Sunnydaze DECOR HDC-192 All Star Bowl Fountain with LED Lights Instruction Manual
- June 17, 2024
- Sunnydaze DECOR
Table of Contents
Sunnydaze DECOR HDC-192 All Star Bowl Fountain with LED Lights
Specifications
- Product Name : All-Star Bowl Fountain with LED Lights
- Model Number : HDC-192
FAQ
- What should I do if my fountain is making excessive noise?
- If your fountain is noisy, try tapping the pump gently or adjusting water levels to reduce noise. Contact customer service if issues persist.
- Can I return the product if there are defects?
- Defective products within the warranty period can be replaced at the discretion of Sunnydaze Decor. Contact customer service with proof of purchase and defect photos for assistance.
Review all assembly and care information carefully before using this product.
Save this manual for future reference.
Select a smooth, level surface to place the fountain. Assemble components on a
soft, clean surface to avoid damaging the finish.
| Parts | Qty. |
|---|---|
| Fountain Topper | 1 |
Fountain Body with Built-in
Electric Submersible Pump
| ****
1
AC Adapter| 1
IMPORTANT NOTES
- The water tubing is built into the fountain topper. Take care when handling the water tube; detaching the water tube from the fountain topper will damage the unit and void the warranty.
- Familiarize yourself with the flow control valve on the pump, maximum (+) and minimum (-). This may need to be adjusted to achieve optimal water flow.
- The lights and light cables are rated for contact with water. Use care when handling the lights, jarring movements or dropping them may cause the lights to burn out prematurely.
ASSEMBLY
-
Carefully unwrap the pump that is inside the fountain. Then, attach one of the light cables on the pump to the light cable inside the water reservoir.
-
Connect the remaining three pump cables to the light cables on the underside of the fountain topper.
-
Firmly attach the pump to the tubing that is built into the fountain topper; it will be a tight fit. Gently place the topper on the fountain body.
-
Fill the water reservoir with enough water to keep the pump fully submerged during operation.
NOTE: Ensure the water level does not exceed the rubber seal inside the water reservoir, the rubber seal will not completely prevent water from leaking. -
Connect the AC adapter to the pump power cable.
-
Plug the adapter into a properly grounded GFCI outlet.
NOTE: When first used, there may be air trapped inside the pump. It may take several minutes for trapped air to escape, allowing water to flow. Refer to page 2 for more troubleshooting tips.TE: When first used, there may be air trapped inside the pump. It may take several minutes for trapped air to escape, allowing water to flow. Refer to page 2 for more troubleshooting tips.
Care & Maintenance
- Some splashing may occur; adjust the flow rate on the pump if the water rate is too high. Do not use the fountain in areas that can be damaged if water happens to splash or leak.
- Some climates and weather conditions increase water evaporation, requiring water to be added more frequently.
- Frequently check water levels during times of high temperatures, wind, and long-term exposure to direct sunlight to ensure the pump remains underwater. Never allow the pump to run dry as it will burn out the motor.
- Only use water in this fountain. Distilled water will help prevent mineral buildup but is not required. Tap water is okay to use, but avoid heavily chlorinated water as it may damage the fountain and the pump.
- Periodically change the water to help keep the fountain and pump clean. Remove scale and buildup regularly.
- DO NOT use harmful additives such as bleach, chlorine, etc.
- DO NOT use anything abrasive to scrub the fountain.
- DO NOT use a pressure washer to clean the fountain.
- Always unplug the power supply before cleaning and maintaining the fountain and the recirculating pump. Take care when handling the pump; only pick it up by the body of the pump, never the power cord.
- During freezing weather, drain the fountain, disconnect the pump and store it indoors; allowing ice to form may damage the fountain in such ways as, but not limited to, fountain cracking, permanent pump damage and/or lighting malfunction.
- Over time, the finish may gradually mellow in colour due to sun exposure; this is part of the natural aging process and is not cause for return.
Troubleshooting
- If water is not flowing within several moments of the fountain being plugged in, ensure that the pump is fully submerged underwater. Add water to the reservoir if necessary. The pump may have air bubbles trapped inside, which can prevent water from circulating properly. Unplug the power supply for a few moments and plug it back in.
- Check the flow control on the body of the pump, it may need to be adjusted to achieve the desired water flow rate.
- Inspect the pump and tubing for obstructions.
- Pump noise can be caused by trapped air, low water level, or the pump being too close to the walls of the fountain.
- While the pump is fully submerged, try gently tapping the pump with your finger to help release the trapped air. Also, check if adding water or moving the pump helps to reduce noise.
- If water is not flowing and the lights do not turn on, ensure the AC adapter is fully connected to the pump power cable. If the pump is running but the lights are not working, ensure the cables are fully connected, and the seals are adequately tightened (do not over-tighten). Ensure the connector ends are completely dry before connecting and plugging the power cord back into an outlet.
- Check to make sure the power outlet is working; consult a certified electrician if in doubt about electrical connections.
If you experience issues with assembly or the product was damaged during
shipping, please contact our customer service team through one of the methods
mentioned at the top.
Please have the item number and order information ready to expedite response
time.
IMPORTANT SAFETY INFORMATION
- Fountains may splash or leak; always protect surfaces that can be damaged by water.
- Prevent water loss or damage to electrical sockets by ensuring the power cord has a drip loop; a diagram of a drip loop is shown on the right.
- Keep the fountain out of reach of children and pets.
- Make sure the power cord is away from traffic areas.
- Keep the power cord away from all heat sources. Do not use electrical cords in areas with high temperatures.
- Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as it will burn out the motor.
- Always unplug the power supply before cleaning and maintaining the fountain and the recirculating pump.
- Always empty and store the fountain and pump indoors during freezing weather.
- Do not use the fountain in areas that can be damaged if water splashes or leaks.
Drawing is for visual reference only, cord placement and plug type vary by fountain style.
Any modification to the product or failure to follow recommended care will void the product warranty.
WARNING
Manufacturer and seller expressly disclaim all liability from personal injury,
property damage or loss, whether direct or indirect, or incidental, resulting
from the incorrect attachment, improper use, inadequate maintenance, or
neglect of this product.
Purchase Date:…………………….Order/Customer Reference Number……………………..
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the
quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year
warranty period. Proof of purchase, with the date of purchase as well as
photos of the merchandise defect, must be provided. Photos are used to
determine the cause of defects and for future quality control. Register your
warranty at https://tiny.cc/SunnydazeWarranty. If you have any questions,
comments or concerns, feel free to contact us by phone at
833-982-1977, by email:
customerservice@sunnydazedecor.com.
or via our Contact Us page at https://tiny.cc/SunnydazeContact.
SunnydazeDecor.com.