iArmor IA-S071H-S195H 6.5 Inch Side Armor Stainless Steel Boards Instruction Manual

iArmor IA-S071H-S195H 6.5 Inch Side Armor Stainless Steel Boards

Product Specifications:

• Model: IA-S071H/S195H
• Mounting Type: Rocker Panel Mount
• Trimming may be required

Product Usage Instructions

Step 1: Mounting Brackets Installation
Start the installation from the driver’s side of the vehicle. Locate the tabs along the bottom edge of the body where the Mounting Brackets will bolt.

Step 2: Attaching Mounting Brackets
Attach the mounting brackets to the designated locations on the driver’s side using the provided hardware. Follow the instructions in Figs 1-5 for proper installation.

Step 3: Installing Driver Side Front Bracket
Secure the Driver Front Mounting Bracket using the provided hardware including Hex Bolts, Lock Washers, and Large Flat Washers.

Step 4: Repeat for Remaining Driver Side Brackets
Repeat the installation process for the remaining driver-side brackets using the same hardware and attachment method.

Step 5: Attaching Step Bar
Once all driver-side mounting brackets are installed, attach the Driver Side Step Bar onto the brackets using U Brackets, Carriage Bolts, Large Flat Washers, Lock Washers, and Hex Nuts. Do not fully tighten the hardware at this stage.

Frequently Asked Questions (FAQ):

• Q: Is trimming required for installation?
  A: Trimming may be required for proper fitment. Please refer to the instructions for more details.

• Q: Can I install the product myself?
  A: While self-installation is possible, professional installation is recommended for the best results.

• Q: What if I encounter difficulties during installation?
  A: For any installation issues or questions, please contact our customer support at info@iarmorauto.com.

BEFORE INSTALLATION

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. THANK YOU FOR CHOOSING OUR PRODUCT!

• ROCKER PANEL MOUNT
• TRIMMING MAY BE REQUIRED

Torque Value

PART LIST

Description

Hex Bolts
2#| 2| Passenger Center & Rear Mounting Brackets| 6#| 12| M8 Large Flat Washers
3#| 1| Passenger Front Mounting Bracket| 7#| 12| M8 Lock Washers
4#| 6| U Brackets| 8#| 12| M8 Clip Nuts

Hardware Package

INSTALLATION INSTRUCTION

The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation

• STEP 1

  • Start the installation from the driver’s side of the vehicle. Locate the 3 tabs along the bottom edge of the body, (pinch weld). Mounting Brackets will bolt to the 1st, 2nd, (just in front of center of cab), and 4th mounting tabs, (Fig 1). Directly above each tab is a top mounting location on the side of the body panel.
    NOTE : It will help identify the mounting holes to hold up a mounting bracket in place

• STEP 2

  • Determine the correct procedure for your model year and each Bracket location.
  • Bottom mounting location on the edge of the pinch weld.
  • Flat tab on pinch weld with factory-installed weld nut:
  • Thread M8 Hex Bolt into weld nut from the backside down to clear paint from threads, (Fig 2).
  • Flat tab on pinch weld with hole:
  • Select (1) M8 Clip Nut. Slide the M8 Clip Nut over the tab with the nut facing up behind the tab, (Figs 3—5). Line up the threaded nut with hole in tab. Repeat for each mounting location.
  • Top mounting location on the back side of the body panel.
  • Models with factory-installed threaded insert in body panel:
  • Thread M8 Hex Bolt into threaded insert to clear paint as required, (Figs 2 & 3).
  • Large and small hole in side of body panel:
  • Remove the rubber plug from the larger hole, (Fig 4). Select (1) M8 Clip Nut. Slide the M8 Clip Nut into the larger hole. Line up the threaded nut with the smaller hole, (Fig 5).

• STEP 3

  • Select (1) Driver Front Mounting Bracket, attach it to the installed M8 Clip Nuts and/or the factory threaded holes on Driver Side Front Mounting Location with (2) M8X1.25-25mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers, (Fig 6). Snug but do not fully tighten the hardware.
    Note : All (3) Driver side Mounting Brackets are Universal

• STEP 4

  • Repeat Steps 1-3 to install the (2) remaining driver-side Brackets.

• STEP 5

  • Once all (3) driver-side mounting brackets are installed, select and attach the Driver Side Step Bar onto the Mounting Brackets with (3) U Brackets, (3) M8X1.25-55mm Carriage Bolts, (3) M8 Large Flat Washers, (3) M8 Lock Washers and (3) M8X1.25 Hex Nuts (Fig 7). Do not fully tighten hardware at this time.
    NOTE : Torque all M8 X1.25-55mm Carriage Bolts to 16~18 Ib-ft. Don’t over-tighten, or the square bars will be damaged by the brackets

• STEP 6

  • Properly level and adjust the Step Bar and fully tighten all hardware.

• STEP 7
  Move to the passenger side of the vehicle. On the passenger side, determine if the vehicle is equipped with a plastic diesel exhaust fluid (DEF) tank, (Figs 8 & 9).
  Models without DEF tank, skip to Step 8.
  Models with DEF tank: The tank sits close to the side of the body. With specialized tools, the Passenger Front Mounting Bracket can be installed but room is limited. It may be easier to drop the tank down to access the inner side of the body panel for bracket installation. Tank will not need to be removed, only dropped down for access to mounting location. IMPORTANT: If tank is full, it will be very heavy and assistance is highly recommended to avoid injury or damage to the vehicle or the tank. It is recommended that installation is performed when the DEF tank is low on fluid before dropping the tank.

  • For 07-16 Models: with plastic lower tray under the tank, remove the (3) hex bolts attaching the tray to the frame, (Fig 8), and remove the tray. For 2017-Up 2500/3500 models: Remove the (4) hex bolts attaching the plastic cover to DEF tank, (Fig 9A) and remove the plastic cover, (Fig 9B).
  • Release the tank filler hose. Release the plug for the sending unit on the top of the tank.
  • Support the tank with a floor jack. Place a smooth flat surface, (wooden block for example), between the floor jack and the tank to avoid damaging the plastic tank. Do not push up on the tank; only support the weight of the tank with the jack.
  • Remove the (2) bolts securing the tank straps to the vehi-cle, (Fig 10). Tilt the straps to release from the brackets. Slowly lower the tank until the top of the tank is almost visible. Use blocks or stands to support the tank while installing the front Brackets.
  • Proceed to Step 8.

• STEP 8
  Attach the Passenger Front Mounting Bracket to the vehicle: pinch weld and top panel (Figs 11 & 12).

  • Models with flat tab and hole: see Fig 11. Leave loose at this time.
  • Models with weld-nut: see Fig 12. Leave loose at this time.

• STEP 9

  • Repeat Steps 1—3 for the (2) remaining passenger side Brack-et installations.
  • 2017-up 2500/3500 DEF tank models: Locate the 2nd tab bracket location along the bottom edge of the body, (pinch weld), (Fig 13). Hold the DEF cover in place and mark the 2nd Bracket location onto the cover, (Fig 14). Use a sharp knife or hacksaw blade to carefully cut a slot in the plastic cover to clear the 2nd Bracket, (Fig 15). Remove as little plastic as possible.

• STEP 10

  • Repeat Steps 5-6 to install the passenger side Running Board Installation

• STEP 11

  • Once the Running Board are installed and all hardware is fully tightened, reinstall the DEF tank and cover, if equipped, as described in Step 7.
  • The installation is completed.

Attention

• Do periodic inspections to the installation to make sure that all hardware is secure and tight.
• To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

Customer Support: info@iarmorauto.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>