SPRT SP-POS5813 Wholesale Super Light Weight Printer User Manual

POS Thermal Receipt Printer
SP-POS5813/POS5814

User’s Manual
(Ver 1.00)
Beijing Spirit Technology Development Co.,Ltd.
www.sprt-printer.com

Introduction

SP-POS5813/POS5814 printer is a new type line thermal printer, it features in fast speed print, low print noise, high reliability, perfect print quality and ribbon needless, avoiding the vexation of regular maintenance.
SP-POS5813/POS5814 printer: small in outline dimension, simple operation, and extensive application, especially suitable for commercial cash register, PC- POS, bank POS and all kinds of receipts print.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Feature and Performance

1.1 Print Performance

• Print method: direct thermal

• Print paper width: 57.5 ±0.5mm

• Print density: 8 dots/mm,384 dots/line

• Print speed: max 90mm/s

• Reliability
  (1) Print head life: 50km
  Using condition:
  ＊Print 12 × 24 ASCII characters, print 50 lines each time, intermittent print repeatedly
  ＊No more than 25% of each dot line can be printed simultaneously, and the same dot of each character line can be printed vertically no more than 11 times.
  ＊Use specified thermal paper
  (2) Cutter life: 1500,000 cuts

• Valid print width: 48mm

1.2 Print Paper
Paper Type: Thermal Paper 79.5 ±0.5mm xф80mm（max ）
Paper Thickness: 0.06mm ～0.08mm
Paper Loading Method: Easy loading
Paper Cutting Method: Manual

1.3 Print Font

• ANK Character Set
  12 ×24 dots,1.5 （W ）×3.00 （H ）mm.

• GB GB2312-80(Chinese):
  24 ×24 dots,3.00 （W） ×3.00 （H ）mm.

1.4 Interface

• Communication Interface:
  USB Interface(Type B, Female)
  Parallel(DB25, Male)
  Serial(RS232, P/S2)
  Bluetooth(BTDM, BTMM)
  Ethernet Interface: Normal Ethernet interface.

• Cash Drawer Control:
  DC12V, 1A, 6-pin RJ-11 socket.

1.5 Print Control Commands

• Character print commands: support double-width, double height print of ANK characters, user-defined characters and Chinese characters, the character line spacing is adjustable.
• Graphics print commands: support the print of bit-map graphics and download bit-map graphics with different density
• GS barcode print commands:
  support UPC-A, UPC-E, EAN-13 ，EAN-8, CODE39, ITF25, CODEBAR, CODE93, CODE128

1.6 Power Supply

• DC8.5V, 2A

1.7 Operation Environment

• Operation temperature: 0 ～50 ℃; Relative humidity: 10 ～80 ％
• Storage temperature: -20 ～60 ℃; Relative humidity: 10 ～90 ℃

1.8 Outline Dimension & Weight

• Dimension: 120(L)mm ×100(W) mm ×95 (H)mm
• Weight: 280g(without paper roll)

Operation Instructions

2.1 Printer Appearance
Printer appearance As shown in Figure 2-1-1, Figure 2-1-2.

2.2 Paper Installation
SP-POS5813/POS5814 printer adopts 58mm width thermal paper.
The thermal paper installation steps are as follows:

1. When there is no paper in the print head, please do not press the feed button to avoid affecting the life of the print head. As shown in Figure 2-1-1, hold the paper cover and pull it upward to open the door and change paper.
2. Do not manually pull the paper forward or stuff the paper backward after the paper cover is closed.

2.3 Interface
2.3.1 Communication Interface

1. Standard Type-B USB.
   PIN NO| Function| Note
   ---|---|---
   1| V Bus| The power supply is +5V.
   2| Data –| The data is negative.
   3| Data +| The data is positive.
   4| GND| Power ground
2. Standard DB25 parallel port connector, male plug.

pins| Definition| Description| Pins| Definition| Description
1| STROBE| Active low signal for data transmission| 14| Auto Feed| Automatically insert a line break for every carriage return in the printer
2| D1| The first bit of data.| 15| nError| Low-level indication indicates the presence of an error state.
3| D2| The   second   bit    of data.| 16| Prime|
4| D3| The third bit of data.| 17| Select Input|
5| D4| The forth bit of data.| 18| GND|
6| D5| The fifth bit of data.| 19| |
---|---|---|---|---|---
7| D6| The sixth bit of data.| 20| GND|
8| D7| The seventh bit of data.| 21| GND|
9| D8| The eighth bit of data.| 22| GND|
10| nACK| Response signal| 23| GND|
11| BUSY| Busy    signal,    active high| 24| GND|
12| Paper End| Paper     out     signal, active high| 25| GND|
13| Select| High-level message indicates that the printer is online.| | |
3. RS232 interface
Insert the dedicated DB9-P/S2 cable and follow the instructions on the self- test page to configure the serial port.

Pin| Definition| Description
1| RS323_RX| Serial Data Receiving
2| RS323_TX| Serial Data Transmission
3| RTS| Request     to     send     low effective.
4| CTS| Cancel        sending       low effective.
5| GND|
6| GND|
4.  Bluetooth（BTDM，BTMM）
Turn on the Bluetooth on the terminal device, search for the corresponding device based on the Bluetooth information on the self-check page, and input the password to connect to the device.
Note:
① The “POWER” light of the device will blink within the first 30 seconds after powering on; once Bluetooth is successfully connected after 30 seconds, this light will stay on.
② Bluetooth information can be set through the settings software.

5.  Ethernet
   ① Insert the Ethernet cable, enter the settings mode, refer to section 2.4.3, item 2, and select “Enable DHCP with 5-second delay confirmation”. The device will automatically obtain an IP address and save it, which will be used as the device’s static IP address thereafter.
   ② Use the settings software to configure the corresponding IP address.
   Note: When the router’s network segment changes, or when there is an IP address conflict within the local area network, the settings need to be reconfigured.

2.3.2 Cash Drawer Interface
The cash drawer interface of the SP-POS5813 printer adopts an RJ-11, 6-pin socket, as shown in Figure 2-3-1.

The pin definitions are as follows in Table 2-3-2:

Tabel 2－3－2 Definition of Cash Drawer Interface Pin
2.3.3 Power Connection
SP-POS5813/POS5814 printers are externally powered by a dedicated DC 8.5V/2A power supply.
2.4 Buzzer, Buttons and Indicators

2.4.1 Power ON/OFF
The power switch controls the power on/off status. When the device is turned off, pressing the power button will turn it on. Pressing the power button again will turn it off.
2.4.2 Feed Button
as the paper feed key, can be used for function settings and paper feed.

1. Under normal operation, pressing the key on the printer will feed the paper, and releasing the key will stop the paper feed.
2. Function selection

2.4.3 combination button

1. While the printer is out of paper and powered off, press and hold down the without releasing it. Then, briefly press the and wait for the prompt sound “Beep…beep…”. Release the to enter upgrade mode.
2. With paper loaded and the printer powered off, press and hold the button without releasing it. Then, briefly press the button   again and wait for the prompt sound “Beep…beep…beep…”. Release the button to enter function setting mode. Press the button briefly once to print the corresponding functions prompt: “Print self-test, hexadecimal mode, restore factory settings, dynamic IP acquisition (UE model)”. The confirmation will be automatic after a delay of 5 seconds.

2.4.4 Indicator lights and buzzer.

1. Green: Indicates the power switch status, stays on when the device is turned on.
   Note: Within the first 30 seconds of turning on, this light will flash; after 30 seconds of turning on, it will stay on constantly once the Bluetooth connection is successful.

2. The red light and buzzer indicate error statuses. When the printer is working normally, the red “STATUS” indicator light will be off. If this light begins flashing, it indicates an abnormal warning status.

The buzzer can be set to enable or disable error alerts through parameter settings. When enabled, it will be used to indicate the type of error status, which is the same as the “STATUS” indicator light.
When the error indicator light is blinking and the buzzer is sounding (when enabled), it indicates that the printer has encountered an error. The specific type of error can be indicated by the different patterns of blinking.
The error status indicators are shown in the following table.

paper, will resume normal operation once paper is available.
Flash twice, off for about 1 second.| Beep twice, pause for about 1 second.| The head is overheating, please wait for the engine temperature to decrease. It will automatically resume once the temperature is normal.
Flash three times, off for about 1 second.| Beep three times, pause for about 1 second.| The head heating plate is damaged and cannot be restored. It needs to be repaired.

Table 2－4

2.5 Self-Test
Self-testing can check whether the printer is working properly. In self- testing, the software version number, interface form, character configuration information, etc. are sequentially printed. If the self-test can correctly print out the self-test sample, it indicates that other parts of the printer are working properly except for the communication interface with the host. Otherwise, maintenance is required.
Self-testing method: With paper loaded and the printer turned off, press and hold the key, release within 3 seconds, and the printer will print out the self-test list.
2.6 Enter program upgrade model
Refer to section 2.4.3, step 1, to upgrade by selecting the appropriate interface and program file using the “UpdateFirmware” software.
Note: Parallel port models cannot be upgraded using a “USB to Parallel Port cable.”
2.7 Hexadecimal Printing
In reference to 2.4.3, Item 2, the three lines of prompts printed in hexadecimal mode are as follows:
Hexadecimal Dump
To terminate hexadecimal dump, Press FEED button three times.
Under this mode, all inputs will be printed as hexadecimal numbers. Press the key to feed paper for each line, repeat this process for a total of 3 times. Then, print “ Completed ” and exit the hexadecimal print mode.
2.8 Restore factory settings
Reference 2.4.3, item 2, only restore the printing configuration information, do not restore the Bluetooth and network configuration information.

Printer Driver Installation

To install the SP-POS5813/POS5814 series printer driver, please download it from our official website at www.sprinter.com.cn. Follow these specific steps:

1. Go to the homepage and navigate to the Download Center.
2. Select “Driver Programs” and then choose “POS Printer Series.”
3.  Download the driver program named SP-DRV211.

During the installation process, make sure to select the printer model as “58 Thermal Series.” For further instructions on how to install and use the driver program, please refer to the installation guide provided.

Performance Specifications

Specifications

**** Print Performance Specifications:

| Printing Method| Thermal Line
Resolution| 8 dots/mm (203dpi)/ 384 dots/line
Printing Speed| 90 mm/s
Effective Printing Width| 48mm
Paper Width| 57 .5mm±0.5mm
Print Support Features| Custom  character printing| Support
Graphics Printing| Support for printing graphics with different dot densities and downloading bitmap images for printing.
Chinese| GB2312-Level 3 Character Library: 24×24 dot matrix
English| ASCII: 9×17 dot matrix, 12×24 dot matrix
**** Barcode| UPC-A；UPC-E；EAN-13；EAN-8；CODE39； CODE93； CODABAR；ITF25； CODE128
Interface| USB, Serial, Parallel, Bluetooth, Ethernet, cash drawer
Support function| Paper shortage alarm, overheat protection, buzzer
Cash drawer control| DC12V, 1A, 6-pin RJ-11 socket
**** Power Supply| Direct    current   power supply| DC8.5V，2A

Paper

| Paper Type| Normal thermal paper 58×Ø 60mm
**** Paper Thickness| 0.06mm～0.08mm
| Paper loading| Easy paper loading
---|---|---
Paper Cutting Method| Manual

Physical properties

| Dimension| 120mm×100mm×95mm    (L×W×H)
**** Weight| 275 g （no paper roll）

Environmental factors

| Work  environment temperature/humidity| 0-50°C (working environment temperature) / 10-80% (relative humidity)
Save  environment temperature/humidity| －20～60℃（Save environment temperature）/10～90% (relative humidity)
Life span / Reliability| TPH| **** 50km

STATEMENT
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

References

• Printer Thermal, Thermal Receipt Printer, Mini Thermal Printer - SPRT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>