YESSOLDERER 110V Professional Home Welder Instructions
- June 17, 2024
- YESSOLDERER
Table of Contents
**YESSOLDERER 110V Professional Home Welder Instructions
**
Installation instruction
How do I properly install a welding helmet?
- Attach the snap fastener on the top of the helmet.
- Install the lens on the top notch of the helmet, rotate the lens clockwise to fix the lens.
- Install the grip on the bottom notch of the helmet to make it easy to hold.
How do I properly connect the cable to the connector?
- Soldering handle wire is connected to “+”.
- ground wire is connected to
Operation instruction
How to use the welding machine correctly?
- Welding handle wire is connected to the “+”, grounding wire is connected to the “-”.
- Clamp the welding rod with the welding handle wire.
- Turn on the control switch at the back of the welder.
- Adjust the current to the strength you need.
- Start welding work
Operational control
Front & rear control panel layout
- Alarm pilot lamp: This pilot lamp indicates when lit that the protection of the machine has been activated.
- Cooling vent: Promote air circulation.
- Liquid crystal display: display the value of real-time current.
- Current adjustment knob: set welding current (5 -140 A).
- Earth connection-” output.
- Welding connection ”+” output.
- Mains switch.
Welding method
- Knocking arc: When the end of the welding rod touches the surface of the workpiece vertically, the welding rod is quickly lifted up and kept at a certain distance, and the arc is ignited immediately.
- Scratch arc method: the end of the welding rod to the workpiece, and then like a match will scratch the welding rod in the surface of the workpiece gently, ignite the arc.
Operating Precautions
- Input power must be AC as one phase, 50 HZ, 110V .Forbid working in lacking any phase.
- In case closing the power switch, no load voltage may be exported. Do not touch the output electrode with any part of your body.
- Before operation, no concerned people should be left. Do not watch the arc in unprotected eyes.
- Ensure good ventilation of the machine to improve duty ratio.
- Turn off the welding machine when the operation finished to economize energy sources.
- When power switch shuts off protectively because of failure. Do not restart it until problem is resolved. Otherwise, the range of problem will be extended
Fault resolution
| SIN | Troubles | Reasons | Solutions |
|---|---|---|---|
| 1 | No current output for welding | The welding cable is not connected to the | |
| output end of the welding machine. | Connect the welding cable to the welder |
output
Power Supply PCB Failure| Refurbishment replacement of welding cables
Grounding cable not connected or loose| Check the Grounding cable
2| Turn on the power, the LCD display has a| There’s something in the fan|
Clearance of debris
value, but the fan does not work| Damaged fan motor| Replacement of fan motor
| Turn on the power, the LCD does not light up, the fan does not work| No
input voltageis input voltage| Check whether there
Overvoltage (is the input voltage too high)| Check input voltage
| Not easy to start the arc when welding easy to sticking| Loose or poorly
connected plug| Check the tighten the plug
Oil or dust on the workpiece| Check and clean up
5| The arc is not stable in the welding process| The arc force is too small|
Increase the arc force
6| Welding current cannot be adjusted| The welding current potentiometer in
the front panel connection not so good or damaged| Repair or replace
potentiometer
---|---|---|---
7| The penetration of molten pool is not enough (MMA)| Welding current
adjustment too low| Increase welding current
The arc force adjustment is too small| Increase the arc force
8| Arc blow| Airflow interference| Use the shelter from airflow
Electrode anomalies| Adjustment ofelectrode angle
Magnetically affect| Tilt the electrode in the opposite direction of the
magnetic strike
Change the position of the grounding clampor add grounding cables on both
sides of the workpiece
Use the short arc operation
9| Protection indicator lights up| Overheating protection| Exceeds welding
current| Pay attention to the welding current output
Extra long working hours| Interval work
Overcurrent protection| Abnormalcurrent in the main circuit| Test and repair
of main and driver boards
After-sales service
What if I have a problem with my product?
- Please contact us first if you have any problems, We can help you solve the problem.
* How to contact us:
- open your order.
- select Send Message.
- Send the relevant questions and provide the order number.
E-mail : 17615683296@163.com.
Thank you for your purchase of the company’s production of series inverter welding machine, for the correct use of this welder, please carefully read the instructions before use!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>