DOWINX LS 6688 Series Office Charger Instructions
- June 14, 2024
- DOWINX
Table of Contents
DOWINX LS 6688 Series Office Charger Instructions
SAFETY PRECAUTIONS
BEFORE USE
-
This manual is intended to describe the items that you should be aware of when using the product in order to prevent harm to you and other people and damage to property. Please be sure to observe it for safe use.
-
Please read this manual carefully before use to ensure correct and safe use. Also, please read the quality label attached to the product.
-
The contents of this manual and precautions for use describe precautions to prevent incorrect usage and accidents. Please keep it in a safe place and read it when necessary.
-
When renting or transferring the product to a third party, be same to attach this manual and fully explain the handling method.
-
The warranty period Is one year after delivery. If a failure occurs due to our responsibility within the above warranty period, we will replace or repair it with a replacement product free of charge. Please do not hesitate to contact the after-sales service department: ~ Dowinx@vip.126.com
SAFETY PRECAUTIONS
The precautions written here are to prevent harm or damage to you or others.
All of these are important contents for safe use, so be sure to observe them.
- Do not disassemble or lubricate the gas cylinder. It may explode and cause Injury.
- Please do not incinerate. The high pressure gas in the gas cylinder may explode or emit toxic gas.
- Do not put your hand In the gap between the moving parts. You may get Injured.
- Do not operate the up/ down adjustment lever on the seat surface while the seat is vacant. The seat and back may rise sharply and cause injury.
- Do not use the product as It is found. The main body may break and you may get injured.
- Do not use on slippery floors. You may fall and get injured.
- As It Is an assembly type, tighten the screws firmly to assemble. Also, If any rattling occurs due to loosening of bolts or screws during use, be sure to retighten. If you use it with the bolts and screws loose, the main body may break and you may be injured.
- Please do not let the Infant sit alone. You may fall and get injured.
- Please do not modify.
PRECAUTIONS FOR USE
- This product Is for l111door or indoor use. Outdoor use or getting wet may cause malfunction, rust or discoloration.
- Avoid using the product in a place exposed to direct sunlight or heat such as a stove, or in a place with significant humidity or dryness.
- Tighten the bolts and screws regularly every two-month.
- Tap the cloth part of the seat with your hands or vacuum the cloth to remove dust. Otherwise, wipe off the dirt with a dry cloth or a lightly moistened cloth. (Wipe off the water from the steel part well .) Do not use thinn.er, benzine, cleanser, etc.
PARTS CHECKING
ASSEMBLY INSTRUCTION
Note: Method of Screwing
If you tighten the screws in the beginning, the one of screw holes will not be aligned and you will not be able to assemble. It also will cause overall distortion.
Installation of base
• Insert Base-2 into Base-1 as shown.
- Base 1: The core of the base
- The feet of the base
Installation of casters, cylinder and cover
- Turn the base over and insert the casters firmly as far as it will go.
- Insert the gas cylinder and cover into the base as shown.
- To prevent the casters from coming off, it is a bit difficult to insert.
- The cylinder is coated with lubricating oil. Don’t make your hands, clothes, or floor dirty.
Installation of tilt mechanism and guide rail
Installation of footrest
Attach the cushion to the base
- First, attach the base to the gas cylinder.
Then attach the gas cylinder to the tilt mechanism.
Please check if you inserted it vertically. - If inserted at an angle, the lift function may be unusable.
Installation of reclining mechanism
Installation of headrest and lumbar support
Install the backrest on the cushion
Installation of side covers
-
Attach the reclining mechanism cover to the metal mechanism. Install the two bottom covers first, then the top.
-
Make sure that the holes are aligned, and then tighten the screws pressing the side cover so that it won’t slip. If installed directly, the screws may not fit in the holes.
Installation of armrests
FEATURES
Seat height adjustment function
The height of the seat can be adjusted with the seat lift lever located in the center of the right land side of the seat. Adjust according to your height and ask height.
When raising the seat, lift your hips and pull up the lever lightly, and when
you reach the desired height, release your hand from
the lever.
When lowering the seat, sit deeply in the center of the seat, pull up the lever lightly, and release the lever when it is lowered to the desired height.
Locking strength adjustment grip
With the locking strength adjustment grip, you can adjust the locking strength to your preferences.
Turn the grip clockwise for stronger movement.
Turn the grip counterclockwise to weaken the movement.
Dowinx Official Account
Communicate new products and special
offershttps://dowinx.com/sns/allhttps://qrco.de/bcQbe2https://qrco.de/bcQbeOhttps://twitter.com/DowinxJP?s=09
Please contact our customer support for any questions regarding the
installation, use, etc.
Dowinx@vip.126.eom
2022 Dowinx components, Inc. All rights reserved.
Dowinx and the language logo are registered trademarks in the United States
and /or other countries. The appearance patent of I.S -6689 J has been
registered in the United states. Europe and Japan. Product may vary slightly
from those pictured.