SMAJAYU R26 Tractor Auto Steer System Instruction Manual
- June 17, 2024
- SMAJAYU
Table of Contents
SMAJAYU R26 Tractor Auto Steer System
Product Information
Specifications
-
R26 Device:
- Height: 139mm
- Maximum Diameter: 136mm
-
Data Cable:
- Plug Types: POW/COM, DC power supply, DB9 data
configuration, USBD raw data export
- Plug Types: POW/COM, DC power supply, DB9 data
-
Power Adapter:
- Input: British Standard Plug
- Output: DC Plug
-
Radio Antenna:
- Frequency: 450-470MHZ
- Dimension: 280mm
Product Usage Instructions
R26 as Base Station
To set the R26 as a base station, follow these steps:
- Install SMAJAYU Survey software on your Android device.
- Proceed with the software setup instructions provided.
- Ensure that the R26 is powered on and properly connected to the necessary devices.
- Configure the R26 settings according to your specific requirements.
- Verify the connection and functionality of the base station.
-
R26 Device Usage
The R26 device comprises various components for different functions. Refer to the user manual for detailed instructions on using each component. -
Data Cable Connection
- Connect the data cable to the appropriate ports on the R2 device and other peripherals securely to ensure data transfer reliability.
-
Power Adapter Setup
- Plug the power adapter into a suitable power source following the specified input and output requirements to power the R26 device.
-
Radio Antenna Installation
- Mount the radio antenna within the recommended frequency range and dimensions for optimal signal reception.
Frequently Asked Questions (FAQ)
-
Q: What protocols are supported by the R26 when used with other radio RTK?
A: The R26 supports TRIMTALK, TRIMMK3, TT450S, and TRANSEOT protocols. Ensure protocol consistency when using with other devices. -
Q: How do I turn on or off the still recording mode on the R26?
A: Press and hold the still recording button on the R26 for 4 seconds to toggle the still recording mode on or off.
R26 base manual
(For JY305)
R26 Device
Device List
Device Hardware
- Ⅰ. R26
- Height 139mm.
- The maximum diameter 136mm
Data Cable
- POW/COM plug which connects to R26.
- DC power supply plug.
- DC power supply plug.
- USBD raw data export and save plug.
Power Adapter
- Input: British Standard Plug.
- Output: DC Plug.
Radio Antenna
- Frequency: 450-470MHZ.
- Dimension: 280mm.
Device Box
R26 Main Body:
Figure 6 R26 Main Body
- 9 PIN aviation plug, including power supply, COM RS232, CONFIG RS232.
- UHF radio antenna interface.
Fixed Thread: Five-eighth inch thread.
R26 as base station
- NOTE:
- When using with other radio RTK, you need to pay attention to whether the protocol is consistent. R26 supports TRIMTALK, TRIMMK3, TT450S, and TRANSEOT protocols.
Set R26 as base station
-
Set R26 as base station
Download link:
https://www.dropbox.com/sh/7d7d6xsrdklztu0/AAAf-lXBKxn0ExzJISoD1za3a?dl=0 -
Set up and start R26, open the survey software (make sure the device where the software is located has turned on Bluetooth): Device –> Communication –> Device Para –> Select your device number (same as SN) –> Connnect.
-
Device –> Base –> Select the channel and frequency –> Set Base Startup
Tip : If there is no protocol option in the software, please try to set the base station with default parameters first. After successful reset, you can see the options of the protocol.
-
After the base station is set up successfully, you can use the autopilot software to connect to the base station.
For detailed operation, please refer to the radio service part of ‘4.3 Base
station connection’ in “JY305 Operational manual”
Tip : The channel and protocol selected by the autopilot software must be
the same as the channel and protocol of the base station
Address: 8
- Room 213-214, Building 1, Mingliang Science Park, No. 88, Zhuguang North Road, Taoyuan Street,
- Nansh an District, Shenzhen
- Web： www.smajayu.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>