PUTORSEN PPT-CM322 Fold Up TV Ceiling Mount Instruction Manual

PUTORSEN PPT-CM322 Fold Up TV Ceiling Mount

Product Information

Specifications:

• Model: PPT-CM322
• VESA Mounting Patterns: 75×75, 100×100, 100×200, 200×100, 200×200

Package Contents:

• Ceiling Mount
• Hex Wrench
• VESA Mounting Hardware
• Wrench
• Cable Ties
• Wall Mounting Hardware
  If any parts are missing, please contact us through Amazon and we will ship you replacements free of charge. For any questions or problems, please contact us through Amazon and we will reply within 24 hours.

Product Usage Instructions

• Step 1: Take Off VESA Plate
  This ceiling TV mount can be installed on wood stud ceiling, concrete ceiling, and brick ceiling. Please follow the appropriate mounting steps based on your actual ceiling type:

  • Wood Stud Ceiling Installation:
  1. Unfold the Ceiling Plate.
  2. Locate the keyhole on the ceiling plate.
  3. Take off the VESA plate from the mount.
  • Concrete Ceiling & Brick Ceiling Installation:
  1. Unfold the Ceiling Plate.
  2. Locate the keyhole on the ceiling plate.
  3. Take off the VESA plate from the mount.

• Step 2: Install the VESA Plate to Your TV
  Attach the VESA plate to the back of your TV using the provided VESA mounting hardware.

• Step 3: Install TV to the Ceiling Mount
  Place your TV onto the ceiling mount by aligning the VESA plate with the mount. Ensure that it is securely attached.

• Step 4: Adjustments
  Make necessary adjustments to achieve the desired viewing angle. Refer to the foldable design instructions for space-saving options.

• Step 5: Tighten Screw to Secure TV to the Ceiling Mount
  Using the wrench, tighten the screw to firmly secure your TV to the ceiling mount.

Cable Management
Organize and manage your cables using the provided cable ties for a clean and tidy installation.

FAQ

• What VESA mounting patterns are supported?
  The mount supports VESA mounting patterns of 75×75, 100×100, 100×200, 200×100, and 200×200.

• Can this mount be installed on different types of ceilings?
  Yes, this mount can be installed on wood stud ceilings, concrete ceilings, and brick ceilings.

CAUTION

• Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance

• CAUTION: Use with products heavier than the rated weights indicated may result in instability causing p0&&ible injury.

  • Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
  • Safety gear and proper tools must be used. This product should only be installed by professionals.
  • This product Is designed to be Installed on concrete celling or wood Joist celling.
  • Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  • Use the mounting screws provided and DO NOT OVER TIGHTEN mounting saews.
  • This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
    IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

• MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

PACKAGE CONTENTS

VESA MOUNTING HARDWARE

WALL MOUNTING HARDWARE

Please contact us through Amazon if you miss any parts and we will ship you replacement free of charge.
Please contact us through Amazon if you have any questions or problems and we will reply you within 24 hours.

IMSTALLATION INSTRUCTION

• Step 1 Take Off VESA Plate
  Use Alen Key(F) to remove the bolt and take off the VESA plate from the folding arm. Please keep this bolt because it will be used again in the following time.

• Step 2 Unfold the Ceiling Plate

  • Pull out of the folding arm to release the hook which from the ceiling plate. Then put down the folding arm as a preparesion for the next step.
  • This ceiling tv mount can be installed on wood stud ceiling, concrete ceiling & brick ceiling. Please find following two mounting steps according to your actual ceiling about (1) wood stud ceiling; (2) concrete ceiling & brick ceiling

• Step 3a Wood Stud Ceiling Installation

  • Firstly, you need to rotate the arm as shown below. Then you need to use a stud finder to find the wood stud from the ceiling and use a pencil to mark it(Make sure two holes are in the central of the wood stud. And please also attention you should mark the central of smaller side of the keyhole as shown below)

  • Secondly, you can drill two holes according to the two marked locations.
    Thirdly, you should install 1 self-tapping screw(W-A) like show below and leave a gap about 0.16”(4mm) between the bottom of the screw head and the ceiling.

  • Then Hang the ceiling mount on this screw and slide in it as shown below. After this, you can install another screw(W-A) with a washer(W-C).

  • Finally, tighten both two screws. Rotate the arm back to the original position as shown.

• Step 3b Concrete Ceiling & Brick Ceiling Installation

  • Firstly, you should use the ceiling plate and mark the locations(make sure mark the central of the holes. And please also attention you should mark the central of smaller side of the keyhole as shown below)
  • Secondly, clear these holes and then insert 4 anchors(W-B).
  • Thirdly, install 2 screws(W-A) first on the keyhole side and do not tighten fully, leaving a gap about 0.16”(4mm) between the bottom of the screw head and the ceiling.
  • Then Hang the ceiling mount on these screws and slide as shown below. After this, you can install another two screws(W-A) with washers(W-C).
  • Finally, tighten all screws.

• Step 4 Install the VESA Plate to your TV

  • Put your TV screen side down on a flat and soft surface.

  • Please choose the suitable TV mounting screws(M-A through M-D), washers(M-E) according to your VESA hole depth from your back TV.
    NOTE: Please check TV instruction manual or contact TV seller to get the correct information if you are not sure about the VESA hole depth.

  • Then if necessary, you can use spacers(M-F and M-G) between the mount and TV as shown below to adjust the length of the mounting screw, which be in order to get the requested screw depth.
    Install VESA plate on to the TV using selected screws and washers(and also spacers if necessary).
    NOTE: Please do NOT overtighten for TV protection.

• Step 5 Install TV to the Ceiling Mount
  Hang your TV onto the front of the ceiling mounting arm as shown below. Use the screw which take off from step 1 and reinstall. If you need to adjust the TV height, please loosen the screw as shown, slide the mount to the requested height and then tighten this screw.
  NOTE: This TV installation step may need two people to protect your TV .
  

• Step 6 Tighten Screw to Secure TV to the Ceiling Mount
  Let TV unable to be moved from the ceiling mounting arm.

• Step 7 Adjustments
  Remove the decorative cover, use the Allen key to loosen or tighten the screw as shown for smooth tilting adjustment of the bracket, and then put the cover back.
  

Foldable Design

Cable Management

We include 4pcs zip ties as an extra value and you can use them for any cable management if needed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>