ZMG Solar Powered Water Fountain with LED Lights Instruction Manual

June 17, 2024
ZMG

Fountain
Assembly instructionsZMG Solar Powered Water Fountain with LED
Lights Powered Water Fountain
with LED Lights

Solar Powered Water Fountain with LED Lights

Please refer to parts letters when assembling.
If you need some more installation videos or warranty information & return policy, please Scan QR cord

ZMG Solar Powered Water Fountain with LED Lights - QR
Codehttps://gift.ferrisland.com/thank-you- card

Please read the operating & installation instructions carefully before installing ,If in doubt consult a qualified electrician.
WARNING: All water features and containers of water can create a 0hazard for children and vulnerable adults. Please do not leave a container of water in any area where young children can explore.
Children should not be left unattended around water.
NOTE: The transformer for the pump and LED light should never be submerged or stood in water.
If placed outdoors the socket outlet must be in a suitably sized waterproof enclosure to IP66 standard.
Always use with a Residual Current Device (RCD) not exceeding 30mAinstalled in the mains supply circuit.

SAFETY INSTRUCTIONS:

ALWAYS DISCONNECTALLAPPLIANCES IN THE POND FROM THE ELECTRICITY SUPPLY BEFORE PUTTING YOUR HANDS IN THE WATER OR WHILST EQUIPMENT IS BEING INSTALLED, REPAIRED, MAINTAINED OR HANDLED.

  • Do not allow the pump to run dry. Operate pump completely submerged for proper cooling
  • Keep cable clear of areas where it may become snagged, damaged or creates a tripping hazard
  • Do not lift the pump up by the supply cable. The supply cable of the pump cannot be replaced as itis permanently connected and sealed in the motor body. If the cord is damaged, the pump must be discarded.
  • Do not use the pump when water is above 30-C or when water is frozen. Do not use to pump flammable liquids.
  • Do not lift or move the water basin to relocate the fountain when it’s filled with water. Switch off the power and empty the water basin before lifting or relocating.
  • The pump on your fountain has no user-serviceable parts. Only a qualified service engineer should service the pump.
  • Only the pump, LED cables and the electrical cord directly connecting them are to come in contact with water. Under no circumstances should the other parts come into contact with water.
  • Do not plug-in or use this product if any part of it appears to be damaged or operates abnormally.
  • Do not open the sealed pump housing or adaptor as this may resultin electrical shock.

Assembly Instructions:

DO NOT CONNECT TO ELECTRICAL SUPPLY & SWITCH ON UNTILALL STEPS HAVE BEEN COMPLETED

  1. Carefully unpack and place the base in an upright position.
  2. Reach inside the water reservoir, gently pull out the tubing, water pipe and internal cables.
  3. Connect the tubing of the water pipe to the pump outlet as shown and then place pump back into the reservoir .
  4. Connect the two ends of the LED wires together and securely screw over the plastic collars.
  5. Ensure the mains lead extends out through the opening
  6. Ensure all connections are secure.
  7. Carefully fill the feature with sufficient water – ensure the pump is fully submerged.
  8. Connect the pump and LED adaptor to the mains power outlet.
  9. Pump Flow: The pump flow can be adjusted by adjusting the flow  control regulator. Its recommended to start with the flow regulator fully open and then adjust it down if required
  10. Switch on

ZMG Solar Powered Water Fountain with LED Lights - Assembley
1

Maintenance & Care:

(To be completed by a technically competent person) ZMG Solar Powered Water
Fountain with LED Lights - Assembley 2

  • Always disconnect from the mains power before the pump is checked.
    Check that the water resevoir has sufficient water to cover the pump at all times.

  • The pump must always be fully submerged in water (even when not in use) and never be permitted to run dry as this could cause permanent damage.
    Also, without sufficient water, it will also cause noise.

  • Do not allow the pump or water feature to freeze.

  • Regularly change the water and clean the water feature. Distilled water is best.

  • The outside of the water feature can be cleaned using a soft cloth and clean water. The resevoir can be cleaned with a soft brush. Avoid the use of detergents as this will cause the water to foam.

  • Excessive weight or pressure on any of the fountain sections may cause it to fail. Keep children, pets or adults from sitting, leaning or climbing on this product.

  • This pump must not be used in or on anything other than the water feature it is supplied with.

  • The pump supply cord cannot be replaced. If the cord is damaged the appliance must be discarded

Troubleshooting:

If your FOUNTAIN PUMP fails to operate please check the following:
– Is the pump connected to the power and is it switched on.
– Check the water level in the fountain. Running the pump without sufficient water can damage the pump. Check the resevoir is at least % full of water.
Check the pump outlet nozzle and the water tube for dirt and debris. Clean if necessary.
Make sure the pump is connected to the water tube tightly. Check the fountain tubing for kinks and obstructions.
– The pump may be “air locked”. Plug and unplug the pump several times to clear any air that may have been trapped.
– If the water does not flow out of the fountain, it may be caused by kinked or loose water tubes, make sure the water tubes are connected securely Design may be subject to change
This product must not be disposed of with domestic waste.
The product must be disposed of at an authorised local collection place for recycling of electrical and electronic devices in pursuant to the European Directive 2002/96/EC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals