TOUCHBeauty AG-2137 Portable Nail Drill User Manual
- June 15, 2024
- TOUCHBeauty
Table of Contents
TOUCHBeauty AG-2137 Portable Nail Drill
Safety Instructions
To ensure the proper operation of this device, please read this instruction manual carefully before using the device and keep it for further reference
WARNING
- The following persons should not use this device: children; persons with skin inflammation on the fingers or toes; persons with allergies; persons with reduced physical, sensory or mental capabilities: persons with diabetes.
- If you feel uncomfortable while using the device, please stop using it and consult a doctor.
- Do not use this device for any other purpose than nail care.
- Do not attempt to modify, disassemble, or repair the device by yourself.
CAUTION
This device has a lithium battery. Do not place or store the device for a long
time in a hot or humid environment. If you do not intend to use the device for
a long time, store ii after the battery is full.
Device Specifications
- Name: Portable Nail Drill
- Input: 7V= /800mA
- Power: 7V = /21W
- Type of Battery: Li-on 3.7V 800mAh
- Charging Time: 1.5h
- Working Time: 2 ~4h
- Charging Port: Type-C
- Wight: 130g
- Dimensions: 168 .. 24mm
Device Description
- Power Button/Pause Button/F or R Button
- Forward or Reverse Display
- Battery Display Light
- Speed Up or Down
- Bil Lock System
- Drill Bit (Suitable for 3/32″ Drill Bit)
- Five Speed-Settings Display
Preparation Instructions
- Charging the device: Connect the Type-C charging cable to the device charging port and to the adapter (not included) to start charging. The indicator flashes red while the device is charging and turns flashing green when the battery reaches >30%.
- The battery indicator flashes red when the battery is low. If the device runs out of battery, it will automatically shut down after the charging indicator flashes red for 10 seconds.
- Charging the device takes approximately 1.5 hours. A full battery allows for about 2-4 hours of continuous use.
- Installing 111e Drill Bits:
- Step 1 – Twist the bit lock system clockwise (about 90°) to unlock it.
- Step 2 – Remove the drill bit from the device.
- Step 3 – Insert the drill bit you want to use.
- Step 4 – Twist the bit lock system counterclockwise (about 90°) to lock the 111e drill bit in place.
How to Use
To ensure the correct operation of this device, please read the instructions carefully before use.
- Select and install the attachment according to your needs. To install the drill bit, push ii firmly into the top of the device until the head is firmly in place.
- Tum ON: Press and hok:J the power button for 2 seconds to turn ON the device, the nail drill starts rotating, and the R/F indicator lights up.
- Switch the Rotation Direction: With the nail drill ON, double-press the power button quickly to alternate between forward and reverse rotation. The F indicator lights up when forward rotation is selected and the R indicator lights up when in reverse rotation.
- Increase the Rotation Speed: Short press the “+” button each time you want to increase 1 level. The speed can be adjusted up to 5 times.
- Decrease the Rotation Speed: Short press the._ .. button each time you want to decrease 1 level. The speed can be adjusted up to 5 times.
- Pause the Device: If you need to stop using the device momentarily, short-press the power button. The nail drill stops rotating, and the device enters the standby mode. The standby mode has a duration of 120 seconds. If there is no operation during that time, the device automatically turns OFF.
- Turn OFF: After using the device, press and hold the power button to turn OFF the device. You can also press the power button to pause the device which will automatically turn OFF after 120 seconds.
- Use While Charging: You can use the device while it’s charging. You can also wait to use the device after it is fully charged.
- Motor Lock Protection System: If the nail drill touches a hard surface with pressure, all the light indicators flash continuously for 10 seconds, reminding you to lift the nail drill. tf you do not l ift the nail d rill from the surface,
the device automatically shuts down after 10 seconds.
Cleaning & Maintenance
- Make sure the device is powered off before you start cleaning.
- Do not immerse the device in water. The attachments can be cleaned separately.
- Clean the surface of the device with a clean, slightly wet cloth.
- Do not use lubricants, detergents, polishing agents, or air fresheners on this device.
Storage
This device has a lithium battery. Do not place or store the device for long
periods in a hot or humid environment. If you do not intend to use the device
for a long time, store it after the battery is full.
Recycling
This device’s built-in battery may contain substances that can pollute the
environment. When disposing of this device, remove the battery. Do not through
the device and battery into a fire or household waste. Please follow your
local government’s rules for the proper disposal of batteries to help protect
the environment.
After-Sales Service
Troubleshooting
Check this troubleshooting section if you are experiencing any of the
following issues. If you cannot find a solution and the problem persists,
please, contact our Amazon Customer Service.
-
Q: The device does not work
A: Check if the device needs to be charged; if the bit lock system is locked; or if the device is in pause mode. -
Q: The drill bit cannot fit the device, or it falls out.
A: Please check if the drill bit is correctly inserted and locked. You can also verify if the diameter of the drill bit is too large to f it the device bit entrance. -
Q: All device’s light indicators are flashing.
A: You are touching a surface that is too hard. You can increase the speed intensity or remove the grinding bit from the surface.
Important Safety Instructions
- “Warning – When using this product, basic precautions should always be followed
- Read all the instructions before use.
- Do not drop, knock, or disassemble the unit.
- Do not operate in wet or moist conditions.
- Do not use if it is damaged or modified in any manner.
- Do not be exposed to fire or extreme temperatures.
- Keep away from heat, flammables, poisons, and corrosive substances.
- Do not attempt to repair the appliance. If the device is damaged, it should be repaired or re-paced by an authorized professional.
- Dispose as per local law and regulations.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems) This marking on the
product, accessories or literature indicates that the product and its
electronic accessories should not be disposed of with other household waste at
the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and
recycle them responsibly to promote the sustainable reuse of material
resources. Household users should contact either the retailer where they
purchased this product, or their local government office, for details of where
and how they can take these items for environmentally safe recycling.
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>