Makita 1100 Power Planer Instruction Manual
- June 17, 2024
- Makita
Table of Contents
Makita 1100 Power Planer
- Bolt
- Drum
- Planer blade
- Drum cover
- Adjust plate
- Blade edge
- Screws
- Heel
- Back side of gauge base
- Inside edge of gauge plate
- Gauge plate
- Gauge base
- Pan head screw
- Planer blade locating lugs
- Heel of adjust plate
- Set plate
- Inside flank of gauge plate
- Mini planer blade
- Hex. flange head bolt
- Groove
- Knob
- Switch trigger
- Lock button/Lock-off button
- Start
- End
- Blade edge
- Cutting line
- Screw
- Edge fence
- “V” groove
- Front base
- Align the “V” groove with the edge of the workpiece.
- Sharpening holder
- Wing nut
- Blade (A)
- Blade (B)
- Side (C)
- Side (D)
- European type (round) chip
- Makita vacuum cleaner
- Standard (non-round) chip cover
- Limit mark
- Screwdriver
- Chip cover
- Brush holder cap
SPECIFICATIONS
- Model 1100
- Planing width ……………………………………………….. 82 mm
- Planing depth ………………………………………………… 3 mm
- Shiplapping depth ………………………………………… 20 mm
- No load speed (RPM) ……………………………………. 16,000
- Overall length …………………………………………….. 415 mm
- Net weight ……………………………………………………. 4.9 kg
Due to the continuing program of research and development, the
specifications herein are subject to change without notice.
Note : Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of the same voltage as
indicated on the nameplate, and can only be operated on single-phase AC
supply. They are double-insulated in accordance with European Standard and
can, therefore, also be used from sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed Safety instructions.
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to planer safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.
- Wait for the cutter to stop before setting the tool down. An exposed cutter may engage the sur-face leading to possible loss of control and serious injury.
- Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
- Rags, cloth, cord, string and the like should never be left around the work area.
- Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation.
- Use only sharp blades. Handle the blades very carefully.
- Be sure the blade installation bolts are securely tightened before operation.
- Hold the tool firmly with both hands.
- Keep hands away from rotating parts.
- Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced blade.
- Make sure the blade is not contacting the work-piece before the switch is turned on.
- Wait until the blade attains full speed before cut-ting.
- Always switch off and wait for the blades to come to a complete stop before any adjusting.
- Never stick your finger into the chip chute. Chute may jam when cutting damp wood. Clean out chips with a stick.
- Do not leave the tool running. Operate the tool only when hand-held.
- Always change both blades or covers on the drum, otherwise the resulting imbalance will cause vibration and shorten tool life.
- Use only Makita blades specified in this manual.
- Always use the correct dust mask/respirator for the material and application you are working with.
SAVE THESE INSTRUCTIONS.
WARNING
MISUSE or failure to follow the safety rules stated in this instruction manual
may cause serious personal injury.
OPERATING INSTRUCTIONS
Removing or installing planer blades Important
- Always be sure that tool is switched off and unplugged before removing or installing the blade.
- Use the following planer blades.
Part Nos. 793004-6 793007-0 793322-2
A- 07406 P-04226 P-04282
P-04298 820044-1 820045-1
820043-1
Blades with * mark are available in European countries only. Consult your dealer or the Makita Service Center when purchasing blades.
For tool with standard planer blades
(Fig. 1, 3 & 4)
- To remove the blades on the drum, unscrew the three installation bolts with the socket wrench. The drum cover comes off together with the blades.
- To install the blades, first clean out all chips or foreign matter adhering to the drum or blades. Use blades of the same dimensions and weight, or drum oscillation/vibra-tion will result, causing poor planing action and, eventu-ally, tool breakdown.
- Place the blade on the gauge base so that the blade edge is perfectly flush with the inside edge of the gauge plate. Place the adjust plate on the blade, then simply press in the heel of the adjust plate flush with the back side of the gauge base and tighten two screws on the adjust plate. Now slip the heel of the adjust plate into the drum groove, then fit the drum cover on it. Tighten the three installation bolts evenly and alternately with the socket wrench.
For tool with mini planer blades (Fig. 1, 5 & 6)
- Remove the existing blade, if the tool has been in use, carefully clean the drum surfaces and the drum cover. To remove the blades on the drum, unscrew the three installation bolts with the socket wrench. The drum cover comes off together with the blades.
- To install the blades, loosely attach the adjust plate to the set plate with the pan head screws and set the mini planer blade on the gauge base so that the cut-ting edge of the blade is perfectly flush with the inside flank of the gauge plate.
- Set the adjust plate/set plate on the gauge base so that the planer blade locating lugs on the set plate rest in the mini planer blade groove, then press in the heel of the adjust plate flush with the back side of the gauge base and tighten the pan head screws.
- It is important that the blade sits flush with the inside flank of the gauge plate, the planer blade locating lugs sit in the blade groove and the heel of the adjust plate is flush with the back side of the gauge base. Check this alignment carefully to ensure uniform cut-ting.
- Slip the heel of the adjust plate into the groove of the drum.
- Set the drum cover over the adjust plate/set plate and screw in the three hex flange head bolts so that a gap exists between the drum and the set plate to slide the mini planer blade into position. The blade will be positioned by the planer blade locating lugs on the set plate.
- The blade’s lengthwise adjustment will need to be manually positioned so that the blade ends are clear and equidistant from the housing on one side and the metal bracket on the other.
- Tighten the three hex flange head bolts (with the socket wrench provided) and hand rotate the drum to check clearances between the blade ends and the tool body.
- Check the three hex flange head bolts for final tight-ness.
- Repeat procedures 1 – 9 for other blade.
For shiplapping (Fig. 7)
The blade edge should be made to protrude outside slightly (0.3 mm – 0.6 mm).
Otherwise, nicks and gener-ally poor shiplapping results.
CAUTION
Tighten the blade installation bolts carefully when attaching the blades to
the tool. A loose installation bolt can be dangerous. Always check to see they
are tightened securely.
For the correct planer blade setting
Your planning surface will end up rough and uneven, unless the blade is set
properly and securely. The blade must be mounted so that the cutting edge is
absolutely level, that is, parallel to the surface of the rear base. Below are
some examples of proper and improper settings.
- (A) Front base (Movable shoe)
- (B) Rear base (Stationary shoe)
Adjusting depth of cut (Fig. 8)
Depth of cut may be adjusted by simply turning the knob on the front of the
tool.
Switch action
CAUTION
Before plugging in the tool, always check to see that the switch trigger
actuates properly and returns to the “OFF” position when released.
For tool without lock button and lock-off button (Fig. 9)
To start the tool, simply pull the trigger. Release the trigger to stop.
For tool with lock button (Fig. 10)
To start the tool, simply pull the trigger. Release the trigger to stop. For
continuous operation, pull the trigger and then push in the lock button. To
stop the tool from the locked position, pull the trigger fully, then release
it.
For tool with lock-off button (Fig. 10)
To prevent the trigger from being accidentally pulled, a lock-off button is
provided. To start the tool, press the lock-off button and pull the trigger.
Release the trigger to stop.
Planing operation (Fig. 11)
First, rest the tool front base flat upon the workpiece sur-face without the
blades making any contact. Switch on and wait until the blades attain full
speed. Then move the tool gently forward. Apply pressure on the front of tool
at the start of planing, and at the back at the end of planing. Planing will
be easier if you incline the workpiece in sta-tionary fashion, so that you can
plane somewhat down-hill.
The speed and depth of cut determine the kind of finish. The power planer
keeps cutting at a speed that will not result in jamming by chips. For rough
cutting, the depth of cut can be increased, while for a good finish you should
reduce the depth of cut and advance the tool more slowly.
Ship lapping (Fig. 12, 13, 14 & 15)
To make a stepped cut as shown in Fig. 12, use the edge fence.
Draw a cutting line on the workpiece. Insert the edge fence into the hole in
the front of the tool. Align the blade edge with the cutting line.
Adjust the edge fence until it comes in contact with the side of the
workpiece, then secure it by tightening the screw.
You may wish to add to the length of the fence by attaching an extra piece of
wood. Convenient holes are pro-vided in the fence for this purpose.
NOTE
When planning, move the tool with the edge fence flush with the side of the
workpiece. Otherwise uneven planing may result. Max. shiplapping depth is 20
mm.
Chamfering (Fig. 16, 17 & 18)
To make a cut as shown in Fig. 16, align the “V” groove in the front base with
the edge of the workpiece and plane it as shown in the Fig. 18.
Sharpening planer blades (Fig. 19, 20 & 21)
For standard blades only
Always keep your blades sharp for the best performance possible. Use the
sharpening holder to remove nicks and produce a fine edge.
First, loosen the two wing nuts on the holder and insert the blades (A) and
(B), so that they contact the sides (C) and (D). Then tighten the wing nuts.
Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold
the holder so that the blades both contact the dressing stone for simultaneous
sharp-ening at the same angle.
Connecting a vacuum cleaner
For tool with European type (round) chip cover (Fig. 22 & 23)
When you wish to perform clean planning operation, connect a Makita vacuum
cleaner to your tool as shown in Fig. 23.
For tool with standard (non-round) chip cover (Fig. 24)
Any Makita vacuum cleaner cannot be connected to the tool with the standard
(non-round) chip cover.
MAINTENANCE
CAUTION
Always be sure that the tool is switched off and unplugged before carrying out
any work on the machine.
Replacement of carbon brushes (Fig. 25, 26 & 27)
Replace carbon brushes when they are worn down to the limit mark. First,
remove the chip cover and then replace the carbon brushes. Both identical
carbon brushes should be replaced at the same time.
To maintain product safety and reliability, repairs, maintenance or adjustment
should be carried out by Makita Authorized Service Center.
ACCESSORIES
CAUTION
These accessories or attachments are recommended for use with your Makita tool
specified in this manual. The use of any other accessories or attachments
might present a risk of injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regarding these accessories, ask
your local Makita service center.
- Planer blade (2 per pkg.)
- Tungsten carbide tipped mini planer blade (2 per pkg.)
- Sharpening holder assembly
- Dressing stone
- Blade gauge assembly
- Socket wrench
- Edge fence (guide rule)
- Dust bag assembly
- Planer stand
Makita Corporation
Anjo, Aichi, Japan
883001F912
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>