AQUA-AMP AA-015-ACT 15W Wireless Charger Instruction Manual

June 14, 2024
AQUA-AMP

AQUA AMP logo AA-015-ACT 15W Wireless Charger
Instruction Manual

AA-015-ACT 15W Wireless Charger

AQUA AMP AA 015 ACT 15W Wireless Charger

Installation Instructions:
15W Wireless Charger

Parts Provided

|
---|---
Wireless Charger| Self tapping Screw (x4)

Tools Required

AQUA AMP AA 015 ACT 15W Wireless Charger - Tools
Required

Technical Information

Input Voltage Range 10-30V DC (12 / 24V system)
Input Current Max 2A
Output Power Max. 15W (9V, 1.66A)
Standby current Draw <0.3W
Waterproof rating IPx6
Certifications Qi, CE, FCC, ROHS

Installation Guide

Step 1: Identify the installation location. The installation location should be an area that (1) is flat, allowing the back of the charger to be completely flush with the surface it is being mounted to and (2) is large enough to will allow the arms of the charger to reach its fully extended length (approximately 8.25″).
Step 2: Place the provided alignment template in the installation location, using tape to secure it (if necessary). After double checking alignment and placement, use a drill and ‘4’ drill bit to drill the hole for the wire and a 3/32” drill bit to  drill pilot holes for the screws. Remove the alignment template when completed.
Step 3: Insert the installation fixture into the charger.
Thread the wire through the %” hole drilled in Step 2 and check for alignment of all four pilot holes to the mounting holes on the charger. Screw the charger in place using the provided screws. Remove the installation fixture and test that  the arms extend and retract as expected using your phone.
Step 4: Using a 2A fuse, attach wires to a 12/24V power supply and ensure there is a waterproof connection Step 5: Make sure the charger was connected correctly by placing a wireless charging compatible device in the center of the charger. Check that the device is charging a few seconds after you place it on the wireless charger.

The product must be installed according to the specified instructions. Failure to comply may result in personal injury, vessel/vehicle damage, and/or product failure. Installation by a trained electrician is recommended by Aqua Amp. Damage and/or injuries caused by improper installation are not covered by the warranty.

WARNING:
Only a 12V DC or 24V DC battery/power supply should be used with this device.
Before installing, the power supply must be turned off.
Between the battery/power supply and the product, an appropriate fuse or circuit breaker must be utilized.
Before turning on the electricity, double-check that all wiring is polarized correctly. High voltages may be included in this product. Do not alter the product in any way. This product is not intended for use in potentially hazardous or flammable environments.
Do not install in a hazardous/flammable environment, such as engine rooms. Make sure the space behind the mounting point is clear of wires, fuel, and any other potentially hazardous things before drilling any holes.
Ensure that any holes cut do not considerably degrade the surface’s structure. If the product must be installed outside, it must be installed safely above the waterline and not in danger of being submerged.
A metallic surface prevents the product from charging.

CAUTION:
The item is designed to charge Qi compatible devices only.
The cable must be kept in place and not obstruct mechanical systems.
There are no user-serviceable components in this product. In no way attempt to repair or modify the product.
The device’s high friction top surface does not guarantee that it will not slip during strong acceleration and deceleration working situations.
A phone case thicker than 3mm may prevent the smartphone from charging.
The product may temporarily shut down if used in a hot environment or in direct sunlight; this is a safety feature of the electronics.
The IP rating is only valid if the instructions are followed correctly. Avoid mounting near heat-radiating appliances and in poorly ventilated spaces when choosing a placement.

EMC INSTALLATION GUIDELINES:

To ensure that electromagnetic interference between equipment is minimized, Aqua Amp devices comply with Electromagnetic Compatibility (EMC) requirements. To keep electromagnetic interference to a bare minimum, proper installation is essential.
WIRING: When extending the wire from your battery/power source to the product, make sure there is a continuous supply of at least 10V. For any length of cable extension, we recommend an 18AWG (0.82mm2) wire gauge. This diagram shows how the product should be linked to a 12V or 24V DC battery or power supply.
ENVIRONMENTAL PROTECTION:
Electrical trash should not be thrown out with household garbage. Please recycle wherever possible. For recycling advice, contact your local government or a merchant.
IMPORTANT:
Aqua Amp LLC disclaims all liability for any injuries or other damages resulting from the use of their products in any situation.
WARRANTY:
The non-transferable 2-year warranty covers only this Aqua Amp product and not any devices mounted in or on it. Users’ devices are not covered by a guarantee, and they subject

FCC WARNING:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body. FCC ID: 2A64NAA-015-ACT
Aqua Amp LLC certifies that this product complies with the EMC CE-RED Directive (2014/53/EU) and the EN 62368 standard. The CE compliance certificate can be accessed at aquaamp.com. them to known and unknown hazards at their own risk.

AQUA AMP logoContact:
orders@aquaamp.com
1108 Eldridge St, Clearwater, FL 33755
For further information visit www.aquaamp.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals