BMW JE1009 Battery Powered Ride On Kids Electric Car Owner’s Manual

BMW i4 JE1009 AA0044 AA0045 AA0046 AA0047
BATTERY POWERED RIDE-ON
Owner’s Manual
with Assembly Instructions

JE1009 Battery Powered Ride On Kids Electric Car

JE1009 AA0044 AA0045 AA0046 AA0047

The owner’s manual contains important safety information as well as assembly, use and maintenance instructions.
The Ride-on Car must be assembled by an adult who has read and understands the instructions in this manual.
Keep the package away from children and dispose of properly before use.
Keep this manual for future reference.

About Your New Ride-On

On the purchase of your new Ride-On.
This ride-on will provide your child with many miles of riding enjoyment. To help ensure a safe ride we ask you to please read this manual carefully, and keep it for future reference.
Please follow the recommendations in this manual, they are designed to improve the safety and operation of your ride-on car and it’s rider.
BMW i4 Children Battery Powered Ride-On manufactured by Zhejiang Jaimie Ride- On Co., Ltd. (Add: Xinyang Industrial Zone, Penghu City, Zhejiang Province, P.R.China). The BMW logo and the BMW word mark are trademarks of BMW AG and are used under license.

SPECIFICATIONS:

User Notice

WARNING!

• CHOKING HAZARD – Small parts. Not suitable for children under 36 months. The product contains small parts, keep children away when assembling.
• ADULT ASSEMBLY REQUIRED.
• Always remove protective material and poly bags and dispose before assembly.
• Protective equipment should be worn. Always wear shoes and sit in the seat when operating the vehicle.
• Only drive on level ground. Never use on the lawn.
• Keep your hands, hair, and clothes away from moving parts.
• Never leave child unattended. Direct adult supervision is required. Always keep child in view when child is in vehicle.
• To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water, always wear shoes, and never allow more than 1 rider.
• Never use in unsafe conditions such as snow, rain, loose dirt, mud, sand, or gravel, otherwise may result in an unexpected accident such as tipping over, and could damage the electrical system or battery
• Not to be used in traffic.
• This toy should be used with caution since skill is required to avoid falls or collisions causing injury to the user or third parties.
• This toy is unsuitable for children under 36 months due to its maximum speed; Maximum user weight is 30kg.
• This toy has no brake.

BATTERY INFORMATION

• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Different types of batteries or new and used batteries are not to be mixed.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.

WARNING!
The remote control is not a toy, and is only allowed to be operated by adults.

Parts Diagram

HINT: Some parts shown are assembled on both sides of vehicle

Parts List

Assembly tools required (not included):

Attach the Rear Wheels

Remove all the parts from the rear axle.

1. 1-

2. Fit the wheel driver to the wheel. Insert and tighten three Ø4×16 screws to secure the wheel driver to the wheel.

3.  Slide the wheel onto the rear axle (Left Side). Keep the wheel driver match up with the gear box on the rear axle.

4. Slide a Ø10 washer onto the rear axle.

5.  Tighten a lock nut to the end of the rear axle with a spanner.
   Repeat the above procedure to assemble the other Rear Wheel.
   HINT: An extra spanner has been provided to hold the Lock Nut on the other side of the rear axle while tightening the Lock Nut on the other side.

6.  Fit the hub caps to the wheels.

Attach the Front Wheels

Remove all the parts from the front axle.

1. Slide a Ø10 washer onto the front axle.
2. Slide a wheel onto the front axle.
3. Slide a Ø10 washer onto the front axle.
4. Tighten a lock nut to the end of the front axle with a spanner. DO NOT over tighten.
5.  “Snap” the hubcap to the wheel.
   Repeat the above procedure to assemble the other Front Wheel.

After assembling any wheel to the axles, please check the gap between the screw thread and the collapsible (refer to below picture), if the gap is too big, please add two or three washers inside the wheel, but after tightening the nut outside the wheel, please turn the wheel by your finger to check if the wheel can run smoothly, this is very important, because if the wheel can run smoothly, it is ok, but if the nut press the wheel and the wheel can’t run smoothly, the motor will be broken easily! Then you need to decrease one or two washers to make sure the wheel can run smoothly!

Attach the Dash & Steering Wheel

1. Plug the light unit connector on the dash into light connector on the vehicle body. Hide the plumed connectors into the hole in the vehicle body.

2. Fit the tabs on the dash into the holes in the vehicle body, and push until you hear it “click” into place.
   Please follow the steps 1-4 to add the batteries (Not Included), and refer to the battery information on page 2.

3. With a screwdriver loosen the screw on the battery cover located in the center of the steering wheel.

4. Remove the battery cover from the top of the battery compartment.

5. Insert 2×1.5 AA batteries in their correct polarities.

6. Place the battery cover over the battery compartment and fasten with the screw you loosened in step one.

Attach the Steering Wheel, Windshield & Side Mirrors

Attach the Steering Wheel
Remove the M5x35 machine screw and Ø5 nut from the steering wheel.
Turn the vehicle body upright.

1. Place the steering wheel over the the steering column, protruding from the middle of the steering wheel base.
2. Align the holes on each side of steering wheel with the holes at the end of the steering column.
3. Fasten a nut on the opposite end of the screw to secure the steering wheel to the steering column.
4. Fit the tabs windshield into the grooves on the vehicle. Press until you hear it “click” into place.
5. Fit the side mirrors to the holes on the both doors, push until you hear them “click” into place.

Connect the Power Supply & Attach the Seat

1. Plug the vehicle connector into the connector on the battery.
2. Fit the tabs on the seat back into the grooves on the rear of the vehicle.
3. With a screwdriver tighten the M5x16 screws on the top of the seat into the holes in the vehicle.

Use Your Ride-on

1. Power button: Turns the product on and off.

2. Foot pedal: Applies power (speed) to the product.
   ● To move the product, press the pedal down.
   ● To brake or slow down, release pressure from the pedal.

3. Forward/reverse level: Changes the direction that product moves from forward to reverse.
   ● To move the product forward, shift the lever to top position.
   ● To move the product backward, shift the lever to down position.

4. Sound buttons: Press for sound playing.

5. High/Low speed switch (if equipped):
   Operates the product to move forward in high speed and low speed.

IMPORTANT

• Always stop vehicle when changing the speed or direction to avoid damage the gears and motor.
• HIGH SPEED (If equipped): Make sure your child knows how to steer, how to start and stop the product and knows the rules for safe driving.

Use the 2.4G Remote Controller

WARNING: ADULT OPERATING REQUIRED!

1. Connect button (build connection)
   Lift the battery compartment door on the back of the controller and insert two AAA (LR03) batteries. NOTE: Batteries not included. Refer to the battery information on page 2.
   Press and hold the connect button for 3 seconds, the low-speed indicator flashes, mean that the remote controller is in the connected state. Then power on the vehicle:
   The low-speed indicator goes to long bright, means the connection successful.
   If the low-speed indicator no response, means the connection failed. Turn off the remote controller (by removing the batteries) and the vehicle. And try again.

2. Brake button
   Press the button to stop the vehicle, press it again to release the brake.

3. Speed select button
   The switch operates the vehicle to move in low, normal or high speed.
   HINT: The vehicle is designed to operate in low speed only in reverse.

NOTE:

• Leave the remote controller idling for about 10 seconds, it will shut down automatically.
• After you replacing the batteries of the remote controller, please rebuild the connection. (step 1)

Use the Audio Player (Wireless Connections)

A. Player Power.
B. Multimedia input: Allow the audio from your portable device to be played through the vehicle speakers.
C. 3.5mm AUX input: Allow the audio from your portable music player or phone to be played through the vehicle speakers.
D. Increase volume
E. Decrease volume
F. Storytelling mode
G. Wireless connections
H. Music mode
I. Previous
J. Play/pause
K. Next
L. Digital voltmeter: Check the power remaining of your battery. Check the power remaining of your battery. Please recharge the battery If the value is too low, refer to the .

Charging

WARNING!

• ONLY an adult is allowed charge and recharge the battery!

• This product with Charging Protection: when charging, all functions will be cut off.

• The POWER SWITCH must be turned in OFF position when charging.

• Before the first use, you should charge the battery for 4-6 hours. Do not recharge the battery for more than 10 hours to avoid overheating the charger.

• When the vehicle begins to run slowly, recharge the battery.

• After each use or once a month minimum recharge time as 8 to 12 hours, less than 20 hours at most.

• Use only battery(ies) and charger specified by the manufacturer. Using another battery or
  charger may cause a fire or explosion. Do not use the battery or charger for any other product.

• If your ride-on with a Digital voltmeter(IF EQUIPPED), the magnitude of voltage will tell you how much power is remaining in the battery when you must recharge the battery. Make sure the vehicle is stop!

Charging Way I

1. Plug the charger port into the input socket (the socket is below the seat ).
2. Plug the charger plug into a wall outlet. The battery will begin charging.

Battery Disposal
The battery will eventually lose the ability to hold a charge. Depending on the amount of use, and varying conditions, the battery should operate for one to three years.
Important! Recycle the dead battery responsibly. The battery contains lead acid (electrolyte) and must be disposed of properly and legally. It is illegal in most areas to incinerate lead acid batteries or dispose of them in landfills. Take it to  a federal or state-approved lead acid battery recycler, such as local automotive battery retailer.
Do not throw the battery away with your regular household waste!

Charging Way II

A: Use a screwdriver to loosen the two screws on the top of the seat and remove the seat.
B: Unplug the red connectors from each other.
C. Loosen the four screws around the battery box with a screwdriver and lift the battery box up.
D. Place the battery box on a flat ground. Plug the charger port into the input socket on the battery box.
E. Plug the charger plug into a wall outlet. The battery will begin charging.

Troubleshooting Guide

Vehicle does not run

| Battery low on power| Recharge battery.
Thermal fuse has tripped| Reset fuse, see
Battery connector or wires are loose| Check that the battery connectors are firmly plugged into each other. If wires are loose around the motor contact your distributor please.
Battery is dead| Replace battery, contact your distributor please.
Electrical system is damaged| Contact your distributor please.
Motor is damaged| Contact your distributor please.
Vehicle does not run very long

| Battery is under charged| Check that the battery connectors are firmly plugged into each other when recharging
Battery is old| Replace battery, contact your distributor please.
Vehicle runs sluggishly

| Battery low on power| Recharge battery, contact your distributor please.
Battery is old| Replace battery, contact your distributor please.
Vehicle is overload| Reduce weight on vehicle.
Vehicle is being used in harsh conditions| Avoid using vehicle in harsh conditions, see .
Vehicle needs a push to go forward

| Poor contact of wires or connectors| Check that the battery connectors are firmly plugged into each other. If wires are loose around the motor, contact your distributor please.
“Dead Spot” on motor| A dead spot means the electric power is not being delivered to the terminal connection and the vehicle needs repair. Contact your distributor please.
Difficult shifting from forward to reverse or vice-versa| Attempting to shift while the vehicle is motion| Completely stop the vehicle and shift, see <Use Your Ride-On>
Loud grinding or clicking noises coming from motor or gear box| Motor or gears are damaged| Contact your distributor please.
Battery will not recharge

| Battery connector or adapter connector is loose| Check that the battery connectors are firmly plugged into each other.
Charger not plugged in| Check that the battery charger is plugged into a working wall outlet.
Charger is not working| Contact your distributor please.
Charger feels warm when recharging| This is normal and not a cause for concern|

Maintaining

• It is parents’ responsibility to check main parts of the toy before using, Must regularly examine for potential hazard, such as the battery, charge, cable or cord, plug, screws are fastening enclosure of other parts and that in the event of  such damage, the toy must not be used until that damage had been properly removed.
• Park the vehicle indoors or cover it with a tarp to protect it from wet weather.
• Recharge the battery after each use. Only an adult can handle the battery. Recharge the battery at least once a month when the vehicle raider is not being used.
• Do not wash the vehicle with a hose. Do not wash the vehicle with soap and water. Do not drive the vehicle in rainy or snowy weather. Water will damage the motor, electric system and battery.
• Clean the vehicle with a soft, dry cloth. To restore shine to plastic parts, use a nonwaxy furniture polish. Do not use car wax. Do not use abrasive cleaners.
• When not using, all the electrical source should be turn off. Turn off the power switch and disconnect the battery connection.

Fuse
The battery features a thermal fuse with a rest fuse that will automatically trip and cut all power to the vehicle if the motor, electric system or battery is overloaded. The fuse will reset and power will be restored after the unit is turned OFF  for 20 seconds and then turned ON again. If the thermal fuse trips repeatedly during normal use, the vehicle may need repair. Contact your distributor please.
To avoid losing power, follow these guidelines:

• Do not overload the vehicle.
• Do not tow anything behind the vehicle.
• Do not drive up steep slopes.
• Do not drive into fixed objects, which may cause the wheels to spin, causing the motor to overheat.
• Do not drive in very hot weather, components may overheat.
• Do not allow water or other liquids to come in contact with the battery or other electric components.
• Do not tamper with the electric system. Doing so may create a short, causing the fuse to trip.

RISK OF FIRE. Do not bypass. Replace only with a new fuse.

Our products are suitable for
ASTM F963; GB6675; EN71 and EN62115 standard.
Styles and colo(u)rs may vary.
Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>