i18B Automatic Scrubber

Product Information

Specifications

• Model: i18B/i18C
• Type: Automatic Scrubber
• Manufacturer: ICE Cobotics (GuangDdong) Company Limited
• Location: XiangShi Road LiaoBu DongGuan GuangDong China
• Contact: Tel: 0769 – 81869000, Fax:0769 – 81863000

Product Usage Instructions

Safety Precautions (For i18B)

This machine is designed for commercial use to scrub hard floors
in indoor environments. Follow these safety precautions:

1. Only operate the machine if trained and authorized.

2. Read and understand the operator’s manual before use.

3. Avoid operating in flammable or explosive areas.

4. Ensure the machine is in proper operating condition before
   use.

5. Avoid outdoor operation.

Safety Precautions (For i18C)

Before operating the machine, carefully read and understand the
manual. Follow these safety precautions:

1. Ground the machine while in use to protect against electric
   shock.

2. Ensure that the machine is properly grounded with an
   equipment-grounding conductor and plug.

3. Do not remove the ground pin under any circumstances.

How to Order Parts

1. Use only ICE Cobotics Company supplied or equivalent
   parts.

2. Identify the machine model and serial number from the data
   label.

3. Order parts online, by phone, by fax, or by mail.

4. Provide necessary information like part number, quantity, name,
   company name, customer ID, billing and shipping address, phone
   number, and purchase order number.

Protecting the Environment

Dispose of packaging materials, old machine components,
batteries, hazardous fluids, etc., in an environmentally safe way
according to local waste disposal regulations. Remember to recycle
whenever possible.

Contact Information

If you have any questions or need further assistance, you can
contact ICE Cobotics (GuangDdong) Company Limited at the provided
telephone and fax numbers.

Note

Specifications and parts are subject to change without
notice.

FAQ

Q: Can I use the scrubber outdoors?

A: No, the scrubber is designed exclusively for indoor use on
hard floors.

Q: How should I dispose of old machine components?

A: Dispose of old machine components in an environmentally safe
way according to local waste disposal regulations. Remember to
recycle whenever possible.

www.ice4usa.com

OPERATOR & Parts Manual

i18B i18C

Automatic Scrubber

8019009 REV.07(06-2023)

OPERATOR MANUAL
READ OPERATOR MANUAL CAREFULLY!
IMPORTANT: To ensure full warranty protection, please fill out & return your warranty card.
Please fill out at time of installation for future reference. Model No. Serial No. Machine Options Sales Rep. Sales Rep. Phone No. Customer ID Number Installation Date
HOW TO ORDER PARTS Only use ICE Cobotics Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail. 1. Identify the machine model. 2. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list. 4. Identify the part number and quantity.
Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.
Always remember to recycle.

ICE Cobotics (GuangDdong) Company Limited XiangShi Road LiaoBu DongGuan GuangDong China Tel: 0769 – 81869000 Fax:0769 – 81863000

Specifications and parts are subject to change without notice.

2

i18B/i18C

OPERATOR MANUAL
TABLE OF CONTENTS
SAFETY PRECAUTIONS…………………………………………………………………………………………4 MACHINE COMPONENTS………………………………………………………………………………………6 MACHINE SETUP & INSTALLATION…………………………………………………………………………7 MACHINE OPERATION…………………………………………………………………………………….8 WHILE OPERATING MACHINE………………………………………………………………………………8 TANK DRAINING…………………………………………………………………………………………………..8 PREVENTATIVE MAINTENANCE…………………………………………………………………………..10 BASIC TROUBLESHOOTING………………………………………………………………………………..12 TECHNICAL SPECIFICATION…………………………………………………………………………13 PARTS LIST……………………………………………………………………………………14-32 WEAR & TEAR PARTS LIST…………………………………………………………………….33 WIRING DIAGRAM ………………………………………………………………………………34-35

i18B/i18C

3

OPERATOR MANUAL

SAFETY PRECAUTIONS(FOR i18B)
This machine is intended for commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use. Only use recommended accessories.

WARNING:Batteries may emit
hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open
flames away! Keep battery compartment open when charging(except maintenance-
free batteries).

All operators shall read, understand and exercise the following safety precautions:
1. Do not operate machine: – Unless trained and authorized. – Unless you have read and understand the operators manual. – In flammable or explosive areas. – If not in proper operating condition. – In outdoors areas.

WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks.
WARNING: Flammable materials or reactive metals can cause explosion or fire. Do not pick up.

2. Before starting machine: – Make sure all safety devices are in place and operate properly.

3. When using machine: – Go slow on inclines and slippery surfaces. – Follow all safety guidelines. – Report and fix any damage to machine prior to operating it. – Never allow children to play on or around the machine. – Do not operate on inclines that exceed 2% (3°).

4. Before leaving or servicing machine: – Stop on level surface. – Turn off machine.

5. When servicing machine: – Read operators manual thoroughly prior to operating or servicing this machine. – Use manufacturer supplied or approved replacement parts. – Secure machine with wheel blocks prior to jacking the machine up. – Use approved jack or hoist to safely elevate the machine. – Disconnect batteries prior to working on machine. – Wear gloves when handling batteries or battery cables. – Avoid any contact with battery acid. – Avoid moving parts. Do not wear loose fitting clothing while servicing machine.
4

i18B/i18C

OPERATOR MANUAL
SAFETY PRECAUTIONS(FOR i18C)
WARNING:Carefully read and understand this manual before operating this machine.This machine must be grounded!
This scrubbing machine shall be grounded while in use to protect the operator from electric shock.Grounding provides a path of least resistance for electric current. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not remove the ground pin under any circumstances.
This machine is for use on a nominal 110-volt circuit and has a grounding plug that resembles the plug illustrated in Figure. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine.

This machine is intended for commercial use. It is constructed for use in an indoor

environment and is nor intended for any other use. Use only recommended accessories.

1. Do not operate machine:

­ Unless trained and authorized.

­ Unless you have read and

­ In flammable or explosive areas.

understood the operator’s manual.

­ With a damaged cord or plug

­ With the use of extension cords.

­ If not in proper operating condition.

­ In outdoor areas and standing water.

2. Before operating machine: ­ Make sure all safety devices are in place and operating properly.

3. When using machine: ­ Do not run machine over cord. ­ Do not pull cord around
sharp edges or corners. ­ Do not handle plug with wet hands. ­ Report machine damage or fault
operation immediately.
4. Before leaving or servicing machine: ­ Turn off machine.
5. When servicing machine: ­ Unplug cord from outlet.

­ Do not pull machine by cord or plug. ­ Do not unplug by pulling on the cord. ­ Do not stretch cord. ­ Keep cord away from heated surfaces.
­ Unplug cord from outlet.
­ Use manufacturer supplied or approved replacement parts.

WARNING:To avoid electrical shock,please replace the power cord immediately if any damage is being detected. The replacement must be performed only by an authorized person or by our customer service center.

WARNING:Flammable materials can cause explosion or fire. Do not use flammable materials in tanks or pick them up.

i18B/i18C

5

OPERATOR MANUAL MACHINE COMPONENTS

9 22*
20 23 21 i18B

9 8
20 23 21 i18C

11

3

13

4

5

25

16

17

7

14 15

24* 24** 18 19

12

1. Brush cover 4. Recovery tank 7. Squeegee 10. Adjusting handle 13. Squeegee lifting handle 16. Brush plunger 19. Clear tube 22*. Battey monitor 24**. Power cord
6

10 1 2

6

11

2. Brush 5. Solution tank 8. Control box 11. Water filter 14. Power cord hook 17. Plug of water filling port 20. Switch for brush motor 23. Circuit breaker 25. Adjustable wheel

3. Cover tank 6. 8″ wheels 9. Trigger 12. Ball valve 15. Brush/pad driving hub 18. Knob 21. Switch for vacuum motor 24*. Charger power cord

• : only for i18B **:only for i18C
  i18B/i18C

OPERATOR MANUAL
MACHINE SET UP & INSTALLATION
UNPACK MACHINE:
Be sure and check packing carton for any damage. Immediately report any damage to carrier. Be careful not to let machine vibrate while carrying, Check contents of package to ensure that the following items are included: Machine, squeegee assembly, brush/pad driver, charger cord.
MACHINE SET UP & PRE-OPERATION CHECKS:

1. Sweep the outside of the machine. 2) Check battery meter to make sure batteries are fully charged (see battery charging, only for i18B ). 3) Check that squeegee and brush / pad is properly installed. 4)Theforwardspeed of machine can be controlled by turning the handle(10). Turn the handle
   clockwise to speed up machine. or turn the handle anticlockwise to slow down machine. 5)Makesuretheworkingsurfacecan support the machine weight, thegradient of the floor can’t
   exceed the limit that machine allowed(2%).
   INSTALLING PAD DRIVER OR BRUSH:
2. Turn off machine. 2)Tiltthemachine backwards,line upthe driving hub with the hole of brush or pad driver, make
   sure the three blocks are fitted into the three slots of the drive hub. *If a pad driver is being used, the appropriate pad should be attached to the pad driver first. 3)Pushtheplungerwhichon the brush cover to prevent the driving hub from rotating,then spin the brush/pad clockwise with your another hand till the clip clamp the block on the brush/pad.
   INSTALLING THE SQUEEGEE:
   1)Loosen the twoknobs(18) on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the machine.) 2) Tighten the knobs securely.
   FILLING THE SOLUTION TANK:
3. The fill port is located at the rear of machine,pull the plug out of the hole. 2) Fill solution tank with water. (use a hose which link to a water faucet,water temperature
   should not exceed 50° C) The clear tube(19) in the back right of the machine has gallon markers to help determine the water level in the solution tank(5). *Depending on the dirty level of the ground, add the proper amount of detergent into the solution tank.

WARNING:Do not put any flammable materials into solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals.

i18B/i18C

7

OPERATOR MANUAL
MACHINE OPERATION

WARNING:Do not operate machine unless you have read and understand this manual.

1. Lower squeegee assembly to the floor by spin the squeegee lifting handle(13). 2) Turn brush motor switch(20) to “on” position. 3) Turn vacuum motor switch(21) to “on” position. 4) Rotate the ball valve(12) handle to vertical position. Solution will not begin to flow until the
   operating triggers (9) are pulled. 5)To begins crubbing,pull on the blue operating trigger(9), when this triggers is pulled, the pad driver will begin to spin and the solution will begin to flow. 6) Begin scrubbing by moving the machine forward. 7) Adjust solution flow by adjusting the position of ball valve knob.
   WARNING:Do not keep the machine in the same position with the pad / brush spinning, or you might damage the floor.
   WHILE OPERATING MACHINE
   1)Occasionally open the cover tank(3) to see if there is any foam build-up.If excessive foam is found, add defoamer to the recovery tank.
   WARNING:Foam must not enter the float shut-off screen, or damage can occur to the vacuum motor. Foam will not activate the machine’s float shut-off device.
   2)Occasionally view the clear tube at the back left of the machineto check thea mount of cleaning solutionthatis left in themachine. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth.
   WARNING:Do not use your fingers to wipe or remove debris from the blades, as injury may occur.
   When the solution tank runs empty, turn off the brush switch and ball valve of solution tank. Keep the squeegee down and continue to vacuum until all the dirty water is picked up.
   TANK DRAINING
2. Turn the switches on the control panel to “off ” position. 2) Raise the squeegee, transport machine to approved area for draining tank(s).
   WARNING:Any time scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned.

WARNING:If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shut-off mechanism and cause damage to the vacuum motor.

8

i18B/i18C

OPERATOR MANUAL
DRAINING THE RECOVERY (DIRTY) TANK

1. Remove the drain hose from the holder, and place the drain hose over the floor drain. Twist off the drain hose plug to begin the draining process. 2) Clean the recovery tank after every use. Use a fresh water hose to rinse out the recovery tank. Be careful not to spray water into the float shut-off mechanism.
   WARNING:If you are storing the machine for any period of time, keep the cover tank open so the tank can dry completely and smell fresh.
   DRAINING THE SOLUTION (CLEAN) TANK
   WARNING:Any time scrubbing operation is completed, the solution tank should be drained and cleaned.
2. Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This will allow the solution to flow freely into a bucket or floor drain. 2) Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines. 3) Once tank is rinsed, flushed and drained, reconnect the clear tube to the hose barb. Be sure the tube is pushed all the way up on the hose barb. 4) Screw off the cover of the water filter(11) to compeletly exhaust the tank and check the filter screen, clean it up if necessary. 5) Screw up the cover of the water filter(11),bu sure to install the screen and the “O” ring in the correct position.

filter screen
“O” ring
filter cover
BATTERY CHARGING (ONLY FOR i18B)
Each machine was equipped with on-board charger and batteries, please use oringinal parts only.

WARNNING: Fire or explosion hazard. Batteries may emit hydrogen gas. Keep sparks and open flame away. Keep battery compartment open when charging.
NOTE: Use only approved chargers with the following specifications: – Automatic shut off circuit. – Deep cycle charging. – Output current of 8-15 Amps. – Output voltage of 24 volts.

i18B/i18C

9

OPERATOR MANUAL

Battery Indicator Description:

Green lights on: full power. Yellow lights on, green lights off : medium power. Red light on, other lights off: 20% power, the maichine should be stopped and the batteries should be recharged. Red light flash: the batteries have already been discharged deeply.

NOTE: Frequently deep discharging will reduce the life of the batteries, charge the batteries Red Yellow 2 Yellow 1 Green 2 Green 1 when the red light is on.

1. Place the machine in a well ventilated area. 2) Turn the machine off. 3) If charging wet (lead acid) batteries, check the fluid level before charging. 4) Connect the charger’s AC power supply cord to a properly grounded receptacle.
2. The charger will automatically begin to charge and will automatically shut off once the
   batteries are fully charged. 6) Upon completion of charging, disconnect the AC power supply cord.
   NOTE: The charging status can be seen through the lights behind the transparent panel: Yellow light on: Normal charging Green light flash: 80% charged Green light on: Fully charged, batteries ready for use. Yellow lights flash: No batteries or incorrect wiring.

PREVENTATIVE MAINTENANCE
WARNNING: Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected!

WARNNING: Repairs are to be completed by authorized service centers only. Any repairs completed by unauthorized persons will avoid the warranty.
DAILY MAINTENANCE

1. Remove pad driver / brush and clean with approved cleaner. 2) Drain recovery and solution tanks completely and rinse out with clean water. Visually check
   the recovery tank for debris and clean out as necessary. 3) Raise squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the
   squeegee in the up position. 4) Remove the float shut-off assembly and rinse it out with clean water. 5) Clean machine with an approved cleaner and a damp towel. Don’t spray water to clean the
   outside of machine to avoid damage to motor and wiring. 6) Unplug vacuum motor from power source and hose cuff & remove the drain hose from the
   holder prior to removing the recovery tank when performing maintenance. 7) Check the condition of the squeegee blade wiping edge, rotate blade or replace it if worn.

10

i18B/i18C

OPERATOR MANUAL
MONTHLY MAINTENANCE

1. Clean the battery tops to prevent corrosion (only for i18B). 2) Check for loose battery cable connections (only for i18B). 3) Inspect and clean the recovery tank cover seal. Replace it if damaged. 4) Lubricate all grease points and pivot points with silicon spay and approved grease. 5) Check the machine for loose nuts and bolts. 6) Check the machine for leaks.
   MOTOR MAINTENANCE
2. Contact your local ICE Distributor for any motor maintenance. 2) Check the motor brushes every 250 hours, Replace the brushes when they are worn to a length of 10mm or less.
   BATTERY MAINTENANCE (ONLY FOR i18B)
   WARNNING: Batteries may emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times.
   WARNNING: Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times.
   Note: For the best machine performance, keep batteries charged at all times.Do not let them sit in a discharged condition. 1) Always follow the battery charging direction as outlined in the BATTERY CHARGING section of this manual.
3. Keep battery tops and terminals free from corrosion. A strong solutin of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS. 3) Use a wire brush with the baking soda solution to properly clean the battery posts and connections. 4) Check battery connections for wear and loose terminals. Replace them if necessary.
   MACHINE STORAGE
4. Always store the machine indoors and in its upright position. 2) Always store the machine in a dry area. 3) Always take off the pad driver / brush before storage. 4) Always store the machine with the squeegee assembly raised off the floor. 5) If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage(include the filter). Any damage caused by freezing temperatures will not be covered by the warranty. 6) Drain the recovery tank and keep the cover tank open so that it can “breathe” during storage. 7) Drain the solution tank of all fluid.

i18B/i18C

11

OPERATOR MANUAL

BASIC TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

No Power

The wiring not connected correctly or bad wiring
Bad brush motor Carbon brushes worn out

Check the wiring or contact ICE Distributor
Contact ICE Distributor Contact ICE Distributor

Vacuum motor does not run

The wiring not connected correctly or bad wiring
Bad vacuum motor Carbon brushes worn out

Check the wiring or contact ICE Distributor
Contact ICE Distributor Contact ICE Distributor

Bad ball valve

Contact ICE Distributor

Little or no Bad solution valve

Contact ICE Distributor

solution flow Ball valve position in need of When ball valve is in horizontal position,the amount

adjustment

of solution flow is maximum.

Squeegee clogged Squeegee blades worn

Clean debris off squeegee with a damp towel Install new squeegee blades

Squeegee not mounted correctly

Confirm that the squeegee assembly is securely fastened to the machine and not loose fitting.

Vacuum hoses have a hole or Check hose connections and make sure they are

are loose

firm. Replace hose if damaged.

Poor water pick up

Vacuum hose may be cloggedCheck hose for debris and remove any clog.

Drain hose stopper is loose Tighten drain plug.

Vacuum motor is loose

Tighten vac motor mounting screws. Do not over tighten or damage will occur.

short runtime*

cover tank is loose

Confirm the cover tank is securely in its place.

Recovery tank is full

Drain recovery tank

Float shut off is clogged

Remove float shut off from inside recovery tank and remove any debris

Low battery charge

Fully recharge batteries

Defective batteries

Replace batteries

Batteries need maintenance See BATTERY MAINTENANCE

Faulty battery charger

Repair or replace battery charger

• ONLY FOR i18B 12

i18B/i18C

OPERATOR MANUAL

TECHNICAL SPECIFICATION

ITEM

i18B

i18C

Working Width Squeegee Width Productivity rate
Brush Dia. Brush Speed Max Pad Pressure Voltage Brush Motor Vacuum Motor Batteries Solution Tank Capacity Recovery Tank Capacity Machine Weight (w/o batteries) Batteries Weight Machine Length Machine Height Machine Width Power cord Length Charger cord length Max Gradient Type of Drive Noise Level
WATER LIFT – AIR FLOW

18in / 450mm

30in / 762mm

16145 ft2h / 1500m2h

12915 ft2h / 1200m2h

18in / 450mm

180rpm

55lbs / 25kg

24VDC

120VAC

0.75hp / 550W

0.7hp / 500W

2-12V, 85AH @20hr

N/A

9.25Gal / 35L

10.57Gal / 40L

138lbs / 62.5kg

110lbs / 50kg

N/A

45.87in / 1165mm

40.35 in / 1025mm

20.5in / 520mm

N/A

82ft / 25m

8.2ft / 2.5m

8.2ft / 2.5m

2%

Brush assisted

70 dB

45 IN.H2O

i18B/i18C

13

PARTS LIST

RECOVERY TANK GROUP

14

i18B/i18C

PARTS LIST

RECOVERY TANK GROUP

DIA PART NO. NUMBER

DESCRIPTION

8011001 RECOVERY TANK 1
8016001 RECOVERY TANK

2 8011011 DECAL,LEFT 3 4010316 ICE LOGO

8131030 DRAIN HOSE 4
8131031 DRAIN HOSE

5 1962050 HOSE CLAMP 27-51mm

8011006 VACUUM HOSE 6
8011060 VACUUM HOSE

8132006 CARBON BRUSH (FRO i18B)

7 8112008 CARBON BRUSH (FRO i18B)

8011022 CARBON BRUSH (FRO i18C)

8 1113608 SELFLOCKING NUT M6

9 1411612 PLAIN WASHER 6×12×1.6

10 8011007 MUFFLER

8132050 VACUUM MOTOR 24V, KIT (FRO i18B)

11

8112100 VACUUM MOTOR 24V, KIT (FRO i18B)

8011200

VACUUM MOTOR 110V, 500W, KIT (FRO i18C)

12 8112005 GASKET

13 8112006 BOLT

14 1111605 HEX NUT M6

15 1021616 HEX HEAD BOLT M6×16

16 1421618 PLAIN WASHER 6×18×1.6

17 8111300 HINGE ASSEMBLY

18 8011012 DECAL,RIGHT

19 8011009 PLATE

20 1421409 PLAIN WASHER 4×9×0.8,SS

21 1221410 PH SCREW M4×10,SS

22 8111015 FLOAT CAGE

23 8111014 FLITER COUPLING

24 8111001 GASKET

25 1321110 AUTO TAPPING SCREW ST3.5×10

26 1421412 PLAIN WASHER 6×12×1.6

8131003 CAP 27
8131004 CAP

28 8011013 CABLE
Note: NO 14711Supplier change, code update. NO 27The results are optimized and will also fit older machines.

SERIAL NUMBER
60003100364~60003100853 50010100124~50010100713 60003100945~60012103001~ 50010100714~51010101228~
60003100958~60012102302 50010100724~51010101128
60012102343~ 51010101129~ 60003100945~60012102405 50010100713~51010101150 60012102457~ 50010100713~51010101150~
60003100101~60003100364 60003100365~60012103001~ 50010100124~51010101228~
60003100364~60012102611 50010100713~51010101150
60012102612~ 51010101151~

NO. REQ’D
1
1
1 3
1
1
2
1
1
2 2 2 3 5 1 1 1
1
1 3 3 10 10 2 1 2 5 2 1 1 1 1 1
1
1
1

i18B/i18C

15

PARTS LIST

COVER TANK ASSEMBLY

COVER TANK ASSEMBLY

DIA PART NO. NUMBER

DESCRIPTION

1

8012005 COVER TANK

8012001 WARNING LABLE

2

8111022 WARNING LABLE (FOR i18B)

8012003 WARNING LABLE (FOR i18C)

3

8011005 CAP

8012002 GASKET

4

8012002A GASKET

Note: DIA NO 4:Supplier change, code update.

SERIAL NUMBER
50010000124~50010100713 60003000364~60012103001~
51010101150~
60003100471~60012103001~ 50010100557~51010101228~

NO. REQ’D
1 1 1 1 1 1
1

16

i18B/i18C

SOLUTION TANK GROUP

PARTS LIST

i18B/i18C

17

PARTS LIST

SOLUTION TANK GROUP

DIA PART NO. NUMBER

DESCRIPTION

SERIAL NUMBER

1

8013008 DECAL,LEFT

2

8050475

CABLE ASSEMBLY WITH CONNECTOR(BLACK i18B)

8050475-1

CONNECTOR,BATTERY,BLACK ANDERSON 5916G4(i18B)

8013001 SOLUTION TANK

60003000364~60003000853 50010000124~50010000713

3

8017001 SOLUTION TANK

60003100945~60012103001~ 50010100713~51010101228~

8133033

SOLUTION TANK(I18B,I18C REPLACE THE OLD WATER TANK 8013001)

4

8013010 12V BATTERY (FOR i18B)

5

1321110 AUTO TAPPING SCREW ST3.5×10

6

1421409 PLAIN WASHER 4×9×0.8

7

8133002 PLUG

8

8013005 TRANSPARENT HOSE

9

8034012 BRACKET, CASTER

10

8013016 2″ CASTOR

11

1421618 PLAIN WASHER 6×18×1.6

12

1422616 SPRING WASHER 6 SS

13

1021616 HEX HEAD SCREW M6×16,SS

14

1021830 HEX HEAD SCREW M8×30,SS

15

1422821 SPRING WASHER 8

16

1421824 PLAIN WASHER 8×24×2.0

17

8016010 WHEEL SHAFT

18

1421816 PLAIN WASHER 8×16×1.6

19

1021820 HEX HEAD SCREW M8×20,SS

8115200 8″ WHEEL 20
1612607 BALL BEARING, 6004LU

21

1421828 PLAIN WASHER 8×28×3

22

8115203 WHEEL CAP

23

1962032 HOSE CLAMP

24

8013009 DECAL,RIGHT

25

8013002 BACKET

26

1221510 PH SCREW M5×10,SS

27

1421510 PLAIN WASHER 5×10×1,SS

28

8113009 WIRE CLAMP

29

8114751 WIRING BOOT (FOR i18B)

30

8050476

CABLE ASSEMBLY WITH CONNECTOR(RED i18B)

8050476-1

CONNECTOR,BATTERY,RED ANDERSON 5916G7(i18B)

31

8114750 BATTERY CABLE(I18B)

Note: DIA NO 3:The results are optimized and will also fit older machines.

NO. REQ’D
1
1
1
1
1
1
2 1 1 1 1 1 1 3 3 3 1 3 1 1 2 4 2 4 2 2 1 1 1 4 4 4 4
1
1
1

18

i18B/i18C

CONTROL BOX ASSEMBLY (FOR i18B)

PARTS LIST

i18B/i18C

19

PARTS LIST

DIA NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
20

CONTROL CONSOLE GROUP

PART NUMBER

DESCRIPTION

8014062 1421512 1211516 1421409 8114707 1113305 8014061 1411309 8014034 1411824 1021820 8114030 8014076 8113104

REAR PANEL PLAIN WASHRE 5×12×1.5 PH SCREW M5×16 PLAIN WASHER 4×9×0.8 RELAY SELFLOCKING NUT M3 SWITCH BRACKET PLAIN WASHER 3×9×0.8 BRCKET PLAIN WASHER 8×24×2 HEX HEAD BOLT M8×20 FIXING BRACKET,CONTROL BOX BATTERY CHARGER 24V HANDLE

6210111 HOSE CLAMP

6210120
1221416 8014010 8014008 8034010 8114511 1421618 1121605 1421828 1021830 1221512 8114005 8112030 8014038 8014036 8014044 1221516 1123608 8114703 1421518 1021512 8034011 8014101 1021630 8014045 8014006 8014043 8014041 1221616

HOSE CLAMP
PH SCREW M4×16 SS SQUEEGEE LIFTING HANDLE CONTROL BOX SQUEEGEE LIFTING ROPE JOINT BEARING SQ6 PLAIN WASHER 6×18×1.6,SS HEX NUT M6 PLAIN WASHER 8×28×3 HEX HEAD BOLT M8×30 PH SCREW M5×12,SS PIPE COUPLING CHARGER CORD (FOR US) GASKET PANEL PLATE PH SCREW M5×16 SS SELFLOCKING NUT M6,SS OVERLOAD PROTECTOR 35A PLAIN WASHER 5×18×2 HEX HEAD BOLT M5×12,SS BAFFLE LIFTING ROPE SPACER HEX HEAD BOLT M5×12,SS TRANSPARENT PLATE WATERPROOF SWITCH 250V 16A WIRE BUFFER
WIRE CLAMP PH SCREW M6×16,SS

SERIAL NUMBER
60003000364~60003000534 50010000430~50010100924 60003101551~60012103001~ 50010100943~51010101228~

NO. REQ’D
1 9 5 13 1 8 1 8 1 6 6 1 1 1
1
1
2 1 1 1 1 4 2 2 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1

i18B/i18C

PARTS LIST

CONTROL CONSOLE GROUP

DIA PART NO. NUMBER

DESCRIPTION

44

2320403 STRAIN RELIEF

45

8014063 BATTERY CAPACITY INDICATOR

46

1221410 PH SCREW M4×10,SS

47

8014067 PANEL DECAL

48

8014069 FRONT PANEL

49

8114101 SHAFT

50

8014004 GASKET

51

1221412 PH SCREW M4×12, SS

52

1432411 SPRING WASHER 4

53

1411409 PLAIN WASHER 4×9×0.8

54

8014022 CONTROL TRIGGER

55

8014033 PLATE

56

1534608 SET SCREW M6×8

57

8014031 HEX BUSHING

58

8014032 SPRING ROD

59

8014035 SPRING

60

1211320 PH SCREW M3×20

61

1434300 WASHER WITH TOOTH 3

62

8114712 MICROSWITCH

63

1113507 SELFLOCKING NUT M5

64

8210421 RELAY 24VDC 30A

65

1123406 SELFLOCKING NUT M4, SS

Note: DIA NO 1519:Supplier change, code update.

SERIAL NUMBER

NO. REQ’D
1 1 15 1 1 1 1 4 2 2 1 1 4 1 1 1 2 2 1 7 1 2

i18B/i18C

21

PARTS LIST

CONTROL BOX ASSEMBLY (FOR i18C)

22

i18B/i18C

PARTS LIST

CONTROL CONSOLE GROUP

DIA PART NO. NUMBER

DESCRIPTION

1

1421409 PLAIN WASHER 4×9×0.8

2

1211516 PH SCREW M5×16

3

1113305 SELFLOCKING NUT M3

4

1021820 HEX HEAD BOLT M8×20

5

1411824 PLAIN WASHER 8×24×2

6

1113507 SELFLOCKING NUT M5

7

8114030 FIXING BRACKET,CONTROL BOX

8

8113104 HANDLE

6210111 HOSE CLAMP 9
6210120 HOSE CLAMP

10

1221416 PH SCREW M4×16 SS

11

8014010 SQUEEGEE LIFTING HANDLE

12

8014008 CONTROL BOX

8014013 SQUEEGEE LIFTING ROPE 13
8034010 SQUEEGEE LIFTING ROPE

14

8114511 JOINT BEARING SQ6

15

1421618 PLAIN WASHER 6×18×1.6,SS

16

1121605 HEX NUT M6

17

1421828 PLAIN WASHER 8×28×3

18

1021830 HEX HEAD BOLT M8×30

19

1221512 PH SCREW M5×12

20

1221516 PH SCREW M5×16 SS

21

8014044 PLATE

22

8114005 PIPE COUPLING

23

8014037 PANEL, BOTTOM

24

8014038 GASKET

25

8014068 OVERLOAD PROTECTOR 10A

26

8014053 POWER CORD

27

1221410 PH SCREW M4×10,SS

28

1123608 SELFLOCKING NUT M6,SS

29

8034011 BAFFLE

30

1421512 PLAIN WASHRE 5×12×1.5

31

1021512 HEX HEAD BOLT M5×12,SS

32

8014101 LIFTING ROPE SPACER

33

1021630 HEX HEAD BOLT M6×30,SS

34

8014006 WATERPROOF SWITCH 250V 16A

35

8014041 WIRE CLAMP

36

8014043 WIRE BUFFER

37

1221614 PH SCREW M6×14

38

1422616 SPRING WASHER 6

39

2320403 STRAIN RELIEF

40

8014007 PANEL DECAL

SERIAL NUMBER
60003000364~60003000534 50010000430~50010100924 60003101551~60012103001~ 50010100943~51010101228~

i18B/i18C

NO. REQ’D
11 4 2 6 6 4 1 1
1
1
2 1 1 1 1 1 4 2 2 2 1 2 1 1 1 1 1 1 15 1 1 8 1 1 1 2 1 1 1 1 1 1
23

PARTS LIST

CONTROL CONSOLE GROUP

DIA PART NO. NUMBER

DESCRIPTION

41

8014005 FRONT PANEL

42

8014004 GASKET

43

8114101 SHAFT

44

1221412 PH SCREW M4×12,SS

45

1411409 PLAIN WASHRE 4×9×0.8

46

1432411 SPRING WASHER 4

47

8014033 PLATE

48

8014022 CONTROL TRIGGER

49

1534608 SET SCREW M6×8

50

8014031 HEX BUSHING

51

8014032 SPRING ROD

52

8014035 SPRING

53

1211325 PH SCREW M3×25

54

1411309 PLAIN WASHER 3×9×0.8

55

8014071 SWITCH

56

8014061 SWITCH BRACKET

57

8014002 REAR PANEL

58

8014034 BRACKET

Note: DIA NO 913:Supplier change, code update.

SERIAL NUMBER

NO. REQ’D
1 1 1 2 2 2 1 1 4 1 1 1 2 4 1 1 1 1

24

i18B/i18C

SCRUB HEAD GROUP

PARTS LIST

23

i18B/i18C

25

PARTS LIST

DIA NO.
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
26

SCRUB HEAD GROUP

PART NUMBER

DESCRIPTION

8015200 MOTOR 24V 550W, KIT (FOR i18B)

8015220 8015020 8015010 1511065 1644220 8015101 1111008

MOTOR 120V 550W, KIT (FOR i18C) ADJUSTING HANDLE BRUSH HANGER HEX SOCKET SCREW M10×65 PIN 12×20 DECAL HEX NUT M10

8015104 BEARING GEC6C

8015105 1439005 8015087

BEARING HOUSING DETENT RING 5 ASSAMBLY BOARD

8015050 BRUSH PLUNGER

1123810 1421816 8115404 8116009

SELFLOCKING NUT M8,SS PLAIN WASHER 8×16×1.6,SS SPACER BUMPING WHEEL

8111023 1221512 1421510 8116002

WARNING DECAL
PH SCREW M5×12 PLAIN WASHER 5×10×1,SS WASHER

8116003 SPRING CLAMP

8116008 9050018 1421828 8015090

BRUSH HUB BRUSH 18″ PLAIN WASHER 8×28×3 SPLASH GUARD

1422821 1023810 1021835 1111215

SPRING WASHER 8
HEX HEAD BOLT 5/16×1″,SS HEX HEAD BOLT M8×35,SS HEX NUT M16

8015108 1011016 1411020 1011625 1421618 1221510 1212410 8015060

SUPPORTER
HEX BOLT M6×16 PLAIN WASHER 10×20×2 HEX HEAD BOLT M6×25 PLAIN WASHER 6×18×1.6,SS SH SCREW M5×10 SH SCREW M4×10 WATER INLET

8015041 MOTOR BRACKET

8015005 1222510 1421518 1422513 1221515 1221616 8015103 1221410 1321213

BRUSH COVER
SH SCREW M5×10 PLAIN WASHER 5×18×2,SS SPRING WASHER 5
PH SCREW M5×15 PH SCREW M6×16 VALVE BRACKET
PH SCREW M4×10,SS AUTO TAPPING SCREW ST4.2×13

SERIAL NUMBER

NO. REQ’D
1 1 1 1 1 2 1 1 1 1 1 1 1 1 3 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 4 4 8 1 2 1 1 1 2 4 5 3 8 1 2 2
i18B/i18C

SCRUB HEAD GROUP

DIA PART NO. NUMBER

DESCRIPTION

48

1646240 COTTER PIN 2×40

49

8015116 NYLON WASHER 12.5×20×1.5

50

8015001 BRACKET

51

1123608 SELFLOCKING NUT M6,SS

52

1511040 HEX SOCKET SCREW M10×40

53

8015007 BUSHING

54

1113012 SELFLOCKING NUT M10

55

8015115 NYLON WASHER 10.5×30×2.5

56

8015121 SPACER 13×10.5×5.5

57

8015002 BRACKET

58

8116004 DETENT RING

59

1656432 KEY 6.35×32

60

8015003 SPACER 25.5×19.5×5

61

8115004 SPRING

SERIAL NUMBER

PARTS LIST
NO. REQ’D
2 4 1 4 2 3 1 2 1 1 1 1 1 1

23

DIA PART NO. NUMBER

DESCRIPTION

1

9050018 BRUSH 18″

2

9040017 PAD DRIVER 17″

3

9000001 BIG MOUTH

SERIAL NUMBER

NO. REQ’D
1 1 1

i18B/i18C

27

PARTS LIST

SQUEEGEE HOLDER ASSEMBLY

28

i18B/i18C

PARTS LIST

SQUEEGEE HOLDER ASSEMBLY

DIA PART NO. NUMBER

DESCRIPTION

1

8037020 BRACKET, SQUEEGEE MNTG

2

1421618 PLAIN WASHER 6×18×1.6

3

1422616 SPRING WASHER 6 SS

4

1021616 HEX HEAD SCREW M6×16,SS

5

1021230 HEX HEAD BOLT M12×30,SS

6

1421132 PLAIN WASHER 12×32×2.0

7

8035001 PLASTIC WASHER 12×30×1.5

8

8115004 SPRING

8115405 SLEEVEE, P/M 9
8115005 SLEEVEE, P/M

10

8037010 BRACKET, SQUEEGEE

11

1123115 SELFLOCKING NUTS M12

12

8115001 SQUEEGEE SUPPORT

13

8037015 PIN 12×70

14

1645324 COTTER PIN

Note: NO 9The results are optimized and will also fit older machines.

SERIAL NUMBER
60003000364 50010000124~50010000518 60003000365~60012103001~ 50010000519~51010101228~

NO. REQ’D
1 3 3 3 2 2 4 1 2
2 1 2 1 1 1

i18B/i18C

29

PARTS LIST

SOLUTION SYSTEM ASSEMBLY

SOLUTION SYSTEM ASSEMBLY

DIA PART NO. NUMBER

DESCRIPTION

1

1962016 HOSE CLAMP

2

8018004 HOSE

8018007 SOLENOID VALVE, 24V (FOR i18B) 3
8018009 SOLENOID VALVE, 110V (FOR i18C)

4

8018003 HOSE

5

8119006 HOSE CLAMP

6

8119200 WATER FILTER

7

8018002 HOSE

8

8013007 JOINT

9

8018006 BALL VALVE

10

8013006 90º JOINT

11

8119101 FILTER BODY

12

1622765 O RING

13

8119104 FILTER SCREEN

14

8119102 FILTER COVER

15

1421409 PLAIN WASHER 4×9×0.8,SS

16

1221412 PH SCREW M4×12, SS

SERIAL NUMBER

NO. REQ’D
2 1 1 1 1 4 1 1 1 1 1 1 1 1 1 2 2

30

i18B/i18C

SQUEEGEE ASSEMBLY

PARTS LIST

i18B/i18C

31

PARTS LIST

SQUEEGEE ASSEMBLY

DIA PART NO. NUMBER

DESCRIPTION

1

1123810 LOCK NUT M8

2

1421824 FLAT WASHER M8× 24×2.0

3

8116009 PROTECTIVE WHEEL

4

1021616 HEX BOLT M6×16

5

8115404 BEARING, JOURNAL

6

1421612 FLAT WASHER M6× 12×1.6

7

8118300 LEFT BRACKET

8

8118400 CASTER, 2 INCH

9

8118600 CLAMP ASSEMBLY, SQUEEGEE

8118022 SQUEEGEE BLADE, REAR, LINATEX 10
8118002 SQUEEGEE BLADE, REAR, PU (OPTION)

11 8118003 STAR KNOB M8

12 8118004 SQUEEGEE HOUSING

13 1021835 HEX BOLT M8×35

14 8118009 RETAINER,SQUEEGEE

15 8118008 SPACER

16 1222515 SCREW M5×15

17 8118010 RETAINER ASSEMBLY

8118021 SQUEEGEE BLADE, FRONT, LINATEX 18
8118001 SQUEEGEE BLADE, FRONT, PU (OPTION)

19 8118610 SHORT CLAMP ASSEBLY

20 1221575 SCREW M5×75

21 8118200 RIGHT BRACKET

22 1121008 HEX NUT M10

23 8118600A CLAMP ASSEMBLY

24 8118624 SHAFT

25 8118623 SPACER

26 1123507 LOCK NUT M5

8011003 VACUUM HOSE 27
8011060 VACUUM HOSE

8118000 SQUEEGEE ASSEMBLY, LINATEX 28
8118000-PU SQUEEGEE ASSEMBLY, PU

Note: DIA NO 27:Supplier change, code update.

32

SERIAL NUMBER

NO. REQ’D
2 4 2 2 2 2 1 2 1 1 1 4 1 2 1 1 6 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1
i18B/i18C

PARTS LIST

DIA PART NO. NUMBER

1

8115200

2

8116009

3

8118022

4

8118021

5

9040017

6

9050018

WEAR & TEAR PARTS LIST

DESCRIPTION
WHEEL, 8 INCH, WITH BEARINGS BUMPER, ROLLER REAR SQUEEGEE BLADE, LINATEX FRONT SQUEEGEE BLADE, LINATEX PAD HOLDER, 17 INCH BRUSH, 18 INCH

SERIAL NUMBER

NO. REQ’D
2 3 1
1 1 1

i18B/i18C

33

WIRING DIAGRAM

WIRING DIAGRAM(i18B)

34

i18B/i18C

WIRING DIAGRAM(i18C)

WIRING DIAGRAM

i18B/i18C

35

CERTIFICATE OF QUALIFIED

MODEL :

SERIAL NO.:

INSPECTOR:

DATE :

ICE Cobotics (GuangDdong) Company Limited

TEL : (+86) 769 8186 9000

FAX : (+86) 769 8186 3000

References

• Intelligent Cleaning Equipment (ICE)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>