ALPINE EX-10 iPod Controller With Bluetooth Instruction Manual

ALPINE EX-10 iPod Controller With Bluetooth

Product Information

Specifications

• Display unit
• Display mount
• Display cable
• Cigarette Lighter Adapter
• Antenna
• Bluetooth microphone
• Power supply
• iPod cable
• Remote control
• Power Cable
• Accessory kit (remote control battery, microphone clip, cable clips, etc.)

Product Usage Instructions

Installation Options

• Option #1: Install it yourself. Follow the instructions in this manual to perform a simple, do-it-yourself installation.
• Option #2: Have it professionally installed. Go to www.alpine-usa.com, click Support, then click Locate a Dealer to find an authorized Alpine dealer in your area to install your new eX-10.
• Alpine dealers have many options to enhance the audio and cosmetic integration of the eX-10 in your vehicle.*
• Note: Professional installation and other hardware may require an additional cost.

Do-It-Yourself Installation

Step 1: Mount the display

1. Push the display into the display mounting bracket until you hear a click.

Step 2: Mount the Bluetooth Microphone

1. Attach the Bluetooth microphone to the microphone mounting clip by pushing the microphone onto the clip as shown.
2. Apply the supplied double-sided tape to the bottom of the display, clean the desired spot on your dash* with the supplied alcohol pad, then firmly stick the display to the dash.
3. Clip the microphone mount to a spot in your car no more than 24″ from your mouth.

Note: Mount the eX-10 display in a location where it will not block your view of the road.

Step 3: Connect the wiring

1. Plug the display cable into the back of the display, and use the supplied cable clamps to route the cable to the power supply location. Take care to route the cable away from moving parts such as shifters, pedals, and steering wheels.
2. Screw the yellow end of the power cable into the eX-10’s power supply, and screw the black end into the cigarette lighter adapter.
3. Now the cigarette lighter adapter and the power supply are ready to be installed. Plug the cigarette lighter adapter into your cigarette lighter plug.
4. Plug the iPod cable into the port marked iPod on the power supply. Plug the square end of the monitor cable into the port marked MONITOR on the power supply.

FAQ (Frequently Asked Questions)

Q: Where can I find more detailed information and support for operating or installing the eX-10?

• A: You can download the owner’s manual and get additional help at http://www.alpine-usa.com/US-en/support.
• If you would like to speak to Alpine customer support concerning eX-10 operation or installation, please call 1-800-ALPINE-1.

Q: Where can I find an authorized Alpine dealer for professional installation?

• A: Go to www.alpine-usa.com, click Support, then click Locate a Dealer to find an authorized Alpine dealer in your area.

Installation Options

• Here’s how to install your new eX-10 in your vehicle.

Option #1: Install it yourself

• Follow the instructions in this manual to perform a simple, do-it-yourself installation.

Option #2: Have it professionally installed

• Go to www.alpine-usa.com, click “Support”, then click “Locate a Dealer” to find an authorized Alpine dealer in your area to install your new eX-10.
• Alpine dealers have many options to enhance the audio and cosmetic integration of the eX-10 in your vehicle.

Here’s what’s in the box

Note: Professional installation and other hardware may require an additional cost.

Do-It-Yourself Installation

Here’s how to install your new eX-10 in your vehicle.

Step 1: Mount the display

• Push the display into the display mounting bracket until you hear a “click.
• Apply the supplied double-sided tape to the bottom of the display, clean the desired spot on your dash* with the supplied alcohol pad, then firmly stick the display to the dash.
• Note: Mount the eX-10 display in a location where it will not block your view of the road.

Step 2: Mount the Bluetooth Microphone

• Attach the Bluetooth microphone to the microphone mounting clip by pushing the microphone onto the clip as shown.
• Clip the microphone mount to a spot in your car no more than 24” from your mouth.
• Good locations include the sun visor, the top of the A-pillar, and the edge of your roof-mounted center console (if equipped).

Step 3: Connect the wiring

• Plug the display cable into the back of the display, and use the supplied cable clamps to route the cable to the power supply location.
• Take care to route the cable away from moving parts such as shifters, pedals, and steering wheels.
• Screw the yellow end of the power cable into the eX-10’s power supply, and screw the black end into the cigarette lighter adapter.
• Now the cigarette lighter adapter and the power supply are ready to be installed.
• Plug the cigarette lighter adapter into your cigarette lighter plug.
• Plug the iPod cable into the port marked “iPod” on the power supply.
• Plug the square end of the monitor cable into the port marked “MONITOR” on the power supply.
• Plug the antenna into the port marked “ANTENNA” on the power supply.
• Plug the Bluetooth microphone into the port marked “MICROPHONE” on the power supply.
• Place the power supply into a hidden location in your car, like inside the center console or the glove box. Use the supplied hook-and-loop fastening tape to secure it.

Step 4: Plug in your iPod

• Plug your iPod into the dock connector.
• Place the iPod in a convenient location. In most applications, it can be placed next to the power supply.
• The eX-10 controls and charges your iPod, so no need to mount it where you have access to the iPod’s controls.
• The installation is complete! Turn on your car’s ignition and power up the eX-10.
• Next, let’s get the eX-10 set up to work correctly in your car.

Set up your eX-10

• Here’s how to get your eX-10 working properly in your car.
• Step 1: Select your language and set the output mode
• Push the “SETUP” button, then use the button to scroll down to “General”.
• Tap “ENTER” twice, then select your language using the and buttons. Tap “ENTER” to select.
• You’re still in “SETUP” mode, so tap the button three times until you get to “Output Mode”.
• Tap “ENTER”, and use the button to select Wire Transmitter”. Press “ENTER” to select Wire Transmitter” mode.
• Now, tap the button to get back to the SETUP” menu.

Step 2: Set up your car’s radio to work with the eX-10

• The eX-10 broadcasts audio to your car stereo just like an FM radio station.
• Tune your car radio to an FM frequency where there is no radio reception (for example, 88.3MHz).
• Save a few of these blank stations in your car radio’s preset memories for use with the eX-10’s FM transmitter.
• Select “Transmitter” from the eX-10’s “SETUP menu, then press and hold “ENTER” for two seconds. Use the buttons to select the same frequency as shown on your car radio display.
• Press “ENTER” to set this frequency as a preset in the eX-10. You can set up to four different frequencies using this method*.
• Your car’s radio and the eX-10 must be tuned to the same frequency to hear the audio output.
• Note: If one of your selected frequencies encounters a strong FM signal while driving, interference may be heard while listening to an iPod or Bluetooth.
• Changing presets to match frequencies on both your car stereo and your eX-10 can solve this problem quickly.

Step 3: Set up your Bluetooth phone to work with your eX-10

• Tap the button, and press “ENTER” to select Bluetooth”. Press “ENTER” again to select Pairing Mode”, and a four-digit passcode will be displayed on the eX-10.
• The eX-10 is now discoverable and ready to connect to your Bluetooth phone.
• Turn on Bluetooth in your phone’s menu. Your phone will ask for a four-digit code to connect with the eX-10, so enter the code shown on the eX-10’s screen.
• You will now see a “Connected” message on the eX-10’s display to let you know that you’ve successfully paired your phone with the eX-10*.

Now we’re all set up, so let’s use the eX-10

• Note: Turn “Auto Connect” on in the Bluetooth setup menu if you want your phone to automatically connect to your eX-10 whenever you turn on your car’s ignition.

Use your eX-10

Here’s the basics on how to use your eX-10

Step 1: Playing songs from your iPod

• Use the button to exit the “SETUP” menu.
• Press “SOURCE” to select “iPod”.
• Press the “ENTER” button, then use the buttons to search by artist, album, song, etc. Tap “ENTER” to choose any search method, using the buttons to select a song.
• Pressing “ENTER” will begin song playback.
• With the song playing, you should now see the iPod’s album art displayed on the eX-10 screen.* Press the “VIEW” button to scroll between the three different display modes.
• You can also choose the display background that best matches your dash by selecting “DISPLAY” in the “SETUP” menu, then “BGV Select.
• Note: Album Art must be stored on your iPod to be displayed on the eX-10.

Step 2: Making and receiving phone calls

• Press the button, and use the and buttons to select “Phonebook”. Press “ENTER”, then use the and buttons to find the desired contact in your phone book.
• Press again to dial the number. You may also select numbers from the dialed, received, or missed call lists using this method.
• You will now hear the phone dialing through your car’s stereo system. To hang up, press When a call comes in, simply press to answer it.
• To hang up, press You can also select “Auto Answer” under Bluetooth” in the “SETUP” menu if you want the eX-10 to automatically answer any call that comes in.
• Note: All features are not enabled on all phones. Check with your phone service provider.
• Step 3: Listening to songs stored on your phone
• If your phone is Bluetooth audio enabled, you can play songs from your phone through the eX-10.
• Press “SOURCE” to select “Bluetooth Audio” mode, then use, and control the audio tracks.

How to learn more and get support

• If you want more detailed information on operating or installing the eX-10, you can download the owner’s manual and get additional help at http://www.alpine-usa.com/US-en/support
• If you would like to speak to Alpine customer support concerning eX-10 operation or installation,
• please call 1-800-ALPINE-1.
• Apple, the Apple logo, iPod and iTunes are registered trademarks of Apple Inc. The Bluetooth logo is owned by the Bluetooth SIG, Inc. and any use of such marks by Alpine Electronics, Inc. is under license.
• Product information listed in this guide is based upon current information at the time of printing, but cannot be guaranteed.
• All designs, features, and specifi cations are subject to change without notice.
• For updated product information, please visit www.alpine-usa.com. © 2008 Alpine Electronics Inc. All rights reserved.

References

• Alpine | Car Audio, Stereo, Speakers, Subwoofers, and Amps
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>