Dasqua 8110 Heavy Duty Electronic Digital Caliper Instruction Manual

Dasqua 8110 Heavy Duty Electronic Digital Caliper

PRODUCT INSTRUCTIONS

STRUCTURES

1. Scale
2. Electronics
3. MM/IN: Metric/inch conversion
4. HOLD: Data hold button
5. Locking Screw
6. SET: Presetting button
7. Data output
8. Battery cover
9. Fine adjustment slider
10. Protective sticker
11. ZERO: Zero setting button
12. ABS/INC: Relative/absolute measurement
13. ON/OFF: Power on/off switch
14. External measuring faces
15. Internal measuring faces

INSTRUCTIONS

1. Operating Condition: Temperature: 5-40°C Relative Humidity;S80% Prevent any liquid from contacting the protective sticker
2. Never apply voltage(e.g. Engraving with an electrograph) on any part of the caliper for fear of damaging the circuit.
3. Preset a starting point of measurement correctly(please refer to OPERATION). Unless presetting, do not press the “SET” button purposely for fear of measurement error.

TECHNICAL SPECIFICATIONS

Accuracy

| 0-300mm: +/-0.04mm

0-500mm: +/-0.05mm

0-1000mm: +/-0.07mm

|

Battery life

|

approx.1 year

INSTRUCTIONS OF DATA OUTPUT

1. Preset zero and metric/inch system
2. Connect the end of the interface cable to the computer. The other to the data output port of the caliper.
3. Start the caliper and software.
4. Move the slider to the position you want and press the button on the control box for data output.

OPERATION

1. ON/OFF button
2. Press the ON/OFF button at any position when the power is off, and the caliper will be ready to work and display the measuring value.
3. Press ON/OFF at any position when the power is on, and the caliper will stop working.
4. ABS/INC button
5. Press the ABS button in absolute mode (without “ABS”), and the caliper is ready for absolute measurement
6. Press the ABS button in relative mode (with “ABS” displaying), and the caliper is ready for relative measurement and simultaneously displays”ABS”, showing relative mode
7. .Press ABS at any position for relative/absolute measurement interchange.
8. ZERO button
9. In relative mode, press the ZERO button to set the current point to zero and the caliper will display zero.
10. In absolute mode, press the ZERO button to set the current point to the preset value and the caliper will display this value.
11. MM/IN button
12. Press the mm/in button at any position for metric/inch conversion.
13. SET button and Internal Measuring (Easy one-touch set)
14. It’s for presetting a starting point (the value has been preset to zero in the factory)
15. With each one press this button at any position.
    The current point is set to the preset value and displayed on the LCD. The details are as follows:

For optional measuring

|

9

|

1.omm/o.3935″

| for internal measuring of 300mm calipers
2| 20.32mm/0.8″
3| 25.4mm/0.1″|

10

| 2.0mm/0.?B?0″| for internal measuring of 500mm &1000mm calipers
4| 50. Bmm/0.2″
5| 76.2mm/0.3″| 11| 2.5mm/0.9840″| for optional measuring
6| 101.6mm/0.4″| 12| 5.0mm/1.9685″| for optional measuring
7| 127mm/0.5″| 13| 0| standard. After internal and

optional measuring, please set for normal measuring.

8| 152.4mm/0.6″
3. The process is cumulative. The preset value is held even after powering off. 6. HOLD button

1. Press the “H” button at any position, the caliper will hold the value as before and display”H” on the LCD. The data will not change even if you move the slider.
2. Press the “H” button once again to release the hold state (no character “H” displays), then the caliper displays the measured value.
3.  Restart the caliper after powering off by pressing the ON/OFF button, it will keep the last state (mm/in, ABS/INC, SET).

WARNING
THE SAFETY INFORMATION GIVEN INSIDE MUST BE READ AND UNDERSTOOD BY ANY PERSON USING, INSTALLING, REPAIRING OR MAINTAINING THESE PRODUCTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>