Honeywell MPA2C3 MPA Series Access Control Panel User Guide

: May 15, 2024
: Honeywell

**Honeywell MPA2C3 MPA Series Access Control Panel User Guide

**

This guide describes the basic setup, wiring, and configuration steps for getting started with a MPA access control panel.

Setup Process

Step 1. Download the Device Utility App
Step 2. Preparing to Start up
Step 3. Connecting Devices
Step 4. Powering up
Step 5a. Connecting to MAXPRO Cloud
Step 5b. Setup Computer for Web Mode Connection
Step 5c. Connecting to the Panel in Web Mode
Step 5d. Connecting to WIN-PAK

Digital Manuals and manuals in other languages
Honeywell provides this manual in English and other languages on the following link:

Get Online Documents Here

The same links can be found on the product by scanning this QR code.

Note: UL certificate does not contain model MPA2MPSE/MPA4MPSE.

Download the Device Utility App

Note: Mobile device must have iOS 13 or Android 6 or higher.

Download the application from the App Store, or Play Store. Scan this QR code for the application in the App Store.

Get Device Utility App Here

Scan this QR code for the application in the Play Store.

Get Device Utility App Here

Preparing to Start up

Check DIP Switches SW1 default status. (Set Bit 3 and Bit 9 to ‘ON’.). For Default IP, set Bit 4 to ON. (see step 5)
a. Check/Connect the power 10 -19 VDC and battery 12 VDC, 7Ah-12 Ah, OR b. Connect the power POE+.

Note: Do not connect a backup battery when using PoE+.

Select/Check the host connection IP(Ethernet) Or USB.
Check the output jumper configuration.(12 VDC/Ext .V; NO/ NC) .

Connecting Devices

Check host Ethernet (RJ45) or Type-C USB connection.
Check/Connect the reader connections (OSDP/Wiegand) by RJ45, or MPA2RJ (RJ45 to 8 terminal block converter).
Check/Connect)the MPA2S5 cable to input/output devices (door status/door contact connection)(Push-in Terminal block or RJ45).

Readers	Conductors	Gauge	Distance
Wiegand	__ 6-8	18 AWG Shield 20 AWG Shield CAT6 CAT6a CAT7	350 ft.

Powering up

Power up the panel (10-19 VDC PSU, or PoE+)
a. Check Mains LED for PSU (Green ON), or b. Check PoE+ LED for PoE+ (Blue ON).

Note: Battery LED (Red ON) indicates the panel is powered by battery.

Check Running LED
- Blinking green for 2-door panel.
- Blinking orange for 4-door licensed panel.
Test credentials and readers (OSDP / Wiegand).

Power Requirements

MPA2 Reader Door Configuration

| Specification| MPA2C3 or MPA2C3-4
---|---|---
Outputs| Number of outputs| 4 SPST Door relays (Jumper- Selectable NO or NC Contacts) per door rated 3A @30VDC; 4 SPST Aux relays NO Contacts rated 3A @30VDC (NC selectable in software)
Door Relay Power Source| Selectable:12 VDC(max 750mA per 2 door outputs) internal power source, or external power source, max 3A @30VDC per output
Inputs| Number of Inputs| 8(+4) Configurable four-state supervised Input points (factory Default Settings are: Status, REX, Reader Tamper A, Reader Tamper B, Power Fail, General Inputs)
Panel Tamper (4X)| Panel Door, Off-Wall, internal back tamper and External Tamper
Metal cabinet Mains power input| Mains Inputs| 100 to 240 VAC, 1.1A, 50/60Hz
Socket or Hardware AC Inputs (IEC/UL)| MPA2MPSU or MPA4MPSU only
Power Inputs| Control Board Power Inputs| 13.8VDC ~3.3A from Included Power Supply Note: It is forbidden changing the PSU by user
Power Output (internal panel power)| Power for locks/Strikes/ Reader(s)/ Inputs Devices| 750mA per 2 doors for locks/strikes, 500mA per 2 reader ports
3A @ 12VDC total available power for all devices(internal PSU).

Hard Default Procedure

To hard default the MPA2 series panels to factory default:

Note:

Note down the existing settings on DIP Switch SW1.
When the panel is powered up, turn all DIP switches to the OFF position.
Power down, then power the panel back up.
Wait for the panel to completely restart. The RUN LED should blink fast.
Set the DIP switches (SW1) back to their original positions.
Power down, then power the panel back up.
The RUN LED should blink at a normal pace.

The panel is now reset to the original factory default values.

Note: When using the DIP switches to reset a panel to the original factory default values, the Event History is lost, and any customized databases are removed; the panel is reset with the original factory default database. This does not affect the Ethernet IP address.

Connecting to MAXPRO Cloud

The MPA2C3, or MPA2C3-4 panel is configured Plug & Play out of the box for MAXPRO Cloud connectivity (DHCP Server Required).

Configuration is not required in local web mode all settings are configured within the MAXPRO Cloud web user interface.

To use this panel on cloud requires a MAXPRO Cloud account.

Login to your MAXPRO Cloud account at: mymaxprocloud.com
Create and / or navigate to the Customer Account
Create and / or navigate to a Site
Click on ADD CONTROLLER button
Choose “MPA2”, OR “MPA4”, select “MPA2MPS(U/E)” OR “MPA4MPS(U/E)”
Type in the panel’s MAC ID, click **ADD CONTROLLER

**

Setup Computer for Web Mode Connection

Use the Device Utility App to set up the panel for Web mode operation.

Note: These steps are for computers with windows 10 operating system, or higher. The steps for other operating system might be slightly different.
Note: When connecting to USB, USB driver is required. Navigate to the Technical Support Self- Service/Download Center.
https://myhoneywellbuildingsuniversity.com/training/support/

Click Start > Control Panel.
Click Network and Sharing center.
Click change adapter settings.
Identify your local Ethernet connection(Local Area Connections) and double-click on the link.
Click Properties.
Highlight the Internet Protocol (TCP/IPv4).
Click properties. View your system current IP address.
Use the following IP address.
- Enter: 192.168.1.10* in the IP address field when connecting to Eth1/PoE+ – HOST .
- Enter: 192.168.2.10* in the IP address field when connecting to USB 2 – WEB MODE.
Enter: 255.255.255.0 In the Subnet Mask field.
Click OK; OK;Close.

Note: *IP address 192.168.1.10 only valid if default panel address is in use.

Connecting to the Panel in Web Mode

Launch the Google Chrome™ Browser.
Enter the panel’s IP address in the address box.
Connection Type:
- Eth 1 / PoE+- HOST: Default IP DIP Switch SW1, Bit 4 (ON) https://192.168.1.150
- USB 2 – WEB MODE (Fixed): https://192.168.2.150
Default Login.
- Username: admin
- Password: admin
Navigate to “Host” and select WEB.
To set the IP, navigate to Settings tab and configure a static IP Address, Subnet Mask and Default Gateway

Connecting to WIN-PAK

Use the Device Utility App to set up the panel for WIN-PAK operation.

In WIN-PAK.

Add panel as MPA-2-R3 or MPA-4-R3 in Device Map.
In the MPA2C3 / MPA2C3-4 Panel.
For easy connection, Use DIP Switch SW1, Bit 4 (ON) for default IP address.
Log into Panel’s Web interface.
Click Main Menu Icon.
Select Panel Configuration and Host / Loop Communications.
If not configured, select WIN-PAK and IP properties and Click Save.
Follow the TLS Encryption procedure from WIN-PAK manual.
Upload the TLS encryption file to the panel.
Switch DIP Switch SW1, Bit4 to OFF position.

Honeywell Omni Smart OSDP Configuration

Set the following in the reader tool.

Create a template selecting reader type as: HID Reader.
Profile: Standard profile
In credentials: Enable all credential type
Keys: No need to select anything.
Configure Reader settings:

BLE Settings: Default settings
Communication protocol:
- Enable OSDP
- Spec Compliance V1
- Address 1, 2, 3, or 4
- Baud rate: 9600

Add the above to template (using the menu).

Keypad Settings: Input Format: BCD -4 BIT, facility Code:0, Backlight LED Color: RED (default).

MPA2C3- Two Door OSDP Configuration

Configuration| Types| Reader| Reader/IU (Connector)| OSDP Reader Address| Wiegand
---|---|---|---|---|---
Door 1| 1 Direction| Reader A| Reader 1 IN| 1| No Hold line required, but can be connected
2 Direction| Reader B| Reader 1 OUT| 2
Door 2| 1 Direction| Reader A| Reader 2 IN| 1
2 Direction| Reader B| Reader 2 OUT| 2

Note: For OSDP reader addressing, the addressing tool in the panel can be used. Connect the readers one by one and assign the address to the reader.

Required OSDP Reader settings

AES Encryption: ON (OSDP V2)
Encryption keys: Default
Address: 1, 2, 3 or 4
Baud rate: 9600

Note: For OSDP reader addressing, the addressing tool in the panel can be used. Connect the readers one by one and assign the address to the reader.

MPA2C3-4 Four Door Configuration

Technical Support

Hours of Operation | Monday through Friday, 9:00 am – 7:00 pm EST
USA +1 800 323 4576 # Option 2
Technical Support, Option 2 (Access Control)
EMEA
Hours of Operation | Monday through Friday, 9:00 AM – 6:00 PM CET

Phone Support

EMEA ITALY +390399301301
UK +441344238266
SPAIN +34911238038
FRANCE +33366880142
THE NETHERLANDS +31108080688

E-mail Support

USA https://myhoneywellbuildingsuniversity.com/training/support
EMEA ITALY hsgittechsupport@honeywell.com
UK hsguktechsupport@honeywell.com
SPAIN hsgestechsupport@honeywell.com
FRANCE hsgfrtechsupport@honeywell.com
THE NETHERLANDS hsgnltechsupport@honeywell.com

Web Support
Technical Assistance & Schedule Support: https://buildings.honeywell.com
Mywebtech Customer Support:
https://myhoneywellbuildingsuniversity.com/training/support
Online Training: https://myhoneywellbuildingsuniversity.com
https://buildings.honeywell.com/
Honeywell Building Technologies
715 Peachstreet ST.NE
Atlanta, GA30308
USA
Honeywell Comercial Security
Carlton Park, BUilding 5
King Edward Avenue
Narborough,Leicester
LE193Q United Kingdom