D A S ACTION 12 Passive Full Range User Manual
- June 17, 2024
- D A S
Table of Contents
User Manual
action series
Before operating the device, please read the “Safety precautions” section of
this manual.
Retain this manual for future reference.
Safety Precautions
Passive loudspeaker enclosures
Keep these instructions.
Heed all warnings. Follow all instructions.
The exclamation point inside an equilateral triangle indicates the existence
of internal components whose substitution may affect safety.
The double square indicates Class II device.
The specifications can be found on the rear label of the product.
The appliance should be flown only from the rigging points and by qualified
personnel. Do not suspend the box from the handles.
Do not expose this device to rain or moisture. Do not place any objects
containing liquids, such as bottles or glasses, on the top of the unit. Do not
splash liquids on the unit. IP-20 equipment.
This symbol on the product indicates that this product should not be treated
as household waste. Instead it shall be handed over to the appicable
collection point for the recycling of electrical and electronic equipment.
Working temperature ranges from 15ºC to 35ºC with a relative humidity of 75%.
The outer wiring connected to the device requires installation by an
instructed person or the use of a flexible cable already prepared.
Note that the two Speak on input connectors are wired in parallel to provide
easy parallel connection of several enclosures.
Do not place loudspeakers in proximity to devices sensitive to magnetic fields
such as television monitors or data storage magnetic material.
For enclosures with tripod socket, the maximum safety height from floor to bottom of enclosure when mounting on a TRD-2 tripod, with legs spread 55cm from the central pole, is:
action-8- ————->125 cm
action-12 ————->115 cm
action-15 ————->105 cm
No user serviceable parts inside. Refer all servicing to qualified service
personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally or has been dropped.
Clean only with a dry cloth. Do not use any solvent based cleaners.
WARRANTY
All D.A.S. products are warrantied against any manufacturing defect for a
period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory or any of
its authorised service centers.
To claim a warranty repair, do not open or intend to repair the product.
Return the damaged unit, at shippers risk and freight prepaid, to the nearest
service center with a copy of the purchase invoice.
DECLARATION OF CONFORMITY
D.A.S. Audio, S.A.
Declares that passive action series:
Abide by essential objectives relating Directives:
- Directiva de Baja Tensión (Low Voltage Directive) 2014/35/UE
- Directiva RoHS 2011/65/UE
- Directiva RAEE (WEEE) 2012/19/UE
In accordance with Harmonized European Norms:
- EN 60065:2014.- Audio, video and similar electronic apparatus. Safety requirements.
- EN 50581:2012.- Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances.
INTRODUCTION
The action series inherits the exceptional sound quality and rugged build that
have made D.A.S.
professional systems an internacional sound reinforcement standard. Designed
from “real-world” experience, they offer users outstanding performance,
absolute reliability, and unparalleled convenience. Whether it is in a high-
profile venue or on the stage of a major event, the action series will provide
the power and definition needed to make your performance a success.
Features
action 8
- 2-way, full-range system
- 8″ bass loudspeaker
- Compression driver
- Asymmetric enclosure design for stage monitor use
- Built-in rigging points
- Stand mountable
The action 8 is a compact 2-way passive full-range loudspeaker that utilizes a 8” low frequency transducer and a full compression driver. The multi-angle cabinet is constructed of Birch plywood protected by an enviormentally friendly ISO-flex black paint finish. A rear located handle and a robust steel grille are provided. A 35 mm tripod socket allows for stand mounting.
action 12
- Two-way full-range system
- 12″ bass loudspeaker
- Compression driver with titanium diaphragm
- Asymmetric enclosure design for stage monitor use
- Built-in rigging points (eyebolt based)
- Stand mountable
The action 12 is a 2-way passive full-range loudspeaker that utilizes a 12” low frequency transducer and a 1” exit compression driver. The multi-angle cabinet is constructed of Birch plywood protected by an environmentally friendly black paint finish. Two bar handles and a steel grille are provided. A 35mm tripod socket allows for stand mounting.
action M12
- Dedicated stage monitor
- 12″ bass loudspeaker
- Compression driver with titanium diaphragm
- Low profile enclosure design for minimum visual impact
- Black paint finish
- Stand mountable
The action M12 is a dedicated stage monitor designed for use with external amplification. The enclosure is constructed from Birch plywood and is protected with a black paint finish. Two side located handles facilitate handling and a steel grille protects the components. A pole mount socket adds versatility to the action M12.
action 15
- Two-way, full-range system
- 15″ bass loudspeaker
- Compression driver with titanium diaphragm
- Asymmetric enclosure design for stage monitor use
- Built-in rigging points (eyebolt based)
- Stand mountable
This 2-way passive full-range loudspeaker utilizes a 15” low frequency transducer and a 1” exit compression driver with titanium diaphragm. The cabinet is constructed of Birch plywood and finished with an environmentally friendly black paint finish. Two bar handles are provided and a steel grille protects components. A 35 mm tripod socket allows for stand mounting. Rigging points provide a safe and simple solution for suspending the action 15.
action 215
- 2-way, full-range system
- 2 x 15″ bass loudspeaker
- Compression driver with titanium diaphragm
- Two steel-reinforced handles
The action 215 is a 2-way passive full range loudspeaker utilizes two 15” bass
loudspeakers for extra low frequency punch and higher SPL.
High frequencies are handled by a 1” compression driver with titanium
diaphragm. The trapezoidal cabinet is constructed using Birch plywood and
protected with a hard-wearing black paint finish. Two bar handles and a steel
grille sealed against corrosion using a polyamide powder coat finish are
provided. Rigging points provide a safe and simple way to fly the action 215
cabinets.
action 18
- Bass-reflex subwoofer system
- 18″ low frequency transducer
- Precise and powerful bass reproduction
- Top located pole mount socket
The action 18 bass system incorporates a 18” low frequency transducer with a 4 ” voice coil mounted as a direct radiator into a bass reflex cabinet. The loudspeaker is protected by a perforated steel grille, sealed against corrosion using a powder coat finish. The action 18 is designed for use in beamed systems. A top located pole-mount socket permits mounting full-range systems above the action 18 and two bar handles makes moving easy.
action 218
- High output bass-reflex subwoofer system
- Twin 18″ loudspeakers
- Durable black paint finish
- Side located bar handles
This high power bass-reflex subwoofer system uses dual 18″ bass loudspeakers equipped with 4″ voice coils. The exceptional power handling capacity and efficiency provide high sound pressure levels of powerful bass. Two hand locations facilitate handling. The cabinet is designed to be stacked in the vertical position in order to reduce the units “on-stage” footprint.
CONFIGURATIONS
RIGGING
Warnings
This manual contains needed information for flying D.A.S. Audio line array
systems, description of the elements and safety precautions. To perform any
operations related to flying the system, read the present document first, and
act on the warnings and advice given. The goal is to allow the user to become
familiar with the mechanical elements required to fly the acoustic system, as
well as the safety measures to be taken during set-up and teardown.
Only experienced installers with adequate knowledge of the equipment and local
safety regulations should fly speaker boxes. It is the user’s responsibility
to ensure that the systems to be flown (including flying accessories) comply
with
state and local regulations.
The working load limits in this manual are the results of tests by independent
laboratories. It is the user’s responsibility to stay within safe limits. It
is the user’s responsibility to follow and comply with safety factors,
resistance values, periodical supervisions and warnings given in this manual.
Product improvement by means of research and development is on going at D.A.S.
Specifications are subject to change without notice.
To this date, there is no international standard regarding the flying of
acoustic systems. However, it is common practice to apply 5:1 safety factors
for enclosures and static elements. For slings and elements exposed to
material fatigue due to friction and load variation the following ratios must
be met; 5:1 for steel cable slings, 4:1 for steel chain slings and 7:1
polyester slings. Thus, an element with a breaking load limit of 1000 kg may
be statically loaded with 200 kg (5:1 safety factor) and dynamically loaded
with 142 kg (7:1 safety factor).
When flying a system, the working load must be lower than the resistance of
each individual flying point in the enclosure, as well as each box.
Hanging hardware should be regularly inspected and suspect units replaced if
in doubt. This is important to avoid injury and absolutely no risks should be
taken in this respect. It is highly recommended that you implement an
inspection
and maintenance program on flying elements, including reports to be filled out
by the personnel that will carry out the inspections. Local regulations may
exist that, in case of accident, may require you to present evidence of
inspection reports and corrective actions after defects were found.
Absolutely no risks should be taken with regards to public safety. When flying
enclosures from ceiling support structures, extreme care should be taken to
assure the load bearing capabilities of the structures so that the
installation is absolutely safe. Do not fly enclosures from unsafe structures.
Consult a certified professional if needed. All flying accessories that are
not supplied by D.A.S. Audio are the user’s responsibility. Use at your own
risk.
Introduction
Flyable action series models feature 6 internal steel angles, with 2 mounting
threads each, so that 12 flying points are available (2 on each side, 3 on the
top panel and 3 on the bottom panel and 2 on the rear panel). Eyebolt flying
points are factory sealed with M10 screws, which are replaced with eyebolts on
the flying points as required. Flying with eyebolts is very economical and
safe, and is specially recommended for fixed installations where the boxes are
permanently
fixed. The illustration shows the internal metal hardware of an enclosure with
eyebolt flying.
Flying with eyebolts
The Allen-head screws must be removed and replaced by M10 eyebolts on one side
of the enclosure. Each rigging point has 200 kg (440 lb) working load limit.
Then choose the slings or chains of required load resistance and length,
bearing in mind that the length difference between the front and back slings
or chains will determine the vertical orientation. Alternatively, the back
bottom eyebolt points can be used to provide vertical orientation.
The ANL-2 set is an optional set of three eyebolts and three carabiners.
(Dimensions are in milimetres).
Each ANL-2 eyebolt has a rated working load of 200 kg. (440 lb). Each ANL-2
carabiner has a working load of 330 kg (726 lb). If using other hardware, make
sure it is rated to handle the required load.
When using eyebolts it is important to bear in mind that the rated working
load is only true for a load applied in the plane of the eye, and is
significantly reduced for other angles. The drawing illustrates the concept.
The table shows the variation of the working load as a function of the load
angle. In the case of the ANL-2 eyebolt, this means that the 200 kg working
load becomes 60 kg at 45 degrees. Do not use eyebolt flying if the load angle
is higher than 45 degrees.
| 0 Degrees| 30 Degrees| 45 Degrees| More than 45
Degrees
---|---|---|---|---
% Working
load| 100%| 65%| 30%| 25%
The following illustrations show different views on eyebolt flying for a single box. The length of the back cables or chains determines the vertical angle of the box.
Instructions for AXU-AC8 (only Action8)
Introduction
The AXU series are designed for enclosures Action-8, Action-8A, and different
versions.
Safety Precautions
Wall plugs provided are to be used in brick walls only.
For other wall materials, source the suitable wall plug before use.
D.A.S. Audio is not responsible for use other than the recommended or whether
it be the result of insufficient strength of the support structure. Use only
the screws and wall plugs supplied on surfaces that will provide sufficient
support. Do not use on surfaces such as plaster, and gypsum. It is highly
recommended and in most parts of the world mandatory, that a safety cable be
used to secure the enclosure to the structure.
To ensure optimum safety, the installation should be checked thoroughly at
regular intervals replacing all deteriorated elements.
Loosen the screws before reorienting the speaker.
Never force the rigging elements.
Contact a licensed rigger if there is any doubt.
Mounting instructions
You can consult the AXU-AC8 mounting instructions for enclosures Action 8A on the web: www.dasaudio.com
LINE DRAWINGS
ALL DIMENSIONS IN MILIMETERS
SPECIFICATIONS
Model | action 8 | action M12 | action 12 |
---|---|---|---|
Peak Power Handling (-10 dB) | 600 W | 1200 W | 1200 W |
RMS Power Handling (1) | 150 W | 300 W | 300 W |
Frequency Range (-10 dB) | 60 Hz – 20kHz | 63 Hz – 20kHz | 50 Hz – 20kHz |
HF Horn Coverage Angles(-6dB) | 80º x 80º | 80º x 50º | 80º x 50º |
On-axis Sensitivity 1 W / 1m | 92 dB SPL | 95 dB SPL | 96 dB SPL |
Rated Maximum Peak SPL (2) | 120 dB | 130 dB | 131 dB |
Nominal Impedance | 8 ohms | 8 ohms | 8 ohms |
Transducers/Replacement Parts | LF: 8B / 8B | ||
HF: M-26 / GM M-26 | LF: 12Mi / GM 12Mi | ||
HF: M-34 / GM M-34 | LF: 12Mi / GM 12Mi |
HF: M-34 / GM M-34
Enclosure Material| Birch Plywood| Birch Plywood| Birch Plywood
Color/Finish| Black Paint| Black Paint| Black Paint
Connectors| 2 x NL4 Speakon| 2 x NL4 Speakon| 2 x NL4 Speakon
Dimensions (H x W x D)| 47.5 x 27.9 x 25.5 cm
18.7 x 11 x 10 in| 42 x 64.5 x 31.6 cm
16.6 x 25.4 x 12.5 in| 65.3 x 37.8 x 32.4 cm
25.7 x 14.9 x 12.8 in
Weight| 8.4 kg (18.5 lb)| 17.5 kg (38.5 lb)| 18.5 kg (40.7 lb)
Accessories| AXW-1, TRD-2, TRD-6| TRD-2, TRD-6| ANL-2, TRD-2, TRD-6
Model| action 15| action 215| action 18| action 218
---|---|---|---|---
Peak Power Handling (-10 dB)| 1400 W| 2800 W| 2400 W| 4800 W
RMS Power Handling (1)| 350 W| 80º x 50º| 600 W| 1200 W
Frequency Range (-10 dB)| 47 Hz – 20kHz| 47 Hz – 20kHz| 33 Hz – 160 Hz| 29 Hz
– 160 Hz
HF Horn Coverage Angles(-6dB)| 80º x 50º| 700 W| |
On-axis Sensitivity 1 W / 1m| 96 dB SPL| 99 dB SPL| 96 dB SPL| 99 dB SPL
Rated Maximum Peak SPL (2)| 131 dB| 134 dB| 133 dB| 139 dB
Nominal Impedance| 8 ohms| 4 ohms| 8 ohms| 4 ohms
Transducers/Replacement Parts| 24.5 kg (53.9 lb)
ANL-2, TRD-2, TRD-6| LF: 2 x 15Mi / GM 15Mi
HF: M-44 / GM M-44| LF: 18H / GM 18G| LF: 2 x 18H / GM 18G
Enclosure Material| Birch Plywood| Birch Plywood| Birch Plywood| Birch Plywood
Color/Finish| Black Paint| Black Paint| Black Paint| Black Paint
Connectors| 2 x NL4 Speakon| 2 x NL4 Speakon| 2 x NL4 Speakon| 2 x NL4 Speakon
Dimensions (H x W x D)| 77.4 x 44.6 x 43.6 cm
30.5 x 17.6 x 17.2 in| 115.4 x 44.7 x 47.4 cm
45.5 x 17.6 x 18.7 in| 62.4 x 54 x 65 cm
24.6 x 21.3 x 25.6 in| 106.7 x 54 x 67 cm
42 x 21.3 x 26.4 in
Weight| 24.5 kg (53.9 lb)| 38.5 kg (83.6 lb)| 34.5 kg (75.9 lb)| 61 kg (134.2
lb)
Accessories| ANL-2, TRD-2, TRD-6| ANL-2| TRD-6| TRD-6
(1) Based on a 2 hour test continuosly applying 6 dB crest factor pink noise
(IEC shaped).
UM_ACT_03_EN
D.A.S. AUDIO, S.A.
C/. Islas Baleares, 24
46988 Fuente del Jarro
Valencia, SPAIN
Tel. 96 134 0525
Tel. Intl. +34 96 134 0860
Fax 96 134 0607
Fax Intl. +34 96 134 0607| D.A.S. AUDIO OF AMERICA, INC.
Sunset Palmetto Park
6816 NW 77th Court.
Miami, FL. 33166 – U.S.A.
TOLL FREE: 1-888DAS4USA
Tel. +1 305 436 0521
Fax +1 305 436 0528| D.A.S. AUDIO ASIA PTE. LTD.
25 Kaki Bukit Crescent #01-00/02-00
Kaki Bukit Techpark 1
Singapore 416256
Tel. +65 6742 0151
Fax +65 6742 0157
---|---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>