zooz S2 On and Off Switch User Manual
- June 17, 2024
- ZOOZ
Table of Contents
S2 On and Off Switch
“`html
Specifications
- Model Number: ZEN76 800LR
- Region: US/CA/MX
- Power: 120 VAC, 60 Hz
- Maximum Load: 8 A, 150 W LED/CFL, 600 W
incandescent, 960 W
Product Usage Instructions
-
1. **Install the Wires:**-
UNSCREW: Carefully turn the screw
counter-clockwise to create space for the wire. Do not unscrew
completely. -
PRESS DOWN: Once loose, press the screw down
with your finger to catch the thread. -
INSERT WIRE: Ensure the wire is straight, then
insert it into the terminal while holding the screw down. Do not
wrap wires around the terminal screws. -
TIGHTEN: Turn the screw clockwise to tighten
the wire. Do not overtighten.
-
-
Complete Installation:
Secure the Z-WaveTM switch in the box with mounting screws,
handle wires carefully, install the wall plate, and restore power
to the circuit.
-
1. **Test the Switch:**
If the LED indicator lights up after turning on the power and
the switch is off, tap the upper paddle for ON and lower paddle for
OFF. If the test fails, check power restoration, wiring accuracy,
and load size.
FAQ
Q: What should I do if the LED indicator does
not light up after restoring power?
A: If the LED indicator does not light up,
ensure that power is fully restored to the circuit, wiring matches
instructions precisely, and the load is not too large causing
overheating of the switch.
Q: Can this switch be used with fluorescent
lighting fixtures?
A: No, this switch should not be used with
fluorescent lighting fixtures. It is recommended for LED and
incandescent bulbs only.
Q: How do I add this switch to my Z-WaveTM
hub?
A: To add the device to your hub, initiate
inclusion (pairing) in the app or web interface. Refer to the
provided QR codes or contact support for detailed instructions.
“`
USER MANUAL
HOW TO INSTALL THE WIRES
S2 ON/OFF SWITCH 800 ZEN76 800LR
1. UNSCREW: carefully turn the screw counter clockwise to make space for the wire. DO NOT
unscrew completely.
www.getzooz.com ask@getzooz.com
Scan to register your product for extended warranty and direct access to firmware files.
2. PRESS DOWN: once it’s loose, press the screw down with your finger so it catches the thread.
3. INSERT WIRE: make sure the wire is perfectly
straight, then insert it into the terminal while
STRIP WIRE AT 1/2-5/8″ holding the screw down. DO NOT wrap wires
around the terminal screws!
4. TIGHTEN: turn the screw clockwise to tighten
the wire. DO NOT OVERTIGHTEN!
FIRMWARE VER: 3.10
COMPLETE INSTALLATION
FEATURES
Secure your Z-WaveTM switch in the box with mounting screws,
Y Manual or Z-WaveTM on/off control with instant status updates Y 800 series Z-WaveTM chip for better range and faster control
handling the wires with care. Install the wall plate and restore power to the circuit.
Y Simple Direct 3-Way: connect with existing on/off switches in 3-
TEST THE SWITCH
way, 4-way, and 5-way set-ups, no add-on needed Y Scene control: trigger
actions with multi-tap (select hubs only) Y Smart bulb mode: disable relay and
control lights via Z-WaveTM Y Z-WaveTM Long Range for ultra reliable no-mesh
communication Y Adjustable LED indicator in 4 colors and 3 brightness levels
Y Works with LED and incandescent bulbs (don’t use with tubes)
The LED indicator should light up as soon as you turn the power
back on if the switch (light) is OFF. Tap the upper paddle for ON and lower
paddle for OFF. If the test fails, please check that: Y power is fully
restored to the circuit Y wiring matches the instructions exactly Y the load
isn’t too large and overheating the switch causing it to
SPECIFICATIONS
Y Model Number: ZEN76 800LR Y Region: US/CA/MX Y Power: 120 VAC, 60 Hz Y
Maximum Load: 8 A, 150 W LED/CFL, 600 W incandescent, 960 W
resistive (DON’T use with tube lights, fans, or receptacles) Y Range: Up to
500 feet line of sight Y Operating Temperature: 32-104° F (0-40° C) Y
Installation and Use: Indoor only
CAUTION
shut off
WARNING
Y This product should be installed indoors upon completion of any building
renovations. Y Prior to installation, the device should be stored in a dry,
dust-and-mold-proof place. Y Do not install the switch in a place with direct
sun exposure, high temperature, or humidity. Y Keep away from chemicals,
water, and dust. Y Ensure the device is never close to any heat source or open
flame to prevent fire. Y Ensure the device is connected to an electric power
source that does not exceed the
maximum load power. Y No part of the device may be replaced or repaired by the
user.
Z-WAVETM CONTROL
1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the app (or web
This is an electrical device – please use caution when installing and
interface).
operating the on/off switch. Remote control of appliances may result in unintentional or automated activation of power. Do not use this Z-WaveTM device to control electric heaters or other appliances which produce the risk of fire, burns, or electrical shock
Not sure how? Scan one of the QR codes below for step-by-step instructions or get in touch: www.support.getzooz.com
when unattended. To reduce risk of overheating and possible damage to other equipment, do not install this unit to control a receptacle; a motor-operated appliance; a fluorescent lighting fixture; or a transformer-supplied
2. Finalize inclusion at the switch. TAP UP 3 TIMES QUICKLY
if using traditional Z-WaveTM inclusion.
fixture.
SCAN THE QR CODE / ENTER THE 5-DIGIT DSK
BEFORE YOU INSTALL
if using the new SmartStart method.
The LED indicator will blink blue to signal communication and turn green
This switch is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a licensed electrician perform this installation.
for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails. SmartStart enabled products can be added into a Z-WaveTM network by scanning the Z-WaveTM QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and
WIRING: READ IT!
the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.
1. CHECK THE LOAD: lights only (150W for LED’s, 600W for incande-scent), DON’T CONNECT THIS SWITCH TO OUTLETS
NEED SOME HELP? ask@getzooz.com
OR TUBE LIGHTS.
Choose your hub and scan the QR code with your phone’s
2. POWER OFF: turn the circuit power off in the breaker panel camera. Then click on the link to access the step-by-step
before you start. If installing in a multi-switch box with
pairing instructions.
multiple circuits, turn power off at all of the circuits.
3. CHECK THE WIRES: mark load (most o en black), line
(most o en black), neutral (most o en white), and ground
(most o en bare). 14 AWG wires only! Don’t rely exclusively
on your multimeter to identify the wires!
µNOT SURE WHAT YOU’RE SEEING? WE’LL HELP! SUPPORT.GETZOOZ.COM SEND US PICTURES
OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES.
SmartThings
Hubitat
Home Assistant
Z-Box Hub
Get more tutorials and helpful tips at ww.support.getzooz.com
4. REMOVE THE OLD SWITCH: disconnect the wires and label them with the included label stickers. 5. CONNECT THE Z-WAVETM SWITCH: follow all installation steps carefully. Wire the switch EXACTLY like in the diagram.
TROUBLESHOOTING The switch won’t add to your system? Try this: 1. Initiate EXCLUSION and tap the lower paddle 3 times quickly. 2. Tap the upper paddle 4-5 times quickly when adding it. 3. Bring the gateway controller (hub) closer to the switch, it may
ZEN76 WIRING DIAGRAM FOR SINGLE POLE INSTALLATION
be out of range. 4. Get troubleshooting tips for your hub at
1 Insert the ground (bare) wire into the Ground terminal (not shown in the diagram) 2 Insert the power source wire to Line terminal and load
www.support.getzooz.com The switch won’t control the lights manually anymore? Try this: 1. Turn the power off at the breaker and check if a wire didn’t get
wire to Load terminal. Load and line CAN’T be swapped so make sure you identified them correctly!
loose. 2. Exclude the switch from the hub or reset it in case manual
control was accidentally disabled.
3. The load may be incompatible so try it with a single
incandescent bulb.
SEE BACK PAGE FOR 3-WAY & 4-WAY DIAGRAMS AND INSTRUCTIONS
3 Run the white jumper (included in the box) from the bundle of white wires to
the Neutral terminal
DON’T FORCE THE SCREWS. Look up to see how to install the wires correctly.
PAGE 1
EXCLUSION (REMOVING / UNPAIRING DEVICE)
1. Bring your Z-WaveTM gateway (hub) close to the switch if
possible 2. Put the Z-WaveTM hub into exclusion mode (not sure how
to do that? ask@getzooz.com) 3. Tap the lower paddle on the switch 3 times
quickly (the
LED indicator will start blinking blue)
4. Your hub will confirm exclusion, the LED indicator on the
switch will turn green for 3 seconds, and the device will
disappear from your controller’s device list
FACTORY RESET
If your primary controller is missing or inoperable, you may
need to reset the device to factory settings. To reset the
switch, press and hold the lower paddle for 10 seconds
until the LED indicator starts blinking. Release paddle, and
immediately a er, tap the lower paddle 5 times to
complete the reset. The LED indicator will flash blue 3 times
and turn red for 3 seconds to confirm successful reset.
NOTE: All previously recorded activity and custom settings will be erased from
the device’s memory.
PAGE 2
ADVANCED SETTINGS
Please refer to your controller’s user guide for advanced programming
instructions as they are a little different for every so ware. Not sure where
to start? Go to www.support.getzooz.com for detailed instructions on how to
change the settings on SmartThings, Vera, and more. Or just email us:
ask@getzooz.com
CUSTOMIZE YOUR SWITCH
Here is a selection of settings available to customize your switch. Scan the
QR code for a full list of parameters and look below for how to access them on
your hub. Y LED Indicator behavior, color, brightness: SCAN SETTINGS 6 x TAP
UP to change the indicator mode Y Smart Bulb Mode (disable the relay): HOLD UP
for 10 seconds then 5 x TAP UP Y On/off status a er power failure
Choose your hub and scan the QR code with your phone’s camera. Then click on
the link to learn how to access and change the advanced settings for the
switch on your hub.
SmartThings
Hubitat
Home Assistant
Z-Box Hub
SCENE CONTROL
You can trigger scenes or control other connected devices in your network
using this switch. Just enable the setting in Parameter 9 and confirm that
your hub supports scene control. Assign scenes or actions to 1-tap, 2-tap,
3-tap, 4-tap, 5-tap, held, and released for any of the paddles.
Scan the QR code for scene control programming instructions on your hub.
QUESTIONS? ask@getzooz.com
ASSOCIATION
This on/off switch supports Group 1 with up to 1 devices for Lifeline
communication and Group 2 with up to 5 devices. This device will send BASIC
REPORT to Group 1 and BASIC SET command to group 2 when operated manually. You
can set direct association to have the switch control another Z-WaveTM device
independently of the hub by using Group 2. Not every hub exposes direct
association settings in the interface so please go to www.support.getzooz.com
to see if your system allows for direct association.
S2
This product can be included and operated in any Z-WaveTM network with other
Z-WaveTM certified devices from other manufacturers and/or other applications.
All non-battery operated nodes within the network will act as repeaters
regardless of vendor to increase reliability of the network. This product
features the latest Security 2 (S2) framework to remove smart home network
hacking risks. This device is equipped with a unique authentication code for
trusted wireless communication. This is an ETL certified device. ETL, just
like UL, is a Nationally Recognized Testing Laboratory. The ETL mark is proof
of product compliance with North American safety standards.
WARRANTY
This product is covered under a 12-month warranty and under a 5-year limited
warranty once registered. To read the full warranty policy or file a warranty
claim, please go to www.getzooz.com/warranty
IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY
INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES
FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY,
WHETHER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DA-MAGES. ZOOZ’S LIABILITY AND CUSTOMER’S EXCLUSIVE REMEDY
FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE
OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH
OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY
LIMITED TO, AT ZOOZ’S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE
PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED.
ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE
OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY
(30) DAYS FROM ZOOZ’S DELIVERY, OR THE DATE FIXED FOR DELI-VERY IN THE EVENT
OF NONDELIVERY.
FCC NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN
NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR
USE WHERE DIRECTLY EXPOSED TO WATER. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following conditions: 1. This device
may not cause harmful interference, 2. This device must accept any
interference received, including interference that may cause undesired
operation. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used according to
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in any given
installation. If this equipment causes harmful interference to radio or
television reception, the user may try to correct the interference by taking
one or more of the following measures: – Reorient or relocate receiving
antenna – Increase the separation between equipment and receiver – Connect
equipment into a separate outlet or circuit from receiver – Consult the dealer
or an experienced radio/TV technician for additional assistance
All brand names displayed are trademarks of their respective holders. © Zooz
2023
PAGE 3
ZEN76 WIRING DIAGRAMS FOR THE MOST COMMON 3-WAY INSTALLATIONS
For more diagrams or to request custom instructions go to support.getzooz.com
ZEN76 / ZEN77
STOP!
Wire and screw position, as well as color codes are for illustration only. You
should not follow the colors and positioning in the illustration blindly.
Always identify all wires prior to installing Zooz switches and make sure you
can match the diagrams to your set-up exactly. Don’t experiment or attempt a
“trial-and-error” installation for your own safety.
NOTE!
If you are not comfortable identifying the wiring and completing the
installation, please consult a licensed electrician. Make sure you have
identified all wiring correctly before connecting the switch. If your wiring
doesn’t match any of the below diagrams, contact our support: ask@getzooz.com
ZEN76 / ZEN77
ON/OFF SWITCHES ONLY
Do not connect Zooz Z-WaveTM switches to an existing 3-way dimmer, illuminated
switch, or an electronic add-on switch. Zooz switches can only be wired with
mechanical on/off switches in a 3way or 4-way setting! To simplify the
diagrams, we did not include connections for the ground wire. Remember that
all Zooz switches need to be wired according to the electrical code, with
ground wire connected to the ground terminal. Always install your Zooz S2
switch in the box with direct connection to power line. Diagrams and
instructions in this manual are for ZEN76 and ZEN77 models ONLY!
ZEN76 WIRING DIAGRAM FOR THE MOST COMMON 4-WAY INSTALLATION
For more diagrams or to request custom instructions go to support.getzooz.com
NEED HELP?
If you’re having trouble reading the diagrams or don’t see your wiring set-up
here, get in touch! We have more 3-way, 4-way, and 5-way diagrams and
instructions. There are many ways to wire multi-point control set-ups so
unless you
can match your wiring to the diagrams here, please don’t
attempt the installation for your own safety.
www.support.getzooz.com ask@getzooz.com
ZEN76 / ZEN77
MORE COLOR?
The white paddles on the ZEN76 switch can be replaced for a different color!
Please get in touch with our support to check which colors are currently
available and how to order replacement paddles. Zooz switches will match the
shade of standard Leviton switches and wall plates available at any major
retailer.
RANGE TEST TOOL
You can now easily check if the switch is within your Z-WaveTM hub’s range:
Press and hold the lower paddle for 10 seconds until the LED indicator starts
blinking. Release the paddle and within 2 seconds, tap the lower paddle 2
times quickly. The LED indicator will then report signal strength. Solid green
= direct communication with the primary controller is stable Flashing green =
direct communication with the primary controller is established but signal is
weak Solid blue = stable communication with hub via repeaters Flashing blue =
communication with the primary controller is established via repeaters but
signal is weak Solid red = communication with the primary controller has
failed Tap the lower paddle to exit testing mode.
NOTE: This function may only be activated once the switch has been included to
a Z-WaveTM network.
The Simple Direct 3-Way/4-Way implemented in this device is a unique ZWave
multi-point control solution covered under U.S. Patent 10,219,353 B1.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>