Yeacomm ODU NR610 Series 5g 4g Modem Odu Dual Sim Router User Manual

Yeacomm ODU NR610 Series 5g 4g Modem Odu Dual Sim Router

ODU Interfaces And Indicators Light Description

ODU Interfaces Description

ODU Configuration Introduction

ODU LED Indicators Description

1. Blue light on, Power on
2. 0ff, Power off

| LAN|

1. Blue light blinking, Ethernet connected
2. 0ff, Ethernet not connect

| WIFI|

1. Blue light on, WIFI on
2. 0ff, WIFI off

4G/5G

| Cellular 2Yellow light on, connect to 3G/4G network

Network

|

1. Blue light on, connect to SG network
2. Yellow light on, connect to 3G/4G network
3. 0ff, not connect to cellular network
4. Blinking, dialing, blinking frequency 500ms/time

| Signal Strength|

1. Blue light on, signal is good, the signal value RSRP>- 95dBm or RSCP>-80
2. Yellow light on, signal is weak, the signal value RSRPs- 95dBm or RSCPs-80
3. 0ff, no signal ,s available or no SIM card is inserted

Set up SIM Card & Internet Access (POE Power Supply)

Step 1: Unscrew the two screws on the cover of the device and remove the cover.

Step 2: Insert SIM card direction shown on the SIM card interface, the left side of the card slot is the secondary card, and the right side is the main card.

Step 3: Lock the cover plate of the equipment with screws.

Step 4: Insert the network cable into the waterproof connector by following the steps from left to right in the pictures, tighten the waterproof connector, insert the cable into the LAN port of the device, and tighten the waterproof connector with the device.
Notice: It is recommended to use a wrench to tighten. not tight may affect the waterproof performance.

Step 5: Connect the network cable to the POE port of the POE adapter, connect the POE adapter to the power supply and the 5G ODU device automatically turn on. And connect a network cable to the LAN port of the POE adapter and connect the IDU to provide a wired or wireless network for other internet devices.

Set up SIM Card & Internet Access (DC Power Supply)

SIM Card Installation refer to Step 1 to Step 3 in Set up SIM Card Internet Access (POE Power Supply)

Step 4: Insert the DC power cable into the waterproof connector by following the steps from left to right in the pictures, tighten the waterproof connector, insert it into the DC port, tighten the waterproof connector, and power on device.

Notice: If the DC power cable is too thin, wrap several rounds of waterproof tape around the coil to improve the waterproof performance.

Step 5 Network cable installation refer to Step 4 in Set up SIM Card Internet Access (POE Power Supply)
Step 6: Connect network cable to IDU to provide wired or wireless network for other network devices .

Device Installation (Wall-mounted)

• Wall Bracket Base Pole Hoop

• Base

• Pole Hoop

Step 1: Lock the base to the device.

Step 2: Connect with the wall bracket and lock the screws to fix.

Step 3: Align the four screw holes of the wall bracket with the wall that has been drilled through the mounting holes and lock the expansion screws for fixing.

Device Installation (Pole-mounted)

For the installation of the base and wall bracket refer to the Step 1 to Step 2 in Device Installation (Wall-mounted).
Step 3: The hole hoop is inserted into the hole of the wall bracket. put on the pole, and fixed by locking the screw

Device Configuration

Step 1: Power the device, the signal strength indicator is on, the dial is successful if the 5G/4G indicator is on .

Step 2: The terminal devices could access the ODU by Lan port or WIFI.
WIFI SSID: ODU_2.4G_XXXX (Pis notice that the ODU WIFI is only for easy configuration, not for speediest).

Step 3: Open the browser, and the page is automatically displayed. (If no, manually enter 192. 168.1.1 )
Default   Account. admin
Default Password: admin

Step 4: Set the username and password for the WLAN.

Step 5: Set the password for logging in the host. After the application setting is complete, the login page will be displayed. Enter the password of the new account and click login.

Step 6: Set the APN.
If the device doesn’t recognize the APN automatically.
Then pls disable the setting ”Auto configuration by SIM’ and add the APN manually.

Precautions:
If you use the Yeacomm NR610 5G Router with a T-Mobile sim card, pls do the setting manually as follows to make it connect to internet.

1. Choose Networking Mode “NS.A:’ setting.
   (Network Setting — Mobile Network –Mobile Network Settings)
   If still no network connection, change the Networking Mode to “SA”
   

2. Choose IP Type “IPV4” settings.
   (Network Setting — Mobile Network –Advanced Settings)
   If still no network connection, change the IP Type to “IPV6”.
   

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Radiation Exposure Statement
  This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body

CUSTOMER SUPPORT

Tech Support
Website: www.yifanwireless.com
Email: support@yifanrouter.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>