Contour Pro3 Roller Mouse User Guide
- June 17, 2024
- contour
Table of Contents
Pro3 Roller Mouse
RollerMouse Pro3
User Guide
Box Contents
- RollerMouse Pro3
- Two short keyboard risers
- Two long keyboard risers
RollerMouse Functions
A. Rollerbar
B. Cursor speed LED
C. Cursor speed adjustment
D. Copy
E. Paste
F. Left-click
G. Right-click
H. Scroll wheel
I. “One Touch” double-click
For additional mouse features and
specific Mac settings, please download our driver at
http://support.contourdesign.com
Keyboard Positioning
Before plugging in the unit, take a moment to check the height and angle of
your keyboard, and find the arrangement that’s most comfortable for you. Use
the risers to achieve the correct angle and height regardless of the type of
keyboard you are using. The spacebar on your keyboard should come just above
your rollerbar. To achieve a proper ergonomic position, the front edge of the
keyboard should be as close as possible to the rollerbar.
Balance Keyboard is designed specifically for the RollerMouse.
The keyboard sits level with the rollerbar and can be easily adjusted to a
positive, neutral, or negative tilt.
Inserting the Keyboard Risers
Fit the end of the riser 2 into the slot on the back of the RollerMouse Pro3.
Adjusting Risers
Line up the short and long risers 2 and 3 then press the two parts together
until you hear them snap into place.
Connecting to a computer
Plug the RollerMouse Pro3 USB cable into the computer’s USB port.
Allow your computer a few seconds to automatically install. 
Click Force Tension Adjustment
For optimal control, you can adjust the amount of pressure required to perform
a mouse click. Use the click force tension slider located under your
RollerMouse Pro3. Simply slide it until you find the click control that works
best for you.
Using the rollerbar
The rollerbar A provides two functions:
- Pressing down on the rollerbar performs a left click.
- Moving the rollerbar from side to side and up and down performs cursor movement.
Change cursor speed
Press the Cursor Speed button C to cycle through cursor speeds. There are ten
speed selections which range from slow (600 DPI) to fast (2400 DPI).
Speed can be identified by the LED lights as shown. User settings
RollerMouse Pro3 has 3 modes. PC-mode, Mac-mode and Linux (HID-mode).
The default setting on your RollerMouse, is PC-Mode. Use the following key
commands to switch settings to best fit your operating system.
- Press and hold the C and D buttons simultaneously for two seconds to see the LED lights flash for the respective mode.
- While holding the C button, release the D button and click on the D button to toggle though the different modes.
- Release both buttons once the desired mode has been reached.
Different Mode Settings
| PC-Mode | MAC-Mode | Linux (HID) |
|---|---|---|
| LED’s light up from left to right | LED’s light up from right to left | LED’s |
light up from both sides towards the middle
For illustrated information on these modes please visit support.contourdesign.com
Changing the ‘Double click’ button to ‘Middle’ function
To change double click button I to function as a middle click, hold buttons C
and I for two seconds until LED lights flash to confirm.
Repeating this process will revert back to double click functionality.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.
Warranty
If there is a functional defect due to faulty manufacturing, we will replace
the product. This warranty does not cover damage that results from misuse of
the product.
Attention!
If you attempt to dismantle your RollerMouse, you will invalidate your
warranty.
For more information please visit:
www.contourdesign.com
Contour Design, Inc.
10 Industrial Drive
Windham, New Hampshire 03087, USA
Phone: 603-893-4556
Email: ergoinfo@contourdesign.com
Contour Design Nordic A/S
International House
Center Boulevard 5
2300 Copenhagen S. Denmark
Phone: +45 32 46 11 20
Email: info@contour-design.com
Kingsbury House
468 Church Lane
London, NW9 8UA, United Kingdom
Phone: +45 70 27 02 27
Email: info@contour-design.com
Tested to comply with FCC and IC standards
References
- Logo, Graphic & AI Design | Design.com
- Manual-Hub.com - Free PDF manuals!
- Find support to all Contour Design products
- Contour Design – Ergonomic mice, Superior design
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>