SUNNY HEALTH FITNESS SF-S020027SMART Smart Twist Stair Stepper Machine with Handlebar User Manual

SMART STAIR STEPPER MACHINE
WITH HANDLEBAR
SF-S020027 SMART
USER MANUAL

IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE
CONTACTED US: support@sunnyhealthfitness.com or 1- 877 – 90SUNNY (877-907-8669).

IMPORTANT SAFETY INFORMATION

We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is  assembled, maintained, and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions.

1. Before starting any exercise program, you should consult your physician to determine if you have any medical or physical conditions that could put your health and safety at risk or prevent you from using the equipment properly. Your physician’s advice is  essential if you are taking medication that affects your heart rate, blood pressure, or cholesterol level.

2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health.
   Stop exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If you do experience any of these conditions, you should consult your  physician before continuing with your exercise program.

3. Keep children and pets away from the equipment. The equipment is designed for adult use only.

4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
   To ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.

5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of the equipment can only be maintained if it is regularly examined for damage and/or wear and tear.

6. Always use the equipment as indicated. If you find any defective components while assembling or checking the equipment, or if you hear any unusual noises coming from the equipment during exercise, discontinue use of the equipment immediately and do not use until the problem has been rectified.

7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become entangled in the equipment.

8. Do not place fingers or objects into the moving parts of the equipment.

9. The maximum weight capacity of this unit is 250 lbs (110 kgs).

10. The equipment is not suitable for therapeutic use.

11. To avoid bodily injury and/or damage to the product or property, proper lifting and moving are required.

12. Your product is intended for use in cool and dry conditions. You should avoid storage in extreme cold, hot or damp areas as this may lead to corrosion and other related problems.

13. This equipment is designed for indoor and home use only; it is not intended for commercial use.

PRE-ASSEMBLY CHECK LIST

Before you start to assemble, please make sure all parts are included.

No.| Description| Spec.| Qty.| | No.| Description| Spec.| Qty.
---|---|---|---|---|---|---|---|---
1| Main Frame| | 1| 48| Upper Handlebar| | 1
32| Computer| DSC 03601- APP| 1| A| Hardware Package| | 1
34| Bottom Handlebar Post| | 1| B| Manual| | 1
35| Upper Handlebar Post| | 1| C| Thank You Card| | 1
36| Handlebar| | 1| D| Battery| AA| 2
42| Device Holder| | 1| | | |

HARDWARE PACKAGE

Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:

• The model number (found on cover of manual)
• The product name (found on cover of manual)
• The part number found on the “EXPLODED DIAGRAM”(12) page and “PARTS LIST” (page 13)

Please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).

ASSEMBLY INSTRUCTIONS

We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877907-8669).

STEP 1:
Remove the Main Frame (No. 1) from the box.
Lift one pedal of Left or Right Pedal (No. 8 or No. 13) up with your hand and ensure that the Wire Rope (No. 22) is put in the slot of the Pulley (No. 16) as shown in the picture.
STEP 2:
Then insert the Adjustment Knob (No. 21) into the Main Frame (No. 1), and adjust the tightness of the Adjustment Knob (No. 21) to the desired position.

STEP 3:
Connect the Sensor Wire (No. 28) with the Extension Wire (No. 46).
Insert the Bottom Handlebar Post (No. 34) into the Main Frame (No. 1) with 5 Hexagon Bolts (No. 40) and 5 Curved Gaskets (No. 41).
Tighten with the Allen Wrench (No. 55).

STEP 4:
Connect the Extension Wire (No. 46) with the Extension Wire (No. 43).
Insert the Upper Handlebar Post (No. 35) into the Bottom Handlebar Post (No. 34), adjust the Upper Handlebar Post (No. 35) to desired height, then secure it in place by inserting and tightening the Adjustment Knob (No. 15) from hardware package.

STEP 5:
Attach the Handlebar (No. 36) onto the Upper Handlebar Post (No. 35) with 2 Hexagon Bolts (No. 39). Tighten with the Allen Wrench (No. 55).

STEP 6:
Attach the Upper Handlebar (No. 48) onto the Handlebar (No. 36) with 2 Hexagon Bolts (No. 38). Tighten with the Allen Wrench (No. 55).
NOTE: Please attach Side A of the Upper Handlebar (No. 48) onto the Handlebar (No. 36) first, and then repeat the same step for Side B.

STEP 7:
Remove the Butterfly Nut (No. 52) and the Flat Washer (No. 53) from the Device Holder (No. 42).
Attach the Device Holder (No. 42) onto the Bracket (No. 54) using the Butterfly Nut (No. 52) and the Flat Washer (No. 53) that were removed, tighten and secure with your hand.
NOTE: When assembling the Device Holder (No. 42), ensure that it is aligned to the Bracket (No. 54) slot.

STEP 8:
Connect the Extension Wire (No. 43) to the Computer Wire (No. 32a). Then attach the Computer (No. 32) to the bracket of the Handlebar (No. 36).
The assembly is complete!

MAINTENANCE & ADJUSTMENT GUIDE

ADJUSTING THE STEPPING HEIGHT
Turn the Adjustment Knob (No. 21) clockwise to increase the stepping height.
Turn the Adjustment Knob (No. 21) counter-clockwise to decrease the stepping height.

ADJUSTING THE HEIGHT OF HANDLEBAR
Turn the Adjustment Knob (No. 15) counter-clockwise and pull out it from Bottom Handlebar Post (No. 34). Adjust the Upper Handlebar Post (No. 35) to desired position, then insert and re-tighten the Adjustment Knob (No. 15) by turning it clockwise.

CLEANING
The stepper can be cleaned with a soft, clean, and damp cloth. Do not use abrasives or solvents on plastic parts. Please wipe your perspiration off the stepper after each use. Be careful not get excessive moisture on the computer display panel as this might cause  electrical hazards or electronics failure.
Please keep the stepper, especially the computer, out of direct sunlight to prevent screen damage.
Please inspect all assembly bolts and pedals on the stepper for proper tightness every week.
STORAGE
Store the stepper in a clean and dry environment, away from children.
NOTES:
Do not use the stepper for more than 15 minutes as the hydraulic cylinders may overheat and become damaged. Allow at least 30 minutes rest in between sessions.

BATTERY INSTALLATION AND REPLACEMENT

BATTERY INSTALLATION:

1. Take out 2 AA batteries from computer box.
2. Press the buckle of battery cover on the Computer (No. 32), then remove battery cover.
3. Install 2 AA batteries into the battery case on the back of the Computer (No. 32). Pay attention to the battery + and – poles before installing.
4. Press the buckle of battery cover, then put the battery cover back to the back of the Computer (No. 32).

The installation is complete!

BATTERY REPLACEMENT:

1. Press the buckle of battery cover on the back of the Computer (No. 32), then remove battery cover.
2. Remove the 2 old AA batteries in the battery case and install 2 new AA batteries into the battery case on the back of the Computer (No. 32). Pay attention to the battery + and – poles before installing.
3. Press the buckle of battery cover, then put the battery cover back to the back of the Computer (No. 32).

The replacement is complete!
NOTE: Dispose battery according to your state and regional guidelines.

EXERCISE COMPUTER

SPECIFICATIONS:
ALORIES (CAL)——————————-0~9999 KCAL
COUNT (CNT)———————————–0~9999
TIME———————————————–00:00~99:59 MIN/S
TOTAL COUNT (TOT. CNT)—————–0~9999

KEY FUNCTIONS：
MODE:

1. This key lets you to select and lock on to a particular function you want.
2. Hold the key for 2 seconds to reset all values except TOT.CNT.

FUNCTIONS:

1. CALORIES (CAL): Display calories burned during exercise.
2. COUNT (CNT): Accumulates the count of steps taken while exercising. Computer counts 1 step after you step once with each foot.
3. TIME: Display the workout time elapsed during exercise.
4. TOTAL COUNT (TOT. CNT): Display the total steps taken while exercising. To reset TOTAL COUNT (TOT. CNT), you need to remove the battery and reinsert.
5.  SCAN: The computer will rotate through the four functions in the following order: CALORIES—TIME—TOTAL COUNT. Each function will be held for 6 seconds.

NOTE:

1. Without any incoming signals in 4-5 minutes, the LCD display will be shut off automatically.
2. When machine is in use, the computer automatically turns on.
3. If computer display is abnormal, please replace the battery and try again.
4. The computer use 2/AA batteries.

APP CONNECTION:
Connect Smart Equipment to SunnyFit App:

1. Scan to download SunnyFit from the app store:
   https://sunnyfitapp.sng.link/Alaco/l0xg?_dl=sunny- nebula%3A%2F%2Fsunny.amoyyg.com&_smtype=3

2. Ensure that the Bluetooth function is turned on from your mobile device.

3. If this is your first time using the SunnyFit app, follow the in-app instructions to register for your free SunnyFit account and log in.

4. Begin any workout activity that matches your smart equipment, then follow the onscreen prompts to search for and connect to your smart equipment.

5. When connected, your stats and records will be displayed at the end of your course/session, and recorded in your account profile!

Troubleshooting:

• If you are having trouble connecting your smart equipment, visit www.sunnyfit.com/guide or scan the QR code below:
  https://www.sunnyfit.com/guide?utm_source=productmanual&utm_medium=print&utm_campaign=manualtoguide

• If you require additional support, please contact support@sunnyfit.com

EXPLODED DIAGRAM

No.| Description| Spec.| Qty.| | No.| Description| Spec.| Qty.
---|---|---|---|---|---|---|---|---
1| Main Frame| | 1| 29| Sensor Holder| 0170118| 1
2| Left Foot Tube| | 1| 30| Foot Pad| 58.433.720| 4
3| Right Foot Tube| | 1| 31| Nylon Nut| M6| 4
4| Pully Fixed Bracket| | 1| 32| Computer| DSCO3601-APP| 1
5| Cushion| 03020| 2| 32a| Computer Wire| | 1
6| Hexagon Bolt| M620S5| 2| 33| Flat Washer| 01205.21| 2
7| Hexagon Bolt| M820S5| 4| 34| Bottom Handlebar Post| | 1
8| Left Pedal| 373`15182| 1| 35| Upper Handlebar Post| | 1
9| Cover| | 2| 36| Handlebar| | 1
10| Bushing| 038g:119.112| 4| 37| Foam Grip| 029023410| 2
11| Hexagon Bolt| M510S3| 6| 38| Hexagon Bolt| M615| 2
12| Magnet| cD1701112| 1| 39| Hexagon Bolt| M835| 2
13| Right Pedal| 37315182| 1| 40| Hexagon Bolt| M816S5| 5
14| Bushing| | 1| 41| Curved Gasket| d80202R25| 5
15| Adjustment Knob| M161.520037| 1| 42| Device Holder| | 1
16| Pulley| 010008.220| 1| 43| Extension Wire| 550MM| 1
17| Limit Plate| | 1| 44| Screw| ST38| 1
18| Hexagon Bolt| M84015S6| 1| 45| Magnet Cover| 0153.5| 1
19| Nylon Nut| M8| 2| 46| Extension Wire| 680MM| 1
20| Hydraulic Cylinder| 38| 2| 47| Foam Grip| 029(4)231 30| 2
21| Adjustment Knob| 060M14| 1| 48| Upper Handlebar| | 1
22| Wire Rope| 06.5365| 1| 49| Flat Washer| cD1608.21.5| 1
23| Plastic Gasket| 016010.21| 2| 50| Bushing| 022(1)20(4)811| 2
24| Alloy Wrap| | 2| 51| Hexagon Bolt| M875S5| 1
25| Hexagon Bolt| M103020S6| 2| 52| Butterfly Nut| M6| 1
26| Nylon Nut| M10| 2| 53| Flat Washer| 018(4)6.51.5| 1
27| Hexagon Bolt| M63610*S5| 4| 54| Bracket| | 1
28| Sensor Wire| | 1| 55| Allen Wrench| S5| 1

DOWNLOAD
Track your fitness progress & join
FREE workout courses!
Download SUNNYFIT today

FOLLOW
Find us on social media @sunnyhealthfitness
@sunnyhealthfitness
@sunnyhealthandfitness
@sunnyhealthfit
/sunnyhealthfitness
**** /sunnyhealthfitness
/sunnyhealthandfitness

www.sunnyhealthfitness.com

References

• SunnyFit | For Everyone

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>