EMOS P56000S Flood Sensor User Guide

EMOS P56000S Flood Sensor

Specifications

• Enclosure rating: IP65
• Acoustic signalisation: > 85 dB at a distance of 1 m
• Power consumption: < 20 A in standby mode, < 65 mA in alarm mode
• Transmission frequency: 2.4 GHz, 25 mW e.i.r.p. max., Zigbee 3.0 protocol
• Weight: 49 g

Product Usage Instructions:

Sensor Description:
The Flood Sensor is designed to detect water leaks or floods and trigger an alarm when water is detected.

Pairing with the App:

1. Open the app and tap on “Smart.”
2. Tap the “+” icon in the bottom right corner and select the green lightbulb icon for flood sensor.
3. Follow the on-screen instructions to confirm detection state and set battery voltage percentage.
4. Complete the settings and confirm to create a scenario.

Creating Scenarios:
To receive info messages regarding alarm states or low batteries:

1. Tap “Smart” in the app.
2. Tap the “+” icon and select the flood sensor.
3. Confirm detection state and battery voltage percentage.
4. Tap the phone icon and complete settings.
5. To delete a scenario, tap the pencil icon and confirm deletion.

Deleting a Scenario:

1. Tap on the scenario you want to delete.
2. Tap on the delete option and confirm deletion.

Mobile Application:
Control the sensor using the EMOS GoSmart app available for iOS and Android devices. Log in if you have an existing account or sign up to create one.

Pairing with Zigbee Gateway:
If not already paired, follow these steps:

1. Plug in power cable to gateway and enable GPS and Bluetooth on your mobile device.
2. In the app, tap “Add Device” and select the Smart Multi Gateway IP-1000Z icon.
3. Follow the on-screen instructions, enter Wi-Fi network details, and pair within 2 minutes.

Description of the App’s Main Menu:

• Sensor status (normal or alarm mode)
• Record history
• Scenario creation for alarm states or low batteries
• Battery status – alerts when voltage drops below 2.44 V or during an alarm activation

FAQ

Q: What should I do if the detector fails to pair with the app?
A: If pairing fails, repeat the process ensuring you are not using a 5 GHz Wi-Fi network.

This manual contains important safety information regarding the installation and operation of the sensor. Read the manual carefully and store it safely for future use.

Technical information

• Operating temperature and humidity: 0 °C to
• +50 °C, 5 % to 95 % (without condensation) Enclosure rating: IP65
• Acoustic signalisation: > 85 dB at a distance
• of 1 m
• Power consumption: < 20 μA in standby mode,
• < 65 mA in alarm mode
• Transmission frequency: 2.4 GHz, 25 mW e.i.r.p.
• max., Zigbee 3.0 protocol
• Power supply: 1× 3 V CR2
• Dimensions: 18 × 75 mm
• Weight: 49 g

Sensor Description

• 1 – LED
• 2 – loud siren
• 3, 4 – water sensor
• 5, 6, 7 – screws
• 8 – pairing button
• 9 – battery

Pairing with the App

Creating Scenarios

In order to see info messages regarding alarm state or low batteries, you must first create a so-called Scenario in the app.

1. Tap Smart in the app, tap + in the bottom right corner and then tap the green lightbulb icon.
2. Choose the flood sensor, confirm the detection state and set the battery voltage percentage.
3. Confirm and tap the phone icon and complete the settings.
4. If you want to delete a scenario, tap the pencil icon in the top right and confirm deletion.

Deleting a Scenario

Mobile Application
The sensor can be controlled using a mobile application for iOS or Android. Download the EMOS GoSmart app for your device.

Tap the Log In button if you‘ve used the app before.
Otherwise, tap the Sign Up button and register.

Pairing the Zigbee Gateway with the App
(If you‘re already using the gateway, skip this step)

• Plug a power cable into the gateway and enable GPS and Bluetooth connection on your mobile device. Tap Add Device in the app.
• Tap the GoSmart list on the left and tap the Smart Multi Gateway IP-1000Z icon.
• Follow the instructions in the app and enter the name and password for your 2.4 GHz Wi-Fi network.
• The gateway will pair with the app within 2 minutes.

Note : If the gateway fails to pair, repeat the process and check the settings using the manual for the gateway. 5 GHz Wi-Fi networks are not supported.

Pairing the Detector with the App

• Unscrew the back cover and place a battery in the sensor.
• Long-press the pairing button (5 seconds) or touch both water sensors 3× with wet fingers or a wet pad over the course of 2 seconds.
• The green LED will start flashing – pairing mode has been activated for 2 minutes.
• Tap Add Device in the app.
• Tap the GoSmart list on the left and tap the Flood sensor P56000S icon.
• Follow the instructions in the app and enter the name and password for your 2.4 GHz Wi-Fi network.
• The detector will pair with the app within 2 minutes; the green LED will stop flashing.
• Replace the back cover.

Note: If the detector fails to pair, repeat the process. 5 GHz Wi-Fi networks are not supported.

Description of the App‘s Main Menu

1. Sensor status (normal or alarm mode)
   • the app displays a warning message in the event of alarm activation
2. Record history
   • shows the history of alarms/low battery states
3. Scenario creation
   • must be set in order for the device to send info messages about alarm states or low batteries
4. Battery status
   • the app will show a low battery warning message when voltage drops below 2.44 V.
   • the detector evaluates the voltage level of the battery every 12 hours or during every alarm activation.

For more detailed settings, see Creating Scenarios.

Commissioning

• Remove the 3 screws on the underside of the flood sensor, remove the cover and insert a battery.
• Use an alkaline battery only; never use a rechargeable battery.
• Make sure to insert the battery properly and with the correct polarity!
• Replace the cover.
• Test the flood sensor – put both water sensors in contact with water by, for example, touching them with wet fingers, or place the flood sensor on a wet towel with the water sensors facing down.
• An acoustic and optical alarm will activate.

Sensor Placement
Place the flood sensor onto a flat, non-conductive surface in the immediate vicinity of a critical spot where a water leak might occur, such as next to a washing machine, dishwasher, water tap, boiler, windowsill etc.. The sensor should be located in a visible place.
The sensor is designed for indoor use only.

ATTENTION: the flood sensor only detects the presence of liquid that has reached the water sensors.

Alarm Warning

• If a water leak is detected, the flood sensor will start emitting an acoustic + optical signal.
• The flood sensor will start continuously beeping and flashing its red LED at the same time.
• A water leak alert will be displayed in the app.
• The acoustic signal of the alarm cannot be temporarily silenced or turned off.
• Hereby, EMOS spol. s r. o. declares that the radio equipment type P56000S is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.emos.eu/download.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>