QIDITECH X-Smart3 3D Printer User Guide

QIDITECH X-Smart3 3D Printer

Quick Start Guide

Usage Notice

• Do not place the machine in flammable and explosive materials or near high heat sources, please place the machine in a ventilated, cool and dust-free environment.
• The X-axis carbon fiber rod on the machine cannot be replaced, so please take care to protect it from scratching the carbon fiber rod and affecting printing.
• Ensure the machine is powered off(unplug power cord) before performing maintenance or modifications.
• Before connecting the power. please follow the power setup instructions to ensure that the voltage is correct.
• Never reach inside QIDI printer while they are in operation.
• Children should be under constant supervision when using QIDI products.
• The printer contains high-speed moving parts, so be careful of hands pinching.
• There is a potential risk of burns: the print heads of the QIDI printers can reach temperatures above 300 • C, while the hot bed can reach temperatures above 100
• Do not touch either of these parts with your bare hands.
• Do not place the printer in a vibrating or other unstable environment. Otherwise the shaking of the machine will affect the printing quality.
• After printing, use the residual temperature of the print head to clean the filament around the nozzle with the dedicated tools in time. Do not touch either of these parts with your bare hands.
• Regular maintenance will reduce the wear and increase the life of the printer. Regularly clean the carbon fiber rod with absolute alcohol or isopropanol, clean the printer body with a dry cloth, wipe off dust, bonded printing materials, and foreign objects on the Z axis. Always unplug QIDI products before performing maintenance or modifications.
• If the machine is in standby mode for a long time, please unplug the power of the QIDI products.
• If the machine is not used for a long time, please pay attention to protect the printer from dust and damp.
• There are manuals, slicer software and other related informations in the USB flash drive.
  (The information in the USB flash drive may not be the latest. You can obtain the latest information by contacting the After-sales Service marked at the end.)

Accessory List

Starting Up

Remove the upper foam and extract the printer.

Remove the power cord from the top cover foam and connect it to the printer. Switch on the printer and proceed with the on-screen instructions to complete the unpacking and calibration process. Attention: Please double-check that the voltage setting of the power supply aligns with the voltage standard of your region/country before turning it on.

Language

Please select your preferred language and click on the next step.

Unboxing

Follow the on-screen instructions to remove the four ties securing the platform in place.
Remove the ties fastening the extruder and X-axis, discard the cardboard, and proceed to the next step.
Note that the carbon fiber rod on the X-axis cannot be replaced, so handle it with caution to avoid scratching it and compromising print quality.

Follow the on-screen instructions to remove the four screws securing the printing platform in place.

Click “Next”. Make sure the print bed is unlocked and clear of any debris before proceeding.

Follow the instructions on the screen to remove the foam from under the printing platform and click next.”
Note that the foam may adhere to the underside of the platform.

Load Filament

Take out the filament support bar from top foam, and follow the instruction on the back side sticker to attach the support bar properly. Once attached support bar, place the filament onto the support bar.
Note that it is advised to fit the filament support cover to the support bar to prevent any potential dropping of the filament.

Follow the prompts displayed on the screen and insert the filament through the filament detection sensor up to the printhead. Ensure that the filament is properly fed into the printhead and click on the “next” button to proceed.

Enter the print temperature for the filament and press the Heat button. Allow the temperature to reach the preset value and then proceed to the next step.

Click the downwards button and allow the filament to emerge from the nozzle.
Notice: If there is no filament flow, even after multiple attempts, check that the filament is properly entering the printhead.

Click “Next” and finish the start guide.

First Printing

Please perform automatic bed leveling and input shaping before the first print to make the printing more better.
Note : Before any operation, make sure that the PEI build plate is on the print platform.

Choose a preset model and print it

Note: Built-in models use PLA Rapido filament by default. After the U disk is inserted into the machine, the U disk files are displayed in the sda1 folder.

Printer Introduction

How To Remove The Print Head Front Cover

Carefully push upward to unlock the front cover. then remove it.

X-Axis Cleanup

Wet the carbon fiber rods with alcohol or isopropanol, and gently rub the carbon rods to dean any debris with a dust-free cloth.

Wet the carbon fiber rod again, and move the print head right and left repeatedly to clean out the dirt in the print head bearing.

Wipe the carbon fiber tube with a cloth, and repeat steps 3 to 5 until there is no stain on the print head bearing and carbon fiber tube. After cleaning, perform resonance compensation once.
Note: The X-axis rod needs to be cleaned every 1-2 weeks.

Filament Guide For Beginners

Tips

1. Some other brands of ABS filaments are less heat resistant and it is recommended to set the chamber temperature no more than 55 degrees Celsius. Otherwise the filaments may be soften in advance and cause clogging.
2. If the filaments do not stick to the print platform:
3. Please check if the nozzle is far away from the print plate, you can adjust the platform upward by Offset adjusting function.
4. Because of the different ambient temperatures in different regions, the temperature of the heat bed can be increased appropriately to increase the adhesion of the filaments.
5.  If above all can not work , please contact the after-sales service for assistance.

Specifications

Body| Print Size (W”DH)| 175180170 mm
Dimensions| 370362*397 mm
XY Structure| Core XY
X Axis| 10mm Hardened Wear-Resistant Carbon Fiber Rod
Z Axis| Double Z Axis
Shell| Plastic
Chassis| Steel
Motor| 42-48 High-Speed Motor
Print Head| Print Head Temperature| :s 3so0c
Extruder Gear| Hardened Steel Gears
Transmission Ratio| 9.5: 1
Hot End| Circular Ceramic Heating Hot End Only need 405 Heating From 20°c to 220°c
Temperature Measurement Unit| Thermocouple
Nozzle| Brass Nozzles
Nozzle Diameter| 0.4mm
Filament Diameter| 1.75mm

Hot Bed

| Printing Platform| Aluminum Substrate Heating Bed
Printing Plate| Double-Sided Flexible Magnetic H F Plate
Hot Bed Temperature| :s 120°c
Speed| Printing Speed| 250-500mm/s
Maximum Printing Acceleration| 20000mm/sA2
Cool Down| Hot End Cooling Fan| Closed-Loop Control
Model Cooling Fan| Closed-Loop Control
Auxiliary Part Cooling Fan| None
Motherboard Fan| Open Loop Control
Chamber Circulation Fan| Closed-Loop Control
Chamber Temperature| 50°C Without Chamber Heating
Filament| Recommended Filament| PLA
Compatible Filament| PLA,ABS,ASA,PETG,TPU
Seal Print| Compatible

**** Sensor

| Broken Filament Detection| Support
---|---|---
Automatic Leveling| Support
Resonance Compensation| Support
Power Supply| Voltage| 100-240 VAC, 50/60Hz
Rated Power| 350W
Electronics| Display Screen| 4.3 Inch 480•272 Touch Screen
Storage| 8G EMMC and USB2.0 Flash Drive
Motion Controller| Dual-Core Cortex-M4
Application Processor| Quad-Core 1.5GHz Cortex-A53
Extruder Independent Processor| Dual-Core Cortex-MO+
WIFI| Wifi Frequency Bands| 2.4 GHz
Transmitter Power  (EIRP)| 18 dBm (MAX)
Protocol| IEEE 802.11b/g/n
Software| Slicer| QIDI Slicer and other third-party software, such as Ultimaker Cura, Simplify3D, PrusaSlicer, etc.
Operating System| Windows, MacOS, Linux

Note: Since the first layer is more affected by the temperature of the hot bed, the chamber heater starts working on the second layer by default.

Please visit the QIDI Tech official Wiki for more machine usage and maintenance tutorials. https://wiki.qidi3d.com/en/home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>