DYNOJET PC6-17005 POWER COMMANDER 6 2012-2022 Kawasaki Ninja ZX-14R Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
PC6-17005 POWER COMMANDER 6 2012-2022 Kawasaki Ninja ZX-14R
Installation Guide
Installation Guide for PC6-17005
Model coverage: 2012-2022 Kawasaki Ninja ZX-14R
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 2 VELCRO STRIPS
- 1 ALCOHOL SWAB
- 1 POSI-TAP
- 3 ZIP TIES
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fly between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either Input 1 or Input 2. The
polarity of the wires is not important. Set to Input 2 by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
set up you can alter your map based on gear position and setup gear-dependent
kill times when using a quick-shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your fuel curve based on this input in
the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
| 1. Remove the left
and right side fairings, both inner fairings, the upper fuel tank cover, and
the ram air duct covers on both sides.
2. Remove the bolts that hold the coolant reserve bottle to the engine.
Let the bottle hang out of the way temporarily.
---|---
| 3. Disconnect the
stock wiring harness from the throttle body harness.
These connectors are GREY in color and are located under the throttle
bodies.
| 4. Lay the PC6 next
to the gauge panel temporarily and route the PC6 harness along the stock
wiring harness on the left side of the bike to the throttle body connection.
Use the supplied zip-ties to secure the PC6 wiring harness to the stock
wiring harness.
| 5. Connect the PC6
in line with the stock wiring harness and throttle body harness.
| 6. Use the supplied
Positap to attach the BLUE/ WHITE wire from the PC6 to the GREEN/RED wire of
the stock Gear Position Sensor.
The connector is located on the left side of the bike near the front
sprocket cover.
7. Route the remainder of the PC6 wiring harness with the 2-pin crank
connectors and ground lug under the throttle bodies to the right side of the
bike.
| 8. Locate and unplug
the bike’s Crank Position Sensor connectors.
This is a BLACK 2-pin connector under the #3 throttle body, that is taped to
the throttle body wiring harness. You can trace the wiring harness coming out
of the right-hand side flywheel cover to this connector.
| 9. Plug the PC6
wiring harness in line with the stock Crank Position Sensor connectors.
| 10. Secure the PC6
ground wire with the small ring lug to the stock ground bolt on the right-hand
side of the bike.
11. Reinstall the coolant reserve bottle.
12. Install the PC6 module to the left-hand ram air duct. Use the supplied
velcro to secure the PC6 module.
Clean both surfaces with the supplied alcohol swab prior to applying the
velcro.
| 13. Reinstall the
body panels.
NOTE: This bike uses a servo to hold the throttle plate open during cold
starts. If the throttle position needs to be reset, make sure the bike is
running at normal operating temperature before resetting the throttle position
in the PC6 software.
If you have a 2016+ model make sure to download the corresponding map for your
model.
Optional inputs:
Engine Temperature – ORANGE wire of temperature connector on the back of
cylinder #3
12v source for Auto-tune – BROWN/YELLOW wire of BLACK 10-pin connector,
located under LH ram air duct (near PC6 install)
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS,
NV 89081 – 800-992-4993
DYNOJET.COM
© 2007-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
12-22 KAWASKI ZX-14R
PC6-17005.01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>