behringer HM300 Heavy Metal Distortion Effects Pedal User Manual
- June 17, 2024
- Behringer
Table of Contents
behringer HM300 Heavy Metal Distortion Effects Pedal
Thank you for showing your confidence in us by purchasing the Behringer HEAVY
METAL HM300. This high-quality effects pedal enables you
to produce super thick, tube-like distortion plus endless sustain. Thanks to
its high-performance features you can achieve the typical hard rock or heavy
metal distortion sounds.
Controls
-
The LEVEL control adjusts the output level.
-
The LOW control allows you to boost/cut the low-frequency range.
-
The MID control allows you to boost/cut the mid-frequency range.
-
The DIST control adjusts the amount of distortion effect and the length of the resulting sustain time. High distortion settings will cause longer sustain times.
-
The ON/BATT LED illuminates when the effect is activated.
It also serves as a battery level indicator. -
Use the footswitch to activate/deactivate the effect.
-
Use this ¼” TS IN connector to plug in the instrument cable.
-
The ¼” TS OUT connector sends the signal to your amp.
Use the DC IN connection to plug in a 9 V power supply (not included). The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery (not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful not to scratch the unit.
- The HM300 has no on/off switch. As soon as you insert the plug into the in connector, the HM300 is on. When not in use, remove the plug from the in connector. This extends the life of the battery. The SERIAL NUMBER is located at the underside.
Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service product yourself. Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged.
Limited Warranty
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
Specifications
In
- Connector ¼” TS
- Impedance 500 kΩ
In
- Connector ¼” TS
- Impedance 1 kΩ
- Power Supply 9 V , 100 mA regulated
- Behringer PSU-SB 100 – 240 V~, 50 – 60 Hz
- Power connector 2 mm DC jack, negative centre
- Battery 9 V type 6LR61
- Power consumption 30 mA
- Dimensions (H x W x D) 54 x 70 x 123 mm (2.1 x 2.8 x 4.8″)
- Weight 0.33 kg (0.73 lbs)
Behringer is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may therefore differ from those listed or shown.
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
HEAVY METAL HM300
- Responsible Party Name: Music Tribe Commercial NV Inc.
- Address: 5270 Procyon Street, Las Vegas NV 89118,
- United States
- Phone Number: +1 702 800 8290
HEAVY METAL HM300
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment. Hereby, Music Tribe declares that this product is in compliance with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC. Full text of EU DoC is available at
EU Representative: Music Tribe Brands DK A/S Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>