AMADA TZESD6 Electric Standing Desk Instruction Manual

AMADA TZESD6 Electric Standing Desk

Thank you

Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.

Model:
TZESD6B / TZESD6V / TZESD6N
TZESD7B / TZESD7V / TZESD7N
TZESD8B / TZESDBV / TZESDBN
TZESD19B / TZESD19V / TZESD19N

Specifications

Height Adjustment Range:

27 .5″ – 46.4″ (70cm-118cm)

Power Input 100V-240V

Max. Speed 25mm/s

Operating Noise <50db

Load Capacity 176 lbs / 80kg

Tools Needed (not included)

Drill

Phillips Screwdriver

Supplied Parts and Hardware for Step 1

A, x12 Bolt M6 x 30mm

B, x4 Bolt  M6 x 10mm

C, x2 Set Screw

D, x1 Allen Wrench 5/32″ (4mm)

01 x1 Crossbar

02 x1 Left Desk Leg

03 x1Right Desk Leg

04×2 Leg Base

05 x2 Side Plate

06 x1 Transmission Rod

08 x1 Rod Coupler

09 x1Wrench

Supplied Parts and Hardware for Step 2

Screw ST5 x 14mm E x6

Desktop Panel Connector F x3

Desktop 10 x1

Note: An extra wood dowel pin is provided for the longer 55″ / 63″ desk.

Wood Dowel Pin X 5 (for 40″ / 48″) X 6 (for 55″ / 63″) G

Supplied Parts and Hardware for Step 3

Screw ST5 x 14mm  E x16

Storage Hook 07 x1

AC Adapter Holder 11×1

AC Adapter 12×1

Controller 13×1

Supplied Parts and Hardware for Step 4

Power Cable 14 x1

Cable Clip 15 x4

Supplied Parts and Hardware for Step 5

Side Pocket 16 x1

Bolt M6 x 10mm B x1

Allen Wrench 5/32″ (4mm) D x1

Step 1 : Assembling the Frame

Align holes in the crossbar with holes in the desk legs, and insert four bolts. Partially and then fully tighten each pair of bolts.

Attach the side plates.

Slide the rod coupler onto the end of the motor drive shaft on the right leg.

Adjust uneven desk legs:

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod, using the wrench, to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to raise the left leg or anti-clockwise to lower it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Slide the rod coupler to the left to connect with the other end of the transmission rod.

Note: If the transmission rod doesn’t fit smoothly into the hole of rod 06 coupler, fine-tune flt with the wrench.

Use the set screws to secure the rod coupler.

Ensure the rubber pads are attached to the frame. If any have fallen off, reattach them or use the spare rubber pads.

Step 2: Assembling the Desktop

For the 40″ / 48″ long desk, use the five wood dowel pins to join the two desktop panels together.

For the 55″ / 63″ long desk, use the six wood dowel pins to join the two desktop panels together.

Secure the desktop panels with the connectors.

You can use a drill (with suitable torque and speed) or a Phillips screwdriver.

Drill (not included)

Phillips Screwdriver (not included)

Step 3: Attaching the Desktop

Attach the frame to the desktop.

Note: An off-center screw hole is not a problem. The pre-drilled holes are only guides for easier screw-in. If you have any questions or issues, please contact us at help_service_center@outlook.com.

Put the AC adapter into the holder.

Attach the storage hook, controller, and AC adapter with holder to the desktop.

Step 4: Connecting the Cables

Step 5: Attaching the Side Pocket

Thread the bolts through the holes in the side pocket and the side plate from the outside.

Using the Controller

Note: Ensure that there are no obstacles when using the desk, that the desktop is not right next to the wall, and that all cables are long enough for the desk to move up and down freely. When the controller screen is off (power saving mode), press any button to wake it before operating the desk.
Suggestion: Set the most comfortable height when you sit down to [1] and the most comfortable height when you stand up to [2] . The other two presets can be set for another user or to other heights you want to use.

Raise the Desk
Press the button to raise the desk continuously until it reaches the highest position of 46.4″
(118cm) or the button is released.

Lower the Desk
Press the button to lower the desk continuously until it reaches the lowest position of 27.5″ (70cm) or the button is released.

Save Height Settings
Four heights can be stored. Press and hold the [1][2][3][4] button for 3 seconds. The digital number will flash three times and the current height will be stored to that button.

Select Height Setting 1
Press the [1] button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

Select Height Settings 2
Press the [2] button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.
Select Height Settings3
Press the [3] button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.
———————————
Select Height Setting 4
Press the[4] button, and the desk will move to the height that was previously set for that button.
Press any button to stop the desk.

Settings

Reset|

1. Press and hold the button until the desk goes down to its lowest level, and then release the button.
2. Press and hold the button for 5 seconds until the screen displays ‘RST,’ and then release the button with ‘RST’ flashing.
3. Press and hold it again until the desk goes down to its lowest level and comes back up slightly. The screen will display current height again, and reset is complete.

Lock/Unlock| Press and hold [1] and [2] buttons together for 3 seconds to turn the lock on. The screen will display ‘LOC’ and the buttons will be disabled. Repeat to turn the lock off again.
Change Display Height Units| Press and hold [1] and [3] buttons together for 3 seconds to switch the display height unit. The default unit is imperial.
Change Collision Detection Sensitivity|

1. Press and hold [1] and [4] buttons together for 3 seconds, and ‘S02’ will flash on the screen. The last digit displayed is the current sensitivity level, and the value range is 0-3 (0: off; 1-3: highest to lowest).
2. Select other levels by pressing [ ] or button, and then press and hold [1] and [4] buttons together for 3 seconds. The digits will stop
   flashing, and the screen will display current height again.

Set/Clear Lowest Limit|

1. To set the lowest height limit, press and hold and [1] buttons together for 3 seconds, and the screen will display ‘-dO’ Whenever the desk reaches the lowest limit, the screen will display ‘-LO.
2. To clear the lowest height limit, move the desk down to the lowest height (screen displays ‘-LO’) and press and [1] buttons together for 3 seconds. ‘-dO’ will flash on the screen, and the limit will be cleared.

Set/Clear Highest Limit|

1. To set the highest height limit, press and hold [] and [1l buttons
   together for 3 seconds, and the screen will display ‘-UP’ Whenever the desk reaches the highest limit, the screen will display ‘-HI.’

2. To clear the highest height limit, move the desk up to the highest height (screen displays ‘-HI’) and press and [1] buttons together for 3 seconds. ‘-UP’ will flash on the screen and the limit will be cleared.

Troubleshooting

1. Please try resetting the desk if you have any issues like the following:
   • Abnormal operation.
   • The controller screen displays ‘RST’ (reset).
   • The controller screen displays error message E07 or E08, but the motor cable is connected correctly.
2. If the controller screen displays ‘HOT,’ please wait 20 minutes for the motor to cool down before making any further height adjustment.

Thank you again for choosing this product!

All of us do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry.
Should you have any issues, please don’t hesitate to contact us.
877-201-4016
help_service_center@outlook.com 860-00477-00 Rev09

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>