SEALEY SA141 SQ Drive Air Impact Wrench Diesel Glow Plug Kit Instruction Manual
- June 17, 2024
- SEALEY
Table of Contents
** SA141 SQ Drive Air Impact
Wrench Diesel Glow Plug Kit
Instruction Manual**
SA141 SQ Drive Air Impact Wrench Diesel Glow Plug Kit
1/4”SQ DRIVE AIR IMPACT WRENCH DIESEL
GLOW PLUG KIT
MODEL NO: SA141
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP
THESE INSTRUCTIONS SAFE FOR FUTURE USE. 
SAFETY
Follow all Health & Safety and
general workshop rules, regulations and conditions when using the wrench.
WARNING! Disconnect from air supply before changing accessories or
servicing.
Maintain the wrench in good
condition and replace any damaged or worn parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Check correct air
pressure is maintained and not exceeded. We recommend 90psi.
Keep air hose away from heat,
oil and sharp edges. Check air hose for wear before each use and ensure that
all connections are secure.
Only use impact sockets which
are specifically designed for use with an impact wrench.
Wear approved safety eye/face
shield, ear defenders and hand protection.
Maintain correct balance and
footing. Ensure that the floor is not slippery and wear non-slip shoes.
Keep children and non-essential
persons away from the work area.
DO NOT use the wrench for a task that it is not designed to perform.
WARNING! DO NOT use wrench if damaged or thought to be faulty
(contact your Service Agent).
DO NOT use wrench unless you have been instructed in its use by a
qualified person.
DO NOT carry the wrench by the air hose, or yank the hose from the air
supply.
DO NOT operate the wrench if you are tired or under the influence of
alcohol, drugs or intoxicating medication.
To avoid unintentional starting
DO NOT carry the wrench with your finger on the trigger.
DO NOT direct air from the air hose at yourself or others.
When not in use, disconnect from
the air supply and store in a safe, dry, childproof location.
WARNING! – RISK OF HAND ARM VIBRATION INJURY
This tool may cause Hand Arm Vibration Syndrome if its use is not managed
adequately.
This tool is subject to the vibration testing section of the Machinery
Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 5.1m/s²
Uncertainty value (k): 1.0m/s²
Please note that the application of the tool to a sole specialist task may
produce a different average vibration emission. We recommend that a specific
evaluation of the vibration emission is conducted prior to commencing with a
specialist task.
A health and safety assessment by the user (or employer) will need to be
carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are
intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many
factors.
Such factors include; the operator, the task and the inserted tool or
consumable.
NB: ensure that the length of leader hoses is sufficient to allow
unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a
poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
1.1 HEALTH SURVEILLANCE
We recommend a programme of health surveillance to detect early symptoms of
vibration injury so that management procedures can be modified accordingly.
1.2. PERSONAL PROTECTIVE EQUIPMENT
We are not aware of any personal protective equipment (PPE) that provides
protection against vibration injury that may result from the Uncontrolled use
of this tool. We recommend a sufficient supply of clothing (including gloves)
to enable the operator to remain warm and dry and maintain good blood
circulation in fingers etc. Please note that the most effective protection is
prevention, please refer to the Correct Use and Maintenance section in these
instructions. Guidance relating to the management of hand arm vibration can
be found on the HSC website www.hse.gov.uk – Hand-Arm
Vibration at Work.
INTRODUCTION
Reduced torque impact wrench suitable for the removal of seized glow plugs on diesel engines. Features a 4-position air regulator which provides limited torque settings to suit. One-handed operation for trigger and forward/reverse control. Soft grip reduces vibration, chill effect and adds comfort. Handle exhaust helps to lower noise level during use. Includes fi ve deep impact sockets, extension bar and universal joint. Supplied with foam insert and metal storage case.
SPECIFICATION
Model No: …………………………………………………… SA141
Air Consumption: …………………………………………….. 5cfm
Contents: ……………………………………………………………….
1/4”Sq Drive Deep Impact Sockets; 8, 9, 10, 11, 12mm
50mm Extension Bar, 1/4”Sq Drive Universal Joint
Free Speed: ……………………………………………. 10000rpm
Inlet Size ……………………………………………………1/4”BSP
Noise Power/Pressure:………………………….. 102/91dB(A)
Operating Pressure ………………………………………… 90psi
Torque Settings ………………………………10, 20, 30, 40Nm
Vibration/Uncertainty: ……………………………… 5.1/1.0m/s²
AIR SUPPLY
4.1. Recommended hook-up is shown in fig 1.
4.2. Ensure that the wrench trigger is in the “Off” position before connecting
the air supply.
4.3. You will require an air pressure of 90psi and an air flow of 5cfm.
WARNING! Ensure that the air supply is clean and does not exceed 90psi.
Too high an air pressure and/or unclean air will cause excessive wear and may
result in damage and/or personal injury.
4.4. Drain the compressor air tank daily. Water in the air line will damage
the wrench.
4.5. Clean compressor air inlet filter weekly.
4.6. Line pressure should be increased to compensate for unusually long air
hoses (over 8 metres). Hose internal diameter and the bores of fittings should
be 1/4” minimum.
4.7. Keep hose away from heat, oil and sharp edges. Before each use check hose
for wear and make certain that all connections are secure.
OPERATION
WARNING! Ensure that you read, understand and apply safety instructions
before use.
5.1. Only use the impact sockets which are supplied with this tool or
those specifically designed for use with an impact wrench. DO NOT use worn or
damaged sockets.
5.2. Connect the wrench to the air supply as described in Section 4.
5.3. Place the socket over the top of the glow plug and depress the
trigger to operate the wrench.
5.4. To change rotation, push the slide button at the top of the handle.
Move it in the direction F for forward (clockwise) and in the direction R for
reverse (anticlockwise) see fig.3.
5.5. The torque may be regulated by adjusting the air regulator valve at
the base of the handle.
DO NOT allow the wrench to free run for an extended period as this may
damage the bearings.
MAINTENANCE
WARNING! Disconnect the wrench from the air supply before changing
accessories, servicing or performing maintenance. Replace or repair damaged
parts. Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
6.1. If the air supply system does not have an oiler, lubricate the
wrench daily with a few drops of Sealey air tool oil dripped into the air
inlet.
6.2. Clean the wrench after use.
6.3. Loss of power or erratic action may be due to the following:
A) Excessive drain on the air line. Moisture or restriction in the air pipe.
Incorrect size or type of hose connectors. To rectify, check the air supply
and follow instructions in Section 4.
B) Grit or gum deposits in the wrench will also reduce performance. If your
model has an air strainer (located in the air inlet), remove the strainer and
clean it. Flush the wrench out with gum solvent oil or an equal mixture of SAE
10 oil and paraffin.
Allow to dry before use.
6.4. When not in use, disconnect from the air supply, clean and store in
a safe, dry, childproof location. 
ENVIRONMENT PROTECTION
**** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 36 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park,
Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
SA141 Issue 3 (ALL) 17/07/23
Documents / Resources
|
SEALEY SA141 SQ Drive Air Impact Wrench Diesel Glow Plug
Kit
[pdf] Instruction Manual
SA141 SQ Drive Air Impact Wrench Diesel Glow Plug Kit, SA141 SQ, Drive Air
Impact Wrench Diesel Glow Plug Kit, Impact Wrench Diesel Glow Plug Kit, Wrench
Diesel Glow Plug Kit, Diesel Glow Plug Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>