morphy richards MRICE45BK Commercial Ice Maker Instruction Manual

morphy richards MRICE45BK Commercial Ice Maker

Specifications

• Model: MRICE45BK
• Colour: Stainless Steel
• Rated Power: 300W
• Rated Voltage & Frequency: 220-240V~ 50Hz
• Rated Current: 2.0A
• Ice Bin Capacity: 13kg
• Refrigerant/Refrigerant Amount: R290/60g
• Foaming Agent: C5H10
• Dimensions (W x D x H): 445 x 403 x 795mm
• Net Weight: 27kg

Product Overview

The commercial ice maker features a top cover with a sliding door, air inlet, control panel, front housing, drainage outlet, water inlet, air outlet, power supply, ice scoop, drain pipe, throat clamp, and inlet steel hose for efficient ice production.

Control Panel Functions

• POWER: Used to turn the unit on or off.
• MODE: Allows selection between ice making mode, pre-shut off mode, and CLEAN mode.
• Clean: Initiates the cleaning mode for the appliance.
• Time: Used for setting delayed start time function.
• Size: Adjusts the size of the ice produced by the machine.

Control Panel Usage

To start the ice making process, press the POWER button. You can adjust settings like delayed start time and ice size using the corresponding buttons on the control panel. Follow the instructions provided in the manual for detailed steps on each function.

Frequently Asked Questions

Q: How do I clean the ice maker?

A: To clean the ice maker, follow these steps:

1. Press and hold the MODE button for 3 seconds to enter CLEAN mode.
2. Follow the cleaning instructions as outlined in the manual.
3. Press and hold MODE again for 3 seconds to exit CLEAN mode.

Q: How can I adjust the ice size?

A: To adjust the ice size produced by the machine:

1. Press and hold the – button for 3 seconds to activate the ice size function.
2. Use the + or – buttons to adjust the size.
3. Press MODE to confirm the selection or wait for auto-confirmation.
4. To cancel this function, press and hold – for 3 seconds.

Model: MRICE45BK

INSTRUCTION MANUAL
Read these instructions carefully before using this appliance for the first time.

STORE THESE INSTRUCTIONS CAREFULLY

For product hints and tips plus more join us at www.morphyrichards.com.au

facebook.com/MorphyRichardsAUS
instagram.com/morphyrichardsau

IMPORTANT SAFETY INSTRUCTIONS

WARNING
To reduce the risk of fire, electric shock, injury to persons or damage to property, follow basic precautions including the following:

• WARNING: Misuse of appliance could cause personal injury.

• WARNING: Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

• WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

• WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

• WARNING: Do not damage the refrigerant circuit.

• WARNING: Do not pour coloured drinks or congee drinks into the machine (including the water tank and ice tray).

• WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

• WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

• WARNING: When disposing of the appliance, do so only at an authorized waste disposal centre. Do not expose to flame.

• WARNING: It is hazardous for anyone other than an Authorised Service Person to service this appliance. In Queensland
  the authorised Service Person MUST hold a Gas Work Authorisation for hydrocarbon refrigerants to carry out servicing or repairs where the gas system is being opened or charged.

• DANGER: Risk of fire or explosion. Flammable refrigerant used. To be repaired only by trained service personnel.
  Use only manufacturer authorized service parts. Any repair equipment used must be designed for flammable refrigerants. Follow all manufacturer repair instructions. Do not puncture refrigerant tubing.

• WARNING: This appliance contains a quantity of R290 refrigerant which is flammable.

• WARNING: Risk of fire or explosion. Dispose of refrigerator properly in accordance with the applicable federal or local regulations. Flammable refrigerant used.

• WARNING: Risk of fire or explosion due to puncture of refrigerant tubing; follow handling instructions carefully. Flammable refrigerant used.

• WARNING: Keep clear of obstructing all ventilation openings in the appliance enclosure or in the structure for building-in.

• WARNING: Do NOT use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

• WARNING: Do not damage the refrigerating circuit.

• WARNING: Do not use electrical appliances inside the ice maker.

• If the refrigerant circuit should be damaged:

• Avoid opening flames and sources of ignition.

• Thoroughly ventilate the room in which the appliance is situated.

• Do not remove any safety, warning, or product information labels from the ice maker.

• Check the ice maker to ensure it is in good condition and that there is no damage to the ice maker, power cord or plug.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

Location

• Before using the Ice Maker for the first time, please wait 2 hours after positioning it.
• For indoor use only. Do not use outdoors or near water.
• Always locate your appliance away from the edge of the worktop.
• If the ice maker re-used after a period of time in storage, do not use for a few hours, allowing the unit to warm up to the room temperature before operating.
• Keep the appliance 15cm from other objects to ensure the heat generated is heat released.
• Never store or use gas and other flammable articles near the ice maker to avoid a fire.

Power cord

• WARNING: When positioning the appliance, ensure the power cord is not trapped or damaged.
• The power cord should reach from the socket to the appliance without straining the connections.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Remove the plug from the socket, grasp the plug and pull out the power cord, do not pull on the cord directly.
• Do not let the cord hang over the edge of a table or counter and keep it away from any hot surfaces.
• Do not let the cord run across an open space e.g. between a low socket and table.

Personal safety

• WARNING: To protect against fire, electric shock and personal injury do not immerse cord, plug and appliance in water or any other liquid.
• WARNING: The appliance surface is subject to residual heat after use.
• WARNING: Fill with potable water only.
• The temperature of accessible surfaces may be high when the appliance is operating.
• Unplug from the outlet before before moving or cleaning to avoid damaging the refrigerating system.
• Do not move the appliance while switched on.
• Do not use accessories which are not recommended by the manufacturer.
• Do not touch the evaporator when using the ice maker as the user may suffer from frostbite.

Electrical requirements

• WARNING: This appliance should NOT be used with extension leads and/or power boards.
• Check that the voltage on the rating label of your appliance corresponds with your house electricity supply which must be A. C.
  READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

SPECIFICATIONS

PRODUCT OVERVIEW

CONTROL PANEL

BEFORE FIRST USE

1. Remove all packaging materials and read all instructions.
2. Check that all accessories are complete and the appliance is not damaged.
3. Clean all parts to remove any dust or manufacturing residue.
4. The ice maker should be placed on a level surface. Adjust the four black feet on the bottom of the unit until it is stable and even.
5. The incline angle of the ice maker should not exceed 45°during transportation or use. Do not turn the ice maker upside down. Doing so could cause the compressor or refrigerating system to operate incorrectly. Please allow time for the liquid in the compressor to settle after the ice maker is moved or transported. Before using the ice maker for the first time, please wait for 2 hours after the unit has been positioned on a level surface.
6. The appliance must be placed on a dry and level surface with sufficient ventilation, far from heat sources such as ovens, heaters and corrosive gases. Leave around 15cm clearance on all sides of the ice maker for proper ventilation.
7. Do not fill the water reservoir with cold or hot water. This may damage the ice maker. It is best to fill the water tank with water that is from a tap or room temperature. The water quality added to the tank should be drinkable.
8. It is recommended the minimum inlet water pressure is 0.04MPa and maximum inlet water pressure is 0.8MPa.
9. Do not use the appliance at a very cold environment (lower than 8°C).
10. Clean the unit by following the operation of “CARE & CLEANING” on page 12 before operating.

USING YOUR ICE MAKER

See below connection instructions before first use.

1. Connect the quick connector to the water inlet port on the rear of the unit.
2. Screw an end of the inlet steel hose to the quick connector of the unit and ensure the Blue plastic lugs are securely fastened.

3. Screw the other end of the inlet steel hose to a 25mm water supply tap connector.

NOTE: If you wish to attach a longer inlet hose, you can purchase a 25mm thread pipe nipple joiner and 12mm wide inlet hose from a hardware shop and connect the two inlet hoses.

4. To connect the water drain pipe. Place the throat clamp on the thicker, textured end of the drain pipe. Then insert the thicker end with throat clamp of the drain pipe onto the drainage outlet on the rear of the unit. Turn the throat clamp key clockwise to tighten.

5. Put the thinner end of the drain pipe into the drain or sink. WARNING: Due to the small working space, be careful not to hurt your hand when tightening the clamp.

6. Turn on the water supply, visually check whether there is water leakage at the connection, if there is no water leakage, connect the appropriate power supply and then turn on.
   IMPORTANT: The water pressure of the main water supply system must be 0.04-0.8MPa at least.

7. Connect the unit with power source, the unit will go into Standby mode and will display “–”.
   NOTE: If the ice maker has been moved, allow it to rest for 30 minutes before powering on.

8. Press the POWER button to start the ice maker and water will begin to fill the machine and start the ice making process.

9. When a cycle of ice making has completed, the next cycle will begin. At this time, the NTC sensor will determine the time to make the ice, according to the ambient temperature. After a minute, the minutes remaining will show on the display. In the last minute, the seconds will countdown until the ice making cycle finishes.

10. The unit will continue to make ice until the ice shovel can not reset automatically, at this time, the ice basket is full and the ice full indicator illuminates solidly.

11. Remove the ice in the ice basket with the ice scoop accessory. After 15 seconds, the unit will begin to work again.

12. When ice needs to be removed, push the door until it is fully opened, and remove the ice according to your requirements with the ice scoop. This can be transferred to a freezer if needed for use later.

13. If you need to adjust the ice thickness, press & hold the – button for 3 seconds to activate the ice size function. Adjust the size by pressing + or – and press MODE to confirm the selection, or wait 10 seconds and the unit confirms the selection. See page 8 for more details.

14. To make the unit start working at a preset time automatically, press & hold the + button for 3 seconds to activate the time function. Adjust the time by pressing + or – and press MODE to confirm the selection, or wait 10 seconds and the unit confirms the selection. The ice maker can be programmed to start from 1 hour up to 48 hours. See page 8 for more details.
    NOTE: Refer to page 8 for more information on the control panel.

CARE & CLEANING

NOTE: In order to keep the ice cubes fresh and the ice maker in good condition, please perform the following cleaning process when the clean indicator flashes.

NOTE: If the appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the lid open to prevent mold developing within the appliance.

NOTE: It is recommended to use a Nickel Safe Ice Machine Cleaner in the water tank manually before cleaning with a ratio of 236ml of cleaner to 11.4L of water.

1. In the standby mode, Press & hold the POWER button to enter into the CLEAN mode, and the CLEAN indicator illuminates solidly.
2. The unit starts to be rinsed repeatedly for about 15 minutes.
3. The above cleaning process is automatic and does not require human involvement. The water pump runs for 4 minutes and then stops for 1 minute and is repeated 3 times.
4. The cleaning process is completed. The unit goes into standby mode (the cleaning process lasts for about 30 minutes).
5. Open the door and locate the drain plug and unplug manually to allow the water to drain (see below).

6. Rinse the ice basket with warm water.
7. Install the drain plug back in position, and the cleaning is completed.
   NOTE: Please empty the water in the unit, wipe it with a clean cloth and store it well if the unit will not be used for a long time.
   WARNING: Do not clean the ice maker with any flammable fluids. The fumes may create a fire hazard or explosion.

TROUBLESHOOTING

2.  Check the drain plug for any water leakage.

E2| Malfunction of the solenoid valve.| Contact the relevant Customer Care Centre.
E3| NTC malfunction.| Contact the relevant Customer Care Centre.
E5| Malfunction of the float switch.| Contact the relevant Customer Care Centre.

MAINTENANCE

If the unit fails to operate efficiently, is broken or other problems arise, unplug and do not operate.
Ask for advice by calling your local after sales service agent or the Customer Care Centre on 1300 556 816 (AU) / 0800 666 2824 (NZ).

WARRANTY

Please refer to the warranty letter in the box for warranty information. For any troubleshooting advice, please contact the relative Customer Care Centre below.

Glen Dimplex Australia Pty Ltd 8 Lakeview Drive,
Scoresby 3179, Victoria Australia
Ph: 1300 556 816

Glen Dimplex New Zealand Ltd 38 Harris Road, East Tamaki, Auckland 2013
New Zealand
Ph: 0800 666 2824

Recycling: Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water, polluting the food chain and damaging health and wellbeing.
Expanded Polystyrene Disposal: The websites listed below can assist in the responsible disposal of EPS (Expanded Polystyrene) packaging products.
Australia: https://recyclingnearyou.com.au/polystyrene and/or http://epsa.org.au
New Zealand: https://greenbusinesshq.com/epsrecycling and/or
https://www.plastics.org.nz/environment/recycling-disposal/eps-recycling

Glen Dimplex Australia Pty Ltd
8 Lakeview Drive
Scoresby VIC 3179
Phone: 1300 556 816
Email: seasonal.support@glendimplex.com.au
Web: www.morphyrichards.com.au

© Glen Dimplex Australia. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex Australia.

References

• Home - Expanded Polystyrene Australia
• Morphy Richards Australia (@morphyrichardsau) • Instagram photos and videos
• Homepage | Morphy Richards
• EPS Recycling - Green Business HQ
• EPS Recycling | Plastics New Zealand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>