ENTES ETMO-10 ETMO Ethernet Gateways Instruction Manual

ENTES ETMO-10 ETMO Ethernet Gateways

Specifications:

• Device Connection: RS-485 A(+)B(-), GND, RS-232 RX TX, PC Micro USB, Ethernet
• Supply Voltage Range: 85-265 VAC/DC
• Digital I/O Operating Range: 5-30 VDC

Product Usage Instructions

Device Connection:
Connect the device using the following ports: RS-485 A(+)B(-),GND, RS-232 RX TX, PC Micro USB, and Ethernet.

Power Supply:
Ensure the device is supplied with a voltage within the range of 85-265 VAC/DC.

LED Indicators:

• Status LED:
  • Red – On: Device energized but IP not received yet.
  • Green – On: Device energized, IP received (access WEB interface).
  • White Flasher: Reset factory settings (In progress).
  • Yellow – On: USB connected.
  • Red and Blue Sequential Flasher: Device malfunction, contact customer service.
• Ethernet LED:
  • ON: Connection is ON
  • Flasher: Connection is ON, communication is available.
  • OFF: Connection is OFF
• Digital Input LED:
  • ON: Digital input ON
  • OFF: Digital input OFF
• Digital Output LED:
  • ON: Digital output ON
  • OFF: Digital output OFF

Setting Interface:
To configure device settings via the web interface, connect it to a computer using a micro USB cable. Access the interface via http://usb.entes or 192.168.7.1. The device’s password is the last 4 digits of the MAC ID.

FAQ:

Q: How do I access the device settings?
A: Connect the device to a computer via a micro USB cable and access the web interface using http://usb.entes or 192.168.7.1. Use the last 4 digits of the MAC ID as the password.

Q: What should I do if the device malfunctions?
A: If the device malfunctions and the Red and Blue LEDs flash sequentially, please contact ENTES Customer Service for assistance.

Device Connection

Make the MODBUS connection of the device and make the Ethernet connection. The device’s supply voltage range is 85-265 VAC/DC. Supply the device with a suitable voltage within the supply range.

Connection Diagrams

LED Indicators

Status LED

• Red – On: The device is energized but IP has not been received yet, so you will not be able to access the WEB interface.
• Green – ON: The device is energized and IP has been received. You could connect to the WEB interface.
• White Flasher: Reset factory settings (In progress)
• Yellow – ON: USB connected.
• Red and Blue Sequential Flasher: Device has malfunction. Please contact ENTES Customer Service.

Ethernet LED

• ON: Connection is ON
• Flasher: Connection is ON, communication is available.
• OFF: Connection is OFF

Digital Input LED

• ON: Digital input ON
• OFF: Digital input OFF
• Digital Output LED
• ON: Digital output ON
• OFF: Digital output OFF

Setting Interface

In order to configure the device settings from the web interface, it must be connected to the computer with a micro USB cable. Then you could access the interface via http://usb.entes or 192.168.7.1. The device’s password is the last 4 digits of the MAC ID. You could check the device’s connection status to GSM on this interface.

Attention

• Modbus adresses of all devices connected to the modem must be different from each other and the serial port settings must be same. (Baudrate, parity, data bit, stop bit)
• Make sure the accuracy of serial communication line terminals (A-B-GND) between the data receiving devices and the device.
• Energized ETMO-02 models do not allow to read any address other than the first two different addresses.
• Make sure the IP settings of the device are suitable for your network structure (subnet mask, gateway address, DNS, IP address).
• If there is any firewall at your network, make sure the communication port (502 or 700) is available.

IT Instructions:
Share this information with your IT authorized or technical personnel responsible for internet access.
If you wish to access any ENTES service via static IP address by your internet provider (TCP server, static IP communication);
Give access authorization over default port 502 or the relevant port you configured.

ENTES Elektronik Cihazlar Imalat ve Ticaret A.S.
Adr: Dudullu OSB; 1. Cadde; No:23 34776
Ümraniye – İSTANBUL / TÜRKİYE
Tel: +90 216 313 01 10 Fax: +90 216 314 16 15
E-mail: iletisim@entes.com.tr – contact@entes.eu
Web: www.entes.com.tr – www.entes.eu
Call Center Technical Support: 0850 888 84 25

References

• ENTES Elektronik - Anasayfa
• ENTES Elektronik - Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>