PROGRESS LIGHTING 93166096_B 3 Light 17 inch Gilded Silver Pendant Ceiling Light Instruction Manual
- June 17, 2024
- PROGRESS LIGHTING
Table of Contents
P500443
3-L T MEDIUM PENDANT
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Glass Panel | 32 |
| C | Rubber Washer | 32 |
| D | Ball Nut | 32 |
| E | Stem | 1 |
| F | Canopy | 1 |
Ceiling mounting
-OR-
Hanging mounting
HARDWARE CONTENTS (not actual size)
THANK YOU for selecting Progress Lighting
We can assist you with questions regarding product information, assembly or
missing parts
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. You now need to adjust the screw length according to the fixture canopy depth.
-
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift up the fixture and pass the screws (AA) through the two mounting hole in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16 of threads are showing. That should be enough to mount the fixture as instructed in step 5 or step 11.
Next, take the fixture down and go back and tighten the
hex nuts (DD) up against the round mounting plate (CC). You now should have
the correct length of threads for mounting the fixture.
CEILING ASSEMBLY INSTRUCTIONS -
Pass the wires through the stem (E) and out of Canopy (F). Thread the canopy nipple (F) down onto stem (E). Thread the stem (E) down onto the fixture (A).
-
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
-
Attach canopy (F), two cylinder nuts (EE) to screws (AA). Tighten cylinder nuts (EE) to secure fixture to ceiling.
-
Slip the ball nut stud (D) through the rubber washer (C) and glass panel (B) and tighten it onto the fixture (A).
-
Thread lamps (not included} into the fixture sockets. Use 60-watt MAX incandescent candelabra base amps, SBCFL or SBLED.
HANGING ASSEMBLY INSTRUCTIONS -
Tighten chain loop (GG) onto the nipple of canopy (F).
NOTE: During this step, determine the hanging ength of your fixture by removing chain links. The electrical and ground wire may also optionally be cut to length.
Do NOT cut electrical or ground wires until this length is determined. Leave AT LEAST 6 inches
MINIMUM of wire past the canopy chain loop (GG) to allow for easy connections in step 10.
(Chain links can be spread open with 2 pairs of pliers.
Twist the split link ends in opposite directions and close by squeezing them back together.) -
Once hanging ength is determined, Pass wires through chain loop (GG) and tighten chain loop (GG) to stem of fixture (A).
Open chain link at one end of chain (FF). Hook the open chain link (FF) onto the chain loop (GG), Close the chain links back together with the pliers. Open the quick link (HH), Hook the quick link (HH) onto the other end of the chain (FF) and to the canopy chain loop (GG). Close the quick link (HH) and secure it tightly.
Continue to weave the wires through the chain links (FF) and up through the canopy loop (GG) -
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
-
Attach canopy (F), two cylinder nuts (EE) to screws (AA). Tighten cylinder nuts (EE) to secure fixture to ceiling.
-
Slip the ball nut stud (D) through the rubber washer (C) and glass panel (B) and tighten it onto the fixture (A).
-
Thread amps (not included) into the fixture sockets. Use 60-watt MAX incandescent candelabra base lamps, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects n material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers’ sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if t is shown to have been defective n material or workmanship at time of shipment. Progress’s sole and maximum iability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE}, WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. n no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer’s responsibility. Customer s responsible for determining the suitability of our products for customer’s use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.
93166096
800-447-0573
8am- 8pm (Eastern), Monday- Friday
customerservice@progresslighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>