Benjara BM123639 Transitional Style Computer Desk Instruction Manual
- June 17, 2024
- Benjara
Table of Contents
Benjara BM123639 Transitional Style Computer Desk
Specifications
- Assembly Rating: 4 out of 5
- Recommended Number of People for Assembly: 2
- Material: Wood, metal, glass
- Colour: Varies
- Dimensions: Varies
Product Usage Instructions
Pre-Assembly Preparation
- Teamwork: Always have at least two people to help with transporting and assembling the product to avoid potential injury and/or damage.
- Suitable Location: Assemble near the area of the intended location.
- Sufficient Space: Ensure you have enough space to move around during assembly.
- Avoid Scratches: Use cardboard, blankets, or a carpeted area while assembling furniture to prevent scratches and damages.
- Flat Surface: Ensure the furniture rests on a flat and level surface with each leg evenly touching the floor.
Assembly Steps
-
1. **Step 1:** Do not fully tighten all bolts until assembly is complete. This will help all parts to assemble properly. - Step 2: Align the leveller (#1) to the bottom hole of the side panel (#3). Secure by using bolt (#A) with washer (#G).
Note: Refer to the provided diagrams and part numbers to ensure correct assembly.
Post-Assembly
- Final Check: Ensure the furniture rests on an even and flat surface. If the product wobbles or feels loose, double-check all bolts and/or screws are properly tightened and secured.
- Storage: Retain the instruction manual and any order-related information for future reference.
- Handling: Always lift the product when transporting or adjusting the placement to prevent damage.
FAQ
- Q: How long does it take to assemble the product?
- A: The assembly time may vary based on experience, but typically it takes around 1-2 hours with two people working together efficiently.
- Q: Can I assemble the product alone?
- A: While it is recommended to have two people for assembly, experienced individuals may be able to assemble it alone with caution.
TOOLS REQUIRED
2 – People Recommended
ASSEMBLY RATING
The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
PRE ASSEMBLY INTRODUCTION
We understand building ready-to-assemble furniture can be a challenging experience for some. To help avoid confusion, we have provided some helpful tips that may speed up the process.
Teamwork
ALWAYS have at least two people to help with transporting and assembling the
product to avoid potential injury and/or damage.
Suitable Location
Assembling near the area of the intended location is highly recommended.
Sufficient Space
Make sure you have enough space to move around during the assembly.
Avoid Scratches
Use cardboard, blankets or a carpeted area while assembling furniture to
prevent scratches and damages.
Flat Surface
Make sure the furniture rests on a flat and level surface with each leg evenly
touching the floor.
ASSEMBLY AND CARE ADVICE
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE.
- Position each part correctly and insert screws or bolts into their respective holes.
- Use the appropriate hand tools or power tools for assembly. Select steps, such as tightening screws and/or bolts, may require hand tools to avoid causing damage during assembly.
- Turn clockwise to tighten and only tighten when the step is completed or when instructed to do so.
- Save the instructions and store any supplied tools for later maintenance.
- After two weeks, check and tighten any loose hardware and repeat every six months thereafter.
IT IS THE USER’S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE HARDWARE MAY LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY.
COMPUTER DESK WITH WOOD BOARD KEYBOARD
PARTS
HARDWARE
ASSEMBLY INSTRUCTIONS
ASSEMBLY Do not fully tighten all bolts until assembly is complete. This will help all parts to assemble properly.
- Part #3 x2pcs Hardware #1x2pcs
- Align the leveller (#1) to the bottom hole of the side panel (#3).
- Part 2x2pcs
- Hardware A x6pcs
- Hardware G x6pcs
- Hardware J x1 pc
Align arc panel (#2) to side panel (#3), then secure by using bolt (#A) with washer (#G).
- Part 1 x1pc
- Hardware 1c2pcs
Align leveller (#1) to the bottom hole of the back panel (#1 ).
- Part 7 x1pc
- Hardware Bx4pcs
- Hardware Dx2pcs
- Hardware G x2pcs
- Hardware Jx1 pc
Align back panel (#1 ), and top cross bar(#?) to side panel (#3) and arc panel (#2), then secure by using bolt (#A, #D) with washer (#G).
- Part 4x1pc
- Part 5x1pc
- Hardware C x4pcs
- Hardware Jx1 pc
Align the frame for the keyboard (#4, #5) to the back panel (#1) and top crossbar (#7), then secure by using bolts (#C) as shown in the diagram.
- Part 9 x1pc
- Part 10 x1pc
- Hardware E x4pcs
Align slides (#9, #10) to the frame for the keyboard (#4, #5), then secure by using bolts (#E).
- Part 8 x1pc
- Hardware F x4pcs
Align the wood shelf (#8) to the frame for the keyboard (#9, #10), then secure by using screws (#F)
- Part 6 x1pc
- Hardware H x6pcs
Align the suction cup (#H) to the top of the back panel (#1) and top crossbar (#7), then put the table-top glass (#6) on the suction cups (#H) as shown in the diagram.
ASSEMBLY COMPLETED
Keep this handy!
Please retain this instruction manual and any order-related information for
future reference.
Lift, don’t drag!
To avoid damage to a product please always LIFT the product when transporting
or adjusting the placement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>