Hampton MHDC134M Smart WIFI DC Ceiling Fan Installation Guide
- June 17, 2024
- HAMPTON
Table of Contents
AVOCA DC Series
Installation Guide
MHDC134M Smart WIFI DC Ceiling Fan
Thanks for choosing our Avoca DC Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
MHDC134M1230mm 4 Blade DC WiFi Ceiling Fan Malack
MHDC134W1230mm 4 Blade DC WiFi Ceiling Fan Mahite
MHDC134WO1230mm 4 Blade DC WiFi Ceiling Fan Mahite/Oak
MHDC1343M1230mm 4 Blade DC WiFi Ceiling Fan Malack with light
MHDC1343W1230mm 4 Blade DC WiFi Ceiling Fan Mahite with light
MHDC1343WO1230mm 4 Blade DC WiFi Ceiling Fan Mahite/Oak with light
Part List:
Qty 1x Motor assembly Qty 1x Instruction manual
Qty 1x Screw kit
Qty 1x Mounting Bracket
Qty 1x Remote & Receiver Qty x Blades
Application
How to Assemble
Secure the hanger bracket to ceiling beam or a suitable piece of timber inserted between the ceiling beams using the two long screws, or the four shorter screws supplied with the package.
Connect to mains as illustrated
Wire up the receiver with quick connectors and insert into the mounting
bracket. Please make sure the antenna wire has been safely folded inside the
canopy cover before final assembly (DO NOT cut the antenna wire)
Important Reminders
Receiver must be correctly installed in the mounting bracket
When the transmitter cannot control the receiver, please check
i) has sufficient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause
interference
Replace battery if getting low as this will affect sensitivity of the
transmitter
Take the battery out from the transmitter when leaving used for a long time to
avoid battery leaks Isolation switch MUST be connected in the line
Install the blades to the bottom of the motor. Tighten and secure
blade with screw and washer provided. Repeat this procedure until all blades
are installed.
NB: Ensure the blades do not get damaged or bent during the installation
process while the fan maybe on the ground, this will affect the performance
and balance of the fan and this is NOT covered under warranty
Install the cover as illustrated to finish the installation.
If you are installing model with LED light, GO TO the next step.
Install the LED light plate onto the steel bracket as illustrated with the 3
supplied screws.
Connect LED with power by the quick connectors.
WARNING Installation MUST carry out by a qualified and licensed electrician.
WiFi / Remote Control Pairing
Fan only model
Pairing the remote control
- Turn on the ceiling fan.
- Within the first 20 seconds, continue pressing the ( ) button until you hear a “beep” sound. ie. It is paired.
If you don’t hear a “beep” sound, repeat step 1 and step 2 again.
Entering WiFi Pairing mode:
- Turn on the power.
- Within the first 20 seconds, press and hold the “button until a beep is heard.
- Continue step connect on your smart devices to complete the pairing. If you don’t hear a “beep” sound, repeat the above steps.
FAN OFF : to switch off the fan.
SLEEP MODE : Turn on the fan at an extra lower speed to create a general
breeze.
SPEED BUTTON: 1 = lowest speed. 6 = highest speed.
NATURAL WIND MODEE : designed for the elderly and children. 1-6 speed changes
randomly to feel the breeze.
FORWORD AND REVERSAL ( ) : summer/winter reverse mode.
TIMER 1H/4H/8H: preset timer for fan and light to stop automatically. ie. if
timer set at 1H and then press 4H, fan will stop at 4H. Setting default to
last press.
WIFI BUTTON Follow the instructions and press and hold for 20 seconds to enter
wifi matching mode.
Fan LED Light Model
Pairing the remote control
- Turn on the ceiling fan.
- Within the first 20 seconds, continue pressing the button until you hear a “beep” sound. ie. It is paired.
If you don’t hear a “beep” sound, repeat step 1 and step 2 again.
Entering WiFi Pairing mode:
- Turn on the power.
- Within the first 20 seconds, press and hold the “ button until a “beep” is heard.
- Continue step connect on your smart devices to complete the pairing.
If you don’t hear a “beep” sound, repeat the above steps.
FAN OFF : to switch off the fan.
SLEEP MODE : Turn on the fan at an extra lower speed to create a general
breeze.
SPEED BUTTON: 1= lowest speed. 6 = highest speed.
NATURAL WIND MODE : designed for the elderly and children. 1-6 speed changes
randomly to feel the breeze.
FORWORD AND REVERSAL ( ): summer/winter reverse mode.
TIMER 1H/4H/8H: preset timer for fan and light to stop automatically. ie. if
timer set at 1H and then press 4H, fan will stop at 4H. Setting default to
last press.
LIGHT ON/OFF : to switch off the light.
CCT : warm white (2700K) / netural white (4000K) / cool white (6500K)
LED- LED+ : minus “-” = reduces brightness plus “+= increases brightness
WARNING
- Installation of fans MUST follow SAA standards and meet local authority regulations.
- Installation MUST be carried out by a qualified and licensed electrician.
- Fan and light MUST be earthed.
- Bracket MUST be firmly attached to a flat solid structure or timber frame.
- DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
- The warranty is VOID if product is not installed according to this installation guide.
WARNING Installation MUST carry out by a qualified and licensed electrician.
Smart Life matching process, please follow the steps:
-
Download the “Smart Life” APP on your smart devices by scanning the QR code below with camera. https://smartapp.tuya.com/smartlife
-
Turn on WiFi and Bluetooth on your smart devices. Ensure it’s connected to a 2.4GHZ WIFi
-
Open the APP, follow the steps to register new user account or login existing account.
-
Follow instructions in main manual (steps can also be found on the back of the remote) to put the fan into WiFi 1 pairing mode. If the operation is successful, go to step 6. If the fan has previously been paired or you can’t get it to work, please go to step 5 to RESET the fan.
-
RESET the fan. This step is NOT necessary if the fan has, successfully entered WiFi pairing mode in the last step, if 1 not, try to RESET the fan: turn on the fan, power off after , 10 seconds, power on again after 15 seconds, long press
1 “Fan Stop” for 5 seconds, if “beep beep” are heard, the : reset is successful. If “beep beep” is not heard, the reset is failed, please repeat this step. -
Once the fan has entered WiFi pairing mode, open the APP again on the smart device. Click “Add Device” in the middle or the “+” on the top right of the screen.
-
The auto scan should begin automatically, and the fan should show up at the top of screen within a few seconds.
Note: If the fan is not showing up, you can add it manually by clicking and navigate to: >Add Manually >Small Home Appliance > Fan -
Follow instructions in the APP to finish the set up.
Wire Connections
6 Year Warranty
Visit our website for details https://www.martecaustralia.eom.au/warranty-
statementl
WARNING
- Installation of fans MUST follow SAA standards and meet local authority regulations.
- Installation MUST be carried out by a qualified and licensed electrician.
- Fan and light MUST be earthed.
- Bracket MUST be firmly attached to a flat solid structure or timber frame.
- DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
- The warranty is VOID if product is not installed according to this installation guide.
E:sales@martecltd.com.au I P: 02 8778
7500
www.martecaustralia.com.au
Documents / Resources
|
Hampton MHDC134M Smart WIFI DC Ceiling
Fan
[pdf] Installation Guide
MHDC134M Smart WIFI DC Ceiling Fan, MHDC134M, Smart WIFI DC Ceiling Fan, WIFI
DC Ceiling Fan, DC Ceiling Fan, Ceiling Fan, Fan
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>