behringer OD300 Overdrive Distortion User Manual
- June 17, 2024
- Behringer
Table of Contents
behringer OD300 Overdrive Distortion
Thank you for showing your confidence in us by purchasing the Behringer OVERDRIVE DISTORTION OD300. This effects pedal is ideally suited for electric guitars. Thanks to its high-performance features you can create state-of-the- art overdrive, distortion or a combination of both effects.
Controls
- The LEVEL control adjusts the output level.
- The TONE control allows you to shape your overall sound.
- The DRIVE control adjusts the intensity of the overdrive/distortion effect.
- Use the MODE control to adjust the balance between the overdrive and distortion effect. In the leftmost position, you get a pure overdrive effect and in the rightmost position, you get pure distortion.
- The ON/BATT LED illuminates when the effect is activated. It also serves as a battery level indicator.
- Use the footswitch to activate/deactivate the effect.
- Use this ¼” TS IN connector to plug in the instrument cable.
- The ¼” TS OUT connector sends the signal to your amp.
Use the DC IN connection at the front of the unit to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery, press the hinges with a ballpen and remove the pedal cover. Be careful not to scratch the unit.
- The OD300 has no on/off switch. As soon as you insert the jack into the connector, the OD300 begins running. When not using the OD300, remove the jack from the in connector. This extends the life of the battery.
The SERIAL NUMBER is located at the bottom.
Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service the product yourself. Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged.
Limited Warranty
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
Specifications
In
- Connector ¼” TS
- Impedance 500 kΩ
Out
- Connector ¼” TS
- Impedance 1 kΩ
Power Supply
9 V ?, 100 mA regulated
Behringer PSU-SB
- USA/Canada 120 V~, 60 Hz
- China/Korea 220 V~, 50 Hz
- U.K./Australia 240 V~, 50 Hz
- Europe 230 V~, 50 Hz
- Japan 100 V~, 50 – 60 Hz
- Power connector 2 mm DC jack, negative centre
- Battery 9 V type 6LR61
- Power consumption 30 mA
Physical/Weight
- Dimensions (H x W x D)
- approx. 2 1/8 x 2 3/4 x 4 4/5″
- approx. 54 x 70 x 123 mm
- Weight approx. 0.73 lbs / 0.33 kg
Behringer is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may therefore differ from those listed or shown.
Music Tribe accepts no liability for any loss that may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
OVERDRIVE/DISTORTION OD300
- Responsible Party Name: Music Tribe Commercial NV Inc.
- Address: 5270 Procyon Street, Las Vegas NV 89118, United States
- Phone Number: +1 702 800 8290
OVERDRIVE/DISTORTION OD300
This equipment has been tested and found to comply with the limits for a Class
B digital device, under part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music
Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product complies with Directive
2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive
2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/.
EU Representative:
Music Tribe Brands DK A/S Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus
N, Denmark.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>