CROSLEY CF3001 Kitchen Cart

PART LIST

HARDWARE LIST

ADDITIONAL TOOLS (Not Provided)

Note:
It is not recommended to use power tools during assembly.

Note:
Wood dowels are intended for alignment. Additional clearance between the wood dowel and the pre-drilled hole is intentional for ease of assembly.

Installation

Step 1
Insert cam bolts (part #2) into the top panel (part A), left panel (part B), right panel (part C), towel bar left panel (part X) and towel bar right panel (part Y) using phillips head screwdriver.

NOTE:
Do not overtighten cam bolts. Stop tightening once threads on the cam bolt are no longer visible.

Step 2
Attach knobs (part #8) to drawer front panels (part Q), left door panels (part V) and right door panels (part W) using round head bolts (part #9) and phillips head screwdriver. Attach the drawer left panel (part R) and drawer right panel (part S) to the drawer front panel (part Q) using screws (part #5) and a phillips head screwdriver. Slide the drawer bottom panel (part U) into the grooves of assembled unit (parts Q, R & S). Attach the drawer back panel (part T) to assembled unit (parts R, S & U) using screws (part #5) and phillips head screwdriver. Repeat for the remaining drawer.

NOTE: Be sure drawer glide wheels are facing the back panel.

Step 3
Attach the front top rail (part E) to the top vertical panel (part L) using a wood dowel (part #3), long screw (part #15) and phillips head screwdriver. With the front top rail (part E) flat on the ground, attach the front middle rail (part G) and back top rail (part F) to the top vertical panel (part L) using wood dowels (part #3), long screws (part #15) and phillips head screwdriver.

NOTE:
Please ensure screws are aligned with the pre-drilled holes in the top vertical panel (part L) before tightening.

Step 4
Attach assembled unit (parts E, F, G & L) to right panel (part C) using wood dowels (part #3) and cam locks (part #1 ). Attach the back top panel (part D) to the right panel (part C) using a wood dowel (part #3) and cam locks (part

1 ).

NOTE:
Cam locks must rotate a full 180°. See the pictured insert.

Step 5
Attach back partition panels (part M) to the back top panel (part D) using wood dowels (part #3). Slide back panels (part N) into grooves of the right panel (part C), back top panel (part D) and back partition panels (part M).

Step 6
Attach back bottom rail (part H) to back partition panels (part M), back panels (part N) and right panel (part C) using wood dowels (part #3) and cam lock (part #1 ).

NOTE:
Cam locks must rotate a full 180°. See the pictured insert.

Step 7
Attach the left panel (part B) to the assembled unit (parts D, E, F, G, H & N) using wood dowels (part #3) and cam locks (part #1 ).

NOTE:
Cam locks must rotate a full 180°. See the pictured insert.

Step 8
Attach double magnet (part #11) and magnets (part #12) to front middle rail (part G) using round head screws (part #13) and phillips head screwdriver. Attach left partition panel (part J) and right partition panel (part K) to back top rail (part F) and front middle rail (part G) using wood dowels (part

3).

Step 9
Attach bottom panel (part I) to assembled unit (parts B, C, H, J & K) using wood dowels (part #3), long bolts (part #4), barrel nuts (part #6) and Allen wrench (part #14).

Step 10. CASTER INSTALLATION
Attach locking casters (part ZE) and casters (part ZF) to the bottom panel (part I) using large round head screws (part #10) and phillips head screwdriver.

NOTE:
LEG INSTALLATION – Do not install casters. Attach legs using the instruction manual and hardware included inside leg packaging.

Step 11
Insert the towel bar (part ZB) and support bars (part Z) into the towel bar left panel (part X). Attach the support panel (part ZA) to the towel bar left panel (part X) using wood dowels (part #3) and cam lock (part #1 ). Attach towel bar right panel (part Y) to assembled unit (parts Z, ZA & ZB) using wood dowels (part #3) and cam lock (part #1 ).

NOTE:
Cam locks must rotate a full 180°. See the pictured insert.

Step 12
Carefully turn the unit upright. Secure the left partition panel (part J) and right partition panel (part K) to the back top rail (part F) and front middle rail (part G) using long screws (part #15) and phillips head screwdriver. Attach the assembled unit (parts X, Y, Z, ZA & ZB) to the left panel (part B) using long bolts (part #4) and wood dowels (part #3). Attach small towel bar panels (part ZC) to the right panel (part C) using long bolts (part #4) and wood dowels (part #3). Insert a small towel bar (part ZD) through the holes of small towel bar panels (part ZC).

NOTE:
Bolts will be inserted from the inside of the unit.

Step 13
Attach the top panel (part A) to the assembled unit (parts B, C, D, E & L) using wood dowels (part #3) and cam locks (part #1 ).

NOTE:
Cam locks must rotate a full 180°. See the pictured insert.

Step 14
Attach left door panels (part V) and right door panels (part W) by placing the bottom pin hinge (pre-installed in the door) in the pre-drilled hole of the bottom panel (part I). Then depress the top spring-loaded pin hinge so it can be placed in the pre-drilled hole of the front middle rail (part G). Place shelf holders (part #7) into the desired position.

NOTE:
Be sure the top and bottom pin hinges are fully extended to secure doors in place.

Step 15
Slide assembled drawers into place. Slide adjustable shelves (part 0) and middle adjustable shelf (part P) into place.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>