Dimplex DF3015 Electric Fireplace Owner’s Manual

Dimplex DF3015 Electric Fireplace

Product Information

Specifications

• Model: DF3015
• Manufacturer: Dimplex
• Power Source: Electric
• Usage: Indoor

FAQ

• Q: Can I use this fireplace outdoors?
  • A: No, the fireplace is not intended for outdoor use.
• Q: Can I use this fireplace in a bathroom or laundry area?
  • A: No, the fireplace is not intended for use in bathrooms, laundry areas, and similar indoor locations.
• Q: How do I contact customer support?
  • A: You can contact customer support through the website at www.dimplex.com/customer_support or by calling the toll-free number 1-888-DIMPLEX (1-888-346-7539) during operating hours (Monday to Friday 8:00 a.m. to 4:30 p.m. EST).

IMPORTANT SAFETY INFORMATION

Always read this manual first before attempting to install or use this fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit www.dimplex.com

Always use a qualified technician or service agency to repair this fireplace.

NOTE: Procedures and techniques that are considered important enough to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
Warning: Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death.

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex, the world leader in electric fireplaces.
Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty.

Please record your model and serial numbers below for future reference: model and serial numbers can be found on the Model and Serial Number Label of your fireplace.

STOP: NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?

• Contact us at: www.dimplex.com/customer_support
• For Troubleshooting and Technical Support
• Toll-Free: 1-888-DIMPLEX (1-888-346-7539)
• Monday to Friday 8:00 a.m. to 4:30 p.m. EST
• Please have your model number and product serial number ready. (See above)

Important Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this appliance.
2. The heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the unit.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the unit is left operating and unattended.
4. Always unplug the fireplace when not in use.
5. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned, or if the fireplace has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment or repair.
6. Do not use outdoors.
7. The fireplace is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
8. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area and where it will not be tripped over.
9. To disconnect the unit, turn the controls off, then remove the plug from the outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage to the heater.
    • CAUTION: RISK OF ELECTRIC SHOCK
    • DO NO T OPEN
    • NO US ER-SERVICEABLE PARTS INSIDE
11. To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
12. All electrical heaters have hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to flammable vapours.
13. Do not modify the fireplace. Use it only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.
14. Avoid the use of an extension cord. Extension cords may overheat and cause a risk of fire. If you must use an extension cord, the cord must be No. 14 AWG minimum size and rated no less than 1875 Watts.
15. Do not burn wood or other materials in the fireplace.
16. Do not strike the fireplace glass.
17. Always use a certified electrician should new circuits or outlets be required.
18. Always use properly grounded, fused and polarized outlets.
19. Disconnect all power supply before performing any cleaning, maintenance or relocation of the unit.
20. When transporting or storing the unit and cord, keep in a dry place, free from excessive vibration and store so as to avoid damage.

SAVE THESE INSTRUCTIONS

FCC STATEMENT

CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

WARNING: Remote control contains small batteries. Keep away from children. If swallowed, seek medical attention immediately.
WARNING: Do not install battery backwards, charge, put in fire or mix with used or other battery types – may explode or leak causing injury.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.

Quick Reference Guide

1. The information regarding the model of your electric fireplace can be found on the label located on the back of the unit.
2. If you have any technical questions or concerns regarding the operation of your electric fireplace, or require service contact customer service.
3. The heater on your fireplace may emit a slight, harmless odor when first used. This odor is a normal condition caused by the initial heating of internal heater parts.

Site Selection and Preparation

This section provides instructions for selecting a location and preparing the site to install the fireplace into your Dimplex mantel surround.

1. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic.
2. For ease of electrical hook up you may wish to locate the fireplace near an existing outlet (refer to NO TE 1).
3. Store the fireplace in a safe dry and dust free location.

NOTE 1 : A 15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred but not essential in all cases.

A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.

WARNING: Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician.

NOTE: The dimensions of the fireplace are 30 ¼ inches (768 mm) wide x 25 ½ inches (648 mm) high x 10 ½ inches (267 mm) deep. The viewing area is 30 ⅛ inches (765 mm) wide and 20 ⅛ inches (511 mm) high. The fireplace does not require any additional venting. (See Figure 1 for recommended installation clearances.)

Fireplace Installation

Install the fireplace assembly into the mantel (refer to mantel assembly instructions).

NOTE 1: A 15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.

IMPORTANT

• If not using a Dimplex mantel, the fireplace must be installed in an enclosure with the following MINIMUM internal/opening dimensions (Figure 1A).

New Wall Construction

1. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic.
2. Place the fireplace in the desired location to see how it will look in the room.
3. Mark the desired location on the floor and store the fireplace in a safe, dry and dust free location.
4. Use studs to frame an opening of 30 ½ inches (775 mm) wide x 25 ¾ (654 mm) inches high x 11 ¾ inches (298) deep. (Figure 1B)

Option #1: The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace.
Option #2: A new outlet can be installed inside the new frame construction.

Plug the unit into a 15 Amp/120 Volt outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1875 Watts.

CAUTION: Clearance for air circulation beneath the fireplace insert is provided by six (6) rubber feet. Do not install the fireplace insert directly on carpet or similar surfaces which may restrict air circulation. If installing the fireplace in a carpeted area, place a one-piece, solid, flat surface under the fireplace insert. Ensure that all six of the insert’s feet rest securely on this surface.

Operation

Electric Fireplace Manual Controls

• The manual controls for the fireplace are located in the lower right hand corner (Figure 2).

Main On/Off Switch

• Supplies power to the Three Position Manual Control Switch.

Three Position Manual Control Switch

• Remote (right position): The unit is operated with the remote control.
• Flame (center position): The flame effect is turned on.
• Flame & Heat (left position): The flame effect and heater are turned on simultaneously. When the manual control is in the Flame & Heat position the heater does not run on the remote operated thermostat.

NOTE

• When the manual control switch is in the Flame and Flame & Heat positions, the fireplace unit will not operate with the remote control.

Initialization Button

• Used to synchronize the supplied remote control with the fireplace.

Resetting The Temperature Cutoff Switch

• Should the heater overheat, an automatic switch will turn the heater off and it will not come back on without being reset.
• The temperature cutoff switch can be reset by unplugging the unit, waiting five (5) minutes and plugging the unit back in.

CAUTION: If you need to continuously reset the heater, unplug the unit and call Dimplex North America Limited at 1-888-346-7539. Please have your model and serial number ready when calling.

Remote Control

The remote control has a range of approximately 50 feet (15.25 m), it does not have to be pointed at the fireplace and can pass through most obstacles (including walls). It is supplied with 243 independent frequencies to prevent interference with other units.

Battery Installation

1. Depress tab on the battery cover on the back of the remote transmitter and remove battery cover.
2. Install two (2) AAA batteries into the remote control (included).
3. Ensure Child Lock is in the “unlocked” position (Figure 3).
4. Replace the battery cover.
   • NOTE: When the “BAT” symbol is present on the remote control it is recommended to replace the batteries promptly, to maintain full functionality of the remote/fireplace. The remote transmitter has a battery backup time of only several hours.
   • Battery must be recycled or disposed of properly. Check with your Local Authority or Retailer for recycling advice in your area.

Remote Control Initialization/ Reprogramming

1. Plug cord into a 120 Volt wall outlet.
2. Ensure the Main On/Off Switch located in the switch box on the fireplace in the lower right hand corner is in the On – position.
3. Set the Three Position Manual Control (Figure 2B) to the Remote position (right position).
4. Press and hold the Initialization Button on the unit (Figure 2C).
5. While holding the Initialization Button, press the Flame/ Heat On/Off button or the Purifire™ On/Off button on the remote control transmitter.
6. Release the Initialization Button on the unit.
7. Press the Flame/Heat On/ Off button to turn the Flame/ Heat function on or press the Purifire™ On/Off button to turn the Purifire™ function on.

Remote Control Functions

(All letter references are to Figure 4)

• B. Set Temperature
  • Press H button to turn fireplace on. Press J to raise thermostat, or I to lower the thermostat. Press both J and I to change °F to °C.
• C. Light Dimmer Control
  • While the fireplace is running, repeatedly press the L or K button to increase or decrease the brightness of the upper lights.
• D. Flame Speed Control
  • While the fireplace is running, press the N button to increase the speed of the flame or press the M to decrease the speed of the flame.
• E. Sleep Timer
  • The Sleep Timer automatically shuts off the fireplace after a preset time (from 30 minutes to 8 hours). During fireplace operation, to set the sleep timer press the P button. Set the timer from 30 minutes through 8 hours. The fireplace will automatically turn off when the sleep timer reaches zero (0) minutes. The sleep timer can be cancelled at any time by pressing the O button repeatedly until the sleep timer displays nothing.
• F. Purifire™
  • The Purifire™ includes a high efficiency filter to help improve the quality of air. Press the G button to turn the Purifire™ function on. When the Purifire™ function is on, the Purifire™ symbol will flash. When off, the symbol will be solid. The default setting for the Purifire™ is set at low speed. Press the Q or the R buttons to change between low and high speeds. Press the G button to turn the Purifire™ function off.
• H. Flame & Heat On/Off Button
  • Press the H button to turn the Flame/Heat function on. When B is higher then A the heat will come on. To turn the heat off, lower the B so that it’s setting is lower then the A. The default temperature setting is 72°F (22°C).

NOTE

• When using the remote control the heater runs on a thermostat. Press the J or I buttons to adjust the set temperature. Once the desired set temperature is reached the heater will turn off.
• The heater will cycle On and Off to maintain the desired set temperature.

Child Lock (Figure 5)

1. Depress tab on the battery cover on the back of the remote transmitter and remove the battery cover.
2. Move Child Lock tab to the right to lock the remote transmitter.
3. Move Child Lock tab back to the left to unlock the remote transmitter.
4. Replace the battery cover.

NOTE: To temporarily unlock the remote transmitter press (in order) I then J then K.

When the remote transmitter’s backlight is illuminated the Child Lock is bypassed. When the backlight is off the Child Lock is re-activated.

Frequency Interference

If the fireplace does not respond properly to the remote control, the remote operating frequency may have to be reset. The remote control can send another frequency code to the circuit board to eliminate interference.

1. Simultaneously press the O button and the Q button on the remote control.
2. “COD” will appear in place of the sleep timer digits.
3. Release the O button and the Q button.
4. Press the Initialization button on the unit (Figure 2C).
5. Press the H button on the remote.

Your remote will now have a different frequency communicating with the fireplace.

Maintenance

WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. Light Bulb Replacement

CAUTION: Allow at least five (5) minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin.

Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log ember bed exterior disappears. There are three (3) bulbs under the log set assembly which generate the flames and embers, and two (2) bulbs above that illuminate the log exterior.

Helpful Hints

• It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life.
• Group replacement will reduce the number of times you need to open the unit to replace light bulbs. Care must be taken when removing the log set as the log set contains LED’s and wires.

Lower Light Bulb Requirements

• Quantity of three (3) clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 Watt rating. Example: GE 60BC or Philips 60CTC.

Do not exceed 60 Watts per bulb

To access the lower light bulb area:

1. Slide fireplace out of mantel.
2. Remove four (4) Phillips screws from right side of trim (Figure 6).
3. Remove trim.
4. Slide glass to right side of fireplace to remove (Figure 6).
5. Pull the front edge of the plastic Log Set or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the mirror (Figure 7).
   • IMPORTANT: Only handle the Log Set Assembly by the Ember Bed or plastic grate.
   • NOTE: Log Set Assembly fits tightly into firebox, some force may be necessary to remove.
6. Set Log Set Assembly in front of fireplace.
7. Disconnect the Log Set Assembly’s LED wire harness from unit.
8. Unscrew bulbs counter clockwise.
9. Insert new bulbs and screw in clockwise.
10. Reconnect the LED wire harness.
11. Install the Log Set Assembly by placing the front, bottom edge of the Ember Bed in the track behind the control panel. Once in place, push down on the back edge of the Ember Bed until the rear tab snaps into place under the Mirror (Figure 7).
    • NOTE: Ensure the Log Set Assembly is installed tightly under the back ledge to prevent light leakage.
12. Slide front glass back into position and attach trim.

Upper Light Bulb Requirements

• Quantity of two (2) clear chandelier or candelabra bulbs with an E-12 (small) socket base, 15 Watt rating.

Do not exceed 15 Watts per bulb

To access the upper light bulb area:

1. Slide fireplace out of mantel.
2. Remove four (4) Phillips screws from right side of trim (Figure 6).
3. Remove trim.
4. Slide glass to the right side of the fireplace to remove (Figure 6).
5. Remove Upper Light Bracket (Figure 6).
6. Upper bulbs are located in the upper left and upper right corners of the fireplace.
7. Unscrew bulbs counter clockwise.
8. Insert new bulbs and screw in clockwise.
9. Re-install Upper Light Bracket.
10. Slide front glass back into position and attach trim.

Purifire™ Filter

The Purifire™ filter supplied in your fireplace is reusable and washable. The filter should be cleaned or replaced on average once a year. To clean the filter gently tap filter on a hard surface to dislodge any loose dirt or debris, and then clean with water. No soap or cleaning products are recommended. The filter size is 20 x 10 x 1 inches, rated at MERV 10.

To replace filter:

1. Remove fireplace from mantel.
2. Filter can be accessed from the top rear of the unit (Figure 8).
3. Grasp filter and slide filter straight up.
4. Replace or clean filter.

NOTE

• If after market air filter is used ensure it is installed according to the manufacturer’s recommended instructions.

Glass Cleaning

• The glass is cleaned in the factory during the assembly operation.
• During shipment, installation, handling, etc., the glass may collect dust particles; these can be removed by dusting lightly with a clean dry cloth.
• To remove fingerprints or other marks, the glass can be cleaned with a damp cloth. To prevent scratching, do not use abrasive cleaners or spray liquids on the glass surface.

Fireplace Surface Cleaning

• Use a cloth dampened with warm water only to clean painted surfaces of the electric fireplace.
• Do not use abrasive cleaners.

Warranty

Products to which this limited warranty applies

This limited warranty applies to the following model of your newly purchased Dimplex electric fireplace DF3015 and to newly purchased Dimplex fireplace surrounds (mantels) and trims. This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the US A (and the District of Columbia) except for Hawaii and Alaska. This limited warranty applies to the original purchaser of the product only and is not transferable.

Products excluded from this limited warranty

Light bulbs and Purifire™ filters are not covered by this limited warranty and are the sole responsibility of the owner/ purchaser. Products purchased in Yukon Territory, Nunavut, Northwest Territories, Hawaii, or Alaska are not covered by this limited warranty. Products purchased in these States, provinces, or territories are sold AS IS without warranty or condition of any kind (including, without limitation, any implied warranties or conditions of merchantability or fitness for a particular purpose) and the entire risk of as to the quality and performance of the products is with the purchaser, and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair.

What this limited warranty covers and for how long

Products, other than fireplace surrounds (mantels) and trims, covered by this limited warranty have been tested and inspected prior to shipment. Subject to the provisions of this warranty, Dimplex warrants such products to be free from defects in material and workmanship for a period of 5 years from the date of the first purchase of such products as follows:

(a) a repair or replacement warranty on defective products or parts, including in-home services, for the first 1 year following the date of first purchase; and (b) thereafter, a replacement of parts warranty on defective products and parts (with no in-home services) for the 4 year period commencing on the first anniversary of first purchase and ending on the fifth anniversary of the date of first purchase.

Dimplex fireplace surrounds (mantels) and trims covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Dimplex warrants such products to be free from defects in material and workmanship for a period of 1 year from the date of first purchase of such products. Warranty services do not include in-home services.

The above section is a summary only of your warranty rights. Please review the remaining provisions of this warranty for your specific rights.

The limited 5 year warranty period for products other than fireplace surrounds (mantels) and trims and the limited 1 year warranty period for fireplace surrounds (mantels) and trims also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to the purchaser.

What this limited warranty does not cover

This limited warranty does not apply to products that have been repaired (except by Dimplex or its authorized service representatives) or otherwise altered. This limited warranty does further not apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an incorrect power source.

What you must do to get service under this limited warranty

Defects must be brought to the attention of Dimplex Technical Service by contacting Dimplex at 1-888-DIMPLEX (1-888- 346-7539), or 1367 Industrial Road, Cambridge Ontario, Canada N1R 7G8. Please have proof of purchase, catalogue/ model and serial numbers available when calling. Limited warranty service requires a proof of purchase of the product.

What Dimplex will do in the event of a defect

In the event a product or part covered by this limited warranty is proven to be defective in material or workmanship during (i) the 5 year limited warranty period for products other than fireplace surrounds (mantels) and trims, and (ii) the 1 year limited warranty period for surrounds (mantels) and trims, you have the following rights:

• Limited warranty service will be performed solely by dealers or service agents of Dimplex authorized to provide limited warranty services.
• For products (other than surrounds (mantels) and trims) for the period ending at midnight on the first anniversary of the date of first purchase, Dimplex will in its sole discretion either repair or replace such defective product or part without charge. If Dimplex is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Dimplex may, in lieu of repair or replacement, choose to refund the purchase price for such product or part. This limited warranty entitles the purchaser to on-site or inhome warranty services. Accordingly, Dimplex will be responsible for all labour and transportation costs associated with the repair or replacement of the product or part except as follows: (i) charges may be levied for travel costs incurred to travel to the purchaser’s site where the product is located if the purchaser’s site is beyond 30 miles (48 km) from the closest service depot of Dimplex’s dealer or service agent; and (ii) the purchaser is solely responsible for providing clear access to all serviceable parts of the product.
• For products (other than surrounds (mantels) and trims) for the period commencing at 12:01 a.m. on the day after the first anniversary of the first purchase and ending at midnight on the fifth anniversary of the date of first purchase, this limited warranty entitles the purchaser to replacement parts only without charge. If Dimplex is unable to replace such part, or if replacement is not commercially practicable or cannot be timely made, Dimplex may, in lieu of replacement, choose to refund the purchase price for such part. The purchaser shall not be entitled to on-site or in-home warranty services. The purchaser shall be responsible for all expenses incurred for the removal of the part and installation of the replacement part including, without limitation, all shipping costs and transportation costs to and from the authorized dealer’s or service agent’s place of business and all labour costs. Such costs shall not be the responsibility of Dimplex.
• For surrounds (mantels) and trims for the period ending at midnight on the first anniversary of the date of first purchase, Dimplex will in its sole discretion either repair or replace such defective surrounds (mantels) and trims or part thereof without charge. If Dimplex is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Dimplex may, in lieu of repair or replacement, choose to refund the purchase price for such product or part. The purchaser shall not be entitled to on-site or in-house services. The purchaser is responsible for all expenses incurred for repair or replacement of such product or part including, without limitation, all shipping costs and transportation costs to and from the authorized dealer’s or service agent’s business and all labour costs. Such costs shall not be the responsibility of Dimplex.
• On-site or in-home services not provided under this warranty may be performed at the purchaser’s specific request and expense at Dimplex’s then-current rates for such services.

What Dimplex and its dealers and service agents are also not responsible for:

IN NO EVENT WILL DIMPLEX, OR ITS DIRECTORS, OFFICERS, OR AGENTS, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY, WHETHER IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT, EVEN IF DIMPLEX OR ITS DIRECTORS, OFFICERS, OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE FORESEEABLE. IN NO EVENT WILL DIMPLEX, OR ITS OFFICERS, DIRECTORS, OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES, COSTS, OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER.

How State and Provincial law apply

This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty.

Replacement Parts

• Log Set Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0439070100RP
• Flicker Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000240200KIT
• Heater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200490600RP
• Cutout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2300270300RP
• Main On/Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800070700RP
• Remote Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . 3000300300RP
• Cord Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4100040500RP
• Lower Light Wire Harness . . . . . . . . . . . . . . . . . . . . . . 2500400100RP
• Upper Light Wire Harness . . . . . . . . . . . . . . . . . . . . . . 2500400200RP
• Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5900680100RP
• Front Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5900310400RP
• Remote Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000890100RP
• Remote Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000880100RP
• Flicker Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5900080700RP
• Purifire™ Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0439060100RP
• Switch Housing Door. . . . . . . . . . . . . . . . . . . . . . . . . . 0439210200RP
• Wire Harness – 1 socket . . . . . . . . . . . . . . . . . . . . . . . . 2500150200RP
• Fireplace Foot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8800090100RP

Dimplex North America Limited

• 1367 Industrial Road
• Cambridge ON
• Canada N1R 7G8

© 2011 Dimplex North America Limited

www.dimplex.com

References

• Electric Fireplace & Heating Solutions | Dimplex
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>