Teslaunch 3 6.86 Inch Screen Instrument Cluster Mini Display Installation Guide

Teslaunch 3 6.86 Inch Screen Instrument Cluster Mini Display

Product Usage Instructions

Specifications

• Model: 3/Y H6 Instrument Cluster Display
• Tools required for installation: Plastic pry bar, Small Phillips screwdriver

Installation Precautions

Before starting the installation process, please verify the version and power off the screen.

Installation Steps – H6 Screen

1. Use a pry bar to pry open the left and right small side panels.
2. Use a pry bar to pry open the middle trim panel.
3. Use a pry bar to pry open the side trim panel.
4. Pry open the trim panel after opening one round buckle.
5. Use a pry bar to pry open and remove the original cover plate from the indicated position in the image. Then, install the instrument screen in its place.
6. Connect the power cable and adapter cable of the screen, and route the wires along the wood trim panel to the footwell area.
7. Remove the cover from the passenger footwell.
   • For Intel Version: Find the second gray plug above the passenger footwell and connect the plug adapter to it.
   • For AMD Version: Connect the plug to the white plug located under the right front seat A-pillar.

Installation Steps – Front Forward Camera

1. Remove the four screws.
2. To remove the cover plate of the air conditioning vent, simply unclip the two side fasteners and pull it out.
3. After removing the cover plate, take out the retaining clip.
4. After unplugging this connector, remove the Frunk cover.
5. Start routing the wires by using a fish tape to thread the wires from the grille below the license plate into the engine compartment.
6. Wrap the camera cable around the fish tape and thread it into the engine compartment.
7. Install the camera bracket in the correct position and tighten the screws once it is aligned properly.
8. Thread the fish tape from the rubber plug near the air conditioning vent into the driver’s seat.
9. Once the fish tape is visible from the passenger side, pull it inside.
10. Connect the camera cable and route it along the wood trim panel. Once the wiring is in place, restore the vehicle to its original condition.

FAQs

• Q: What tools are required for installation?
  • A: You will need a plastic pry bar and a small Phillips screwdriver.
• Q: What precautions should I take before installation?
  • A: Please verify the version and power off the screen before starting the installation process.
• Q: How do I install the H6 Screen?
  • A: Follow these steps:
  • Pry open the left and right small side panels.
  • Pry open the middle trim panel.
  • Pry open the side trim panel.
  • Pry open the trim panel after opening one round buckle.
  • Remove the original cover plate and install the instrument screen in its place.
  • Connect the power cable and adapter cable of the screen, routing the wires along the wood trim panel to the footwell area.
  • Remove the cover from the passenger footwell and connect the appropriate plug adapter.
• Q: How do I install the Front Forward Camera?
  • A: Follow these steps:
  • Remove the four screws.
  • Unclip the two side fasteners and pull out the cover plate of the air conditioning vent.
  • Take out the retaining clip after removing the cover plate.
  • Unplug the connector and remove the Frunk cover.
  • Route the wires from the grille below the license plate into the engine compartment using a fish tape.
  • Thread the camera cable into the engine compartment using the fish tape.
  • Install the camera bracket and tighten the screws.
  • Thread the fish tape from the rubber plug near the air conditioning vent into the driver’s seat and pull it inside from the passenger side.
  • Connect the camera cable, route it along the wood trim panel, and restore the vehicle to its original condition.

Tools Required

Tools required for installation

• Plastic pry bar;
• Small Phillips screwdriver

Installation precautions

• Verify the version and power off the screen before installation.

Note: To expedite the installation process, please carefully read this instruction manual.

Packing List

Inspection Before And After Installation

NOTE

1. Before installation, please check if the product list is complete and free of damage
2. The installation instructions may differ slightly from actual operation. If there are any discrepancies, please refer to the actual situation or contact us.
3. Warning: Do not disassemble any components on your own. Any improper operations are not covered under warranty.
4. Please confirm the version information and turn off the vehicle power before installing the product.
5. Please watch the installation video and instruction manual before installing the product.
6. Before turning on the product after installation, please confirm that the installation and wiring are correct.
7. Check if the installed product functions properly. If there are any issues, please check if the plug is securely inserted.
8. Check if the original vehicle functions are working properly. If there are any issues, please check if the plug is securely inserted.
9. Please do not install the product if you receive a damaged item. Please take photos immediatel and provide them to out after-sales team for confirmation, Photos should be provided that include all parts of the product and can display the damage. (If the product is notified of the damage after installation. claims and reissues will not be accepted. and vou will need to purchase the parts again at your own expense.)

Installation Steps

Installation Steps – H6 Screen

1. Use a pry bar to pry open the left and right small side panels.
2. Use a pry bar to pry open the middle trim panel
3. Use a pry bar to pry open this side trim panel
4. Pry open this trim panel after opening one round buckle.
5. Use a pry bar to pry open and remove the original cover plate from the indicated position in the image. Then, install the instrument screen in its place.
6. Connect the power cable and adapter cable of the screen, and route the wires along the wood trim panel to the footwell area.
7. Remove the cover from the passenger footwell.
8. Intel Version: Find the second gray plug above the passenger footwell and connect the plug adapter to it.

AMD Version:

1. Connect the plug to the white plug located under the right front seat A-pillar
2. Connect the plug to the blue plug located under the right front seat A-pillar.

Front Forward Camera

Installation steps for front camera:

1. Remove these four screws.
2. To remove the cover plate of the air conditioning vent, simply unclip the two side fasteners and pull it out.
3. After removing the cover plate, take out the retaining clip.
4. After unplugging this connector, remove the Frunk cover
5. Start routing the wires by using a fish tape to thread the wires from the grille below the license plate into the engine compartment.
6. Wrap the camera cable around the fish tape and thread it into the engine compartment.
7. Install the camera bracket in the correct position and tighten the screws once it is aligned properly.
8. Thread the fish tape from the rubber plug near the air conditioning vent into the driver’s seat.
9. Once the fish tape is visible from the passenger side, pull it inside
10. Connect the camera cable and route it along the wood trim panel. Once the wiring is in place, restore the vehicle to its original condition.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>