Hisense 10000-BTU DOE Portable Air Conditioner Instruction Manual
- June 17, 2024
- Hisense
Table of Contents
Hisense 10000-BTU DOE Portable Air Conditioner Instruction Manual
Keep unit upright at least 2 hours prior to use.
Parts Package
Before beginning, check that all parts are included in the parts package
Non-adhesive foam seal|
---|---
Adhesive foam seal (2)|
Adhesive foam seal (2)|
Coupling|
Flexible exhaust hose|
Window exhaust adapter|
Window-lock bracket(2)|
Outer slider section with vent|
Inner slider section-short|
Inner slider section|
Outer slider section|
– Drain hose clip (Heat pump models)|
Drain hose|
Heat pump models)|
Rivets (4)| ****
Wood screws(4|
Tools needed
Phillips screwdriver|
Pencil|
Scissors|
step 1
Suitable Window
The window installation kit allows you to install the air conditioner in most vertical-sliding windows 18″ to 50″ wide, or horizontal-sliding windows from 18″ to 50″ high.
Panel window| H18″| I
9W6“| J18″| K18″
---|---|---|---|---
18″| | | |
19″-26″| V| V| |
27″-34″| V| | V|
35″-50″| V| | V| V
Panel H (18″)
Panell (9’X”)
Panel K (18″)
Panel J (18″)
step 2
Window Installation
-
Cut the adhesive foam seal to the proper length, and attach it to the window sash and frame.
-
Insert the vent panel assembly, including ex- tension panels, if needed, into the window opening. Extend the extension panels, if used.
If your window length requires more than two panels, after adjusting the length, please secure the panels with rivets,
-
Cut the Non-adhesive foam seal to the window width. Stuff the foam seal between the glass and the window to prevent air and in- sects from getting into the room.
-
Install the Window-lock bracket with wood screws as shown, if you need,
step 3
Connect it together
-
Preparing the exhaust hose assembly: Press the flexible exhaust hose into the coupling and the window exhaust adapter, Both the coupling and window exhaust adapter have integral clips that snap onto the hose.
-
Connect The Hose To The Air Conditioner Slide the coupling into the slot on the back of the air conditioner to lock the hose on the unit.
-
Connect The Hose To The Window Roll the air conditioner to selected location, Attach the window exhaust adapter to the outer slider section (the piece with the large exhaust hole.
To ensure proper ventilation, keep a distance of least 20in (50 CM) between the Portable AC and the window
-
Plug In the Unit
Be sure to use a grounded 3 prong outlet, Do not use an extension cord, Plug in the unit. -
Turn The Unit On
Turn the air conditioner on, and set the desired mode and temperature.
Waterless Design
- Waterless Design doesn’t require routine draining in cooling mode due to interrial evaporation of condensate water.
- Code “E5” alerts you the internal tank has become full. Please drain the air conditioner according to the instructions in User Manual.
- Before moving the unit. place a pan on the floor beneath the drain cover and remove the drain cover to drain the water.
- Be sure to replace the drain cover when draining is complete
Draining the Air Conditioner (Heat Pump models only
- Uncover the primary drain port..
- Connect the drain hose to the prima- ry drain hose. Make sure the connec tor does not have a water leak..
- Place the other end of drain hose into a drain, Check to see that the hose lies flat and is in the drain, Make sure the hose end that goes to the drain is on a lower level than the hose end that connects to the unit. The hose should not be kinked or pinched.
A. Primary drain hole
B. Primary drain port
C. Drain hose
See the user manual for detailed instruction on installation and using the features and settings of the air conditioner and remote control.
For questions about features, operation/performance, parts or service, Call: 1-855-344-7367
Monday to Friday: 8:00 am.-8:00p.m. (EST) or Visit: www.lisense- canada.com
The figures in this manual are based on the external view of a staridand model.. They may differ from that of the air conditioner you have selected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>