the top of the single bar(B) is at least 6″.

   • Step C6: Make wire connections
     Connect wires as below wires connecting shown below. TAKE NOTE OF THE COLOR OF THE FIXTURE, NEVER CONNECT WIRES TO GROUND WIRES
     Twist the plastic wire connector until wires are tightly joined together, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

   • Step C7: Raise canopy (E) to ceiling and secure canopy (E) in place by tightening threaded ring (F) onto collar loop (G).

   • Step C8: Install the bulb (not included) (Please do not exceed the maximum capacity recommended on the socket.)

5. Check everything is already installed properly, and then you can turn on the light. Enjoy!

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

References

• The domain name tape.be is for sale | Dan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>